OEM VERIFIED BENCH

OFFICIAL FAULT CODEEr10

Sauter // OFFICIAL DIAGNOSTIC BENCH

Sauter Er10

OvenDrainage System & Drain Pump

Oven

Other Brands Sharing Code Er10:BrandtER10 De DietrichER10 FAGORER10 AirluxER10 AtlanticER-10

Symptom / Description

FAULT

Sauter Saveurs / Confort / Amphora / SFP Pyrolytic Oven: Steam boiler water evacuation fault Er10; drain pump fails to pump residual water out of the steam boiler.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Sauter steam combi ovens featuring Saveurs gentle convection airflow, Conseil Température cooking guide, and Amphora enamel heat reflection: Calcium flakes wedging the mini drain pump impeller, blocked silicone drain tube, or open pump coil (~150–220 Ω).

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Inspect mini drainage pump below steam generator. Clear scale obstructions from pump chamber. Measure pump coil resistance (~150–220 Ω). Turn selector to Off, drop power at the branch breaker for 60 seconds, restore supply and touch the clock icon to recalibrate.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Sauter Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpOven / Microwave

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Sauter ER10

FAQ TREE

What does error code ER10 mean on a Sauter appliance?

Sauter error code ER10 indicates: Sauter Saveurs / Confort / Amphora / SFP Pyrolytic Oven: Steam boiler water evacuation fault Er10; drain pump fails to pump residual water out of the steam boiler..

What is the root cause of Sauter error code ER10?

The primary root cause for Sauter code ER10 is: On Sauter steam combi ovens featuring Saveurs gentle convection airflow, Conseil Température cooking guide, and Amphora enamel heat reflection: Calcium flakes wedging the mini drain pump impeller, blocked silicone drain tube, or open pump coil (~150–220 Ω)..

How do I fix or resolve Sauter error code ER10?

To resolve error code ER10: Inspect mini drainage pump below steam generator. Clear scale obstructions from pump chamber. Measure pump coil resistance (~150–220 Ω). Turn selector to Off, drop power at the branch breaker for 60 seconds, restore supply and touch the clock icon to recalibrate.

Is it safe to clear Sauter error code ER10 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Sauter code ER10 persists, the physical component causing On Sauter steam combi ovens featuring Saveurs gentle convection airflow, Conseil Température cooking guide, and Amphora enamel heat reflection: Calcium flakes wedging the mini drain pump impeller, blocked silicone drain tube, or open pump coil (~150–220 Ω). must be inspected or replaced.

How do I test electrical resistance for Sauter code ER10 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Sauter code ER10?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEEr10

Sauter // OFFICIAL DIAGNOSTIC BENCH

Sauter Er10

OvenDrainage System & Drain Pump

Oven

Other Brands Sharing Code Er10:BrandtER10 De DietrichER10 FAGORER10 AirluxER10 AtlanticER-10

Symptom / Description

FAULT

Sauter Saveurs / Confort / Amphora / SFP Pyrolytic Oven: Steam boiler water evacuation fault Er10; drain pump fails to pump residual water out of the steam boiler.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Sauter Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpOven / Microwave

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Sauter ER10

FAQ TREE

What does error code ER10 mean on a Sauter appliance?

Sauter error code ER10 indicates: Sauter Saveurs / Confort / Amphora / SFP Pyrolytic Oven: Steam boiler water evacuation fault Er10; drain pump fails to pump residual water out of the steam boiler..

What is the root cause of Sauter error code ER10?

How do I fix or resolve Sauter error code ER10?

Is it safe to clear Sauter error code ER10 by resetting power?

How do I test electrical resistance for Sauter code ER10 using a multimeter?

What safety protocol must be followed before servicing Sauter code ER10?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Sauter Er10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Sauter ER10

Community Verification

Related Sauter Oven / Microwave Error Codes

Sauter Er10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Sauter ER10

Community Verification

Related Sauter Oven / Microwave Error Codes