OEM VERIFIED BENCH

OFFICIAL FAULT CODEE07

Rosieres // OFFICIAL DIAGNOSTIC BENCH

Rosieres E07

Washing MachineDrive Motor, Inverter & Tachometer Sensor

Washing Machine

Other Brands Sharing Code E07:BoschE07 SiemensE07 ElectroluxE07 AEGE07 CandyE07 NeffE07 HooverE07 ZanussiE07 Arthur MartinE07 GaggenauE07

Symptom / Description

FAULT

Motor Fault / Jammed Motor

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

The motor is jammed, or the motor's tacho sensor is faulty, preventing the motor from turning correctly.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Check if the drum can be turned by hand. Inspect the motor, its carbon brushes (if applicable), and the wiring to the tacho sensor. Replace brushes or motor if necessary.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Rosieres Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Rosieres E07

FAQ TREE

What does error code E07 mean on a Rosieres appliance?

Rosieres error code E07 indicates: Motor Fault / Jammed Motor.

What is the root cause of Rosieres error code E07?

The primary root cause for Rosieres code E07 is: The motor is jammed, or the motor's tacho sensor is faulty, preventing the motor from turning correctly..

How do I fix or resolve Rosieres error code E07?

To resolve error code E07: Check if the drum can be turned by hand. Inspect the motor, its carbon brushes (if applicable), and the wiring to the tacho sensor. Replace brushes or motor if necessary.

Is it safe to clear Rosieres error code E07 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Rosieres code E07 persists, the physical component causing The motor is jammed, or the motor's tacho sensor is faulty, preventing the motor from turning correctly. must be inspected or replaced.

How do I test electrical resistance for Rosieres code E07 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test 3-Phase Motor Windings / Tacho Generator / Carbon Brushes across Across phase pins U-V, V-W, U-W on motor harness; across tacho pins. Expected nominal reading is 3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator). Tolerance: BLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho..

What safety protocol must be followed before servicing Rosieres code E07?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE07

Rosieres // OFFICIAL DIAGNOSTIC BENCH

Rosieres E07

Washing MachineDrive Motor, Inverter & Tachometer Sensor

Washing Machine

Other Brands Sharing Code E07:BoschE07 SiemensE07 ElectroluxE07 AEGE07 CandyE07 NeffE07 HooverE07 ZanussiE07 Arthur MartinE07 GaggenauE07

Symptom / Description

FAULT

Motor Fault / Jammed Motor

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

The motor is jammed, or the motor's tacho sensor is faulty, preventing the motor from turning correctly.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Check if the drum can be turned by hand. Inspect the motor, its carbon brushes (if applicable), and the wiring to the tacho sensor. Replace brushes or motor if necessary.

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Rosieres Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Rosieres E07

FAQ TREE

What does error code E07 mean on a Rosieres appliance?

Rosieres error code E07 indicates: Motor Fault / Jammed Motor.

What is the root cause of Rosieres error code E07?

The primary root cause for Rosieres code E07 is: The motor is jammed, or the motor's tacho sensor is faulty, preventing the motor from turning correctly..

How do I fix or resolve Rosieres error code E07?

To resolve error code E07: Check if the drum can be turned by hand. Inspect the motor, its carbon brushes (if applicable), and the wiring to the tacho sensor. Replace brushes or motor if necessary.

Is it safe to clear Rosieres error code E07 by resetting power?

How do I test electrical resistance for Rosieres code E07 using a multimeter?

What safety protocol must be followed before servicing Rosieres code E07?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Rosieres E07

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Rosieres E07

Community Verification

Related Rosieres Washing Machine Error Codes

Rosieres E07

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Rosieres E07

Community Verification

Related Rosieres Washing Machine Error Codes