Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code Door Alarm registered by the microcomputer controller. Door left open optical and acoustic warning tone active >60 seconds
Compressor Motor Windings (Run/Start) & Defrost Heater
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code E0 registered by the microcomputer controller. Communication loss between door display and base power module
Compressor Motor Windings (Run/Start) & Defrost Heater
Liebherr Gourmet Built-in Convection Oven: Diagnostic fault code E4 registered by the microcomputer controller. Liebherr: Communication error between user interface and power module.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Liebherr Gourmet Built-in Convection Oven: Diagnostic fault code E8 registered by the microcomputer controller. Liebherr E8: Motor drive or inverter rotation anomaly in Oven / Microwave; drum/motor fails to spin at target RPM.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Liebherr Gourmet Built-in Convection Oven: Diagnostic fault code E9 registered by the microcomputer controller. Liebherr E9: NTC temperature sensor signal out of range (open or short circuit) in Oven / Microwave.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code E14 registered by the microcomputer controller. Mains power frequency out of 50 Hz ± 3 Hz tolerance range
Compressor Motor Windings (Run/Start) & Defrost Heater
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F3 registered by the microcomputer controller. Freezer interior air temperature measurement out of specification
Compressor Motor Windings (Run/Start) & Defrost Heater
Liebherr Premium AquaStop Integrated Dishwasher: Diagnostic fault code F11 registered by the microcomputer controller. Liebherr F11: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code SN registered by the microcomputer controller. Internal serial network bus communication timeout between boards
Compressor Motor Windings (Run/Start) & Defrost Heater
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F2 registered by the microcomputer controller. Fresh food evaporator surface temperature probe circuit fault
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: evaporator plate NTC sensor behind liner open or grounded Metrological tolerance verification: nominal 4.7 kΩ at 25°C, 16.5 kΩ at -2°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: check resistance across evaporator thermistor pins; replace sensor kit if open (>250 kΩ). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F03 registered by the microcomputer controller. NoFrost freezer zone interior air NTC probe open circuit
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: freezer air probe element open-circuited Metrological tolerance verification: nominal 4.7 kΩ at 25°C, 35.7 kΩ at -18°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: check probe resistance at terminal strip X4. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F3 registered by the microcomputer controller. Freezer interior air temperature measurement out of specification
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: freezer cabinet air NTC sensor defective or disconnected Metrological tolerance verification: nominal 4.7 kΩ at 25°C, 35.7 kΩ at -18°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure probe terminals at connector X4 (expected 35.7 kΩ at -18°C). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F04 registered by the microcomputer controller. NoFrost freezer evaporator defrost termination NTC short
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: defrost probe wire shorted to aluminum fins Metrological tolerance verification: resistance < 100 Ω..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: replace defrost termination NTC probe. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: evaporator coil defrost NTC thermistor out of tolerance Metrological tolerance verification: nominal 4.7 kΩ at 25°C, 30.4 kΩ at -15°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: test sensor across defrost pins; ensure no short circuit (<100 Ω) to metal evaporator tubing. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F05 registered by the microcomputer controller. BioFresh dry compartment air thermistor open circuit
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: air probe harness disconnected or sensor open Metrological tolerance verification: nominal 4.7 kΩ at 25°C, 13.3 kΩ at 0°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure resistance on BioFresh sensor harness. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F5 registered by the microcomputer controller. Main power electronic control board microprocessor error
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: microcontroller RAM/ROM parity check failed or EEPROM corrupted Metrological tolerance verification: 5.0V DC regulated logic supply rail stable within ±0.1V..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: test 5V DC and 12V DC secondary voltages on power board test points. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F06 registered by the microcomputer controller. BioFresh rear chilling plate thermistor short circuit
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: chilling plate sensor shorted Metrological tolerance verification: resistance < 100 Ω..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: replace rear chilling plate thermistor kit. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr Premium AquaStop Integrated Dishwasher: Diagnostic fault code F6 registered by the microcomputer controller. Dishwasher water intake error.. Liebherr Premium AquaStop Integrated Dishwasher: Diagnostic fault code F6 reported by internal controller.
On Liebherr appliances engineered with Liebherr electronic wash management, flow-through heater, and AquaSafe leak protection: Water is not entering the appliance. The water tap may be closed, the inlet hose kinked, or the water inlet valve filter is blocked. Metrological tolerance verification: door lock mechanism motor coil 2.2 kΩ to 2.8 kΩ; microswitch 0.0 Ω closed.
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure door lock motor coil resistance (~2.5 kΩ) and verify microswitch continuity (0.0 Ω). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn off unit. Hold Start/Pause while turning on power switch, release after 4 seconds, then press Start/Pause 3 times to enter service reset mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F6 registered by the microcomputer controller. Wine conditioning cabinet upper temperature zone sensor failure
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: upper wine zone NTC temperature sensor open circuit Metrological tolerance verification: nominal 4.7 kΩ at 25°C, 8.3 kΩ at 12°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure sensor resistance across upper zone terminals at main board. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F07 registered by the microcomputer controller. External cabinet ambient compensation thermistor open circuit
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: ambient sensor on cabinet hinge cover open Metrological tolerance verification: nominal 4.7 kΩ at 25°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: test sensor continuity across hinge harness connector. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F7 registered by the microcomputer controller. Wine conditioning cabinet lower temperature zone sensor failure
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: lower wine zone NTC temperature sensor short or open circuit Metrological tolerance verification: nominal 4.7 kΩ at 25°C, 9.8 kΩ at 8°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure sensor resistance across lower zone terminals at control PCB. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F08 registered by the microcomputer controller. Condenser discharge tube safety thermistor open circuit
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: safety thermistor disconnected from copper discharge tube Metrological tolerance verification: nominal 4.7 kΩ at 25°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: check sensor clip on discharge pipe and test resistance. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
On Liebherr appliances engineered with Liebherr electronic wash management, flow-through heater, and AquaSafe leak protection: The valve that directs water to the upper or lower spray arms is stuck or faulty. Metrological tolerance verification: door lock mechanism motor coil 2.2 kΩ to 2.8 kΩ; microswitch 0.0 Ω closed.
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure door lock motor coil resistance (~2.5 kΩ) and verify microswitch continuity (0.0 Ω). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn off unit. Hold Start/Pause while turning on power switch, release after 4 seconds, then press Start/Pause 3 times to enter service reset mode.
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: plate evaporator NTC sensor regulating 0°C zone drifted Metrological tolerance verification: nominal 4.7 kΩ at 25°C, 14.5 kΩ at -1°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: check sensor resistance at PCB pins; replace foaming sensor kit if drifted. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F09 registered by the microcomputer controller. Multi-temperature wine cellar top conditioning zone thermistor open
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: zone 1 sensor open circuit Metrological tolerance verification: nominal 4.7 kΩ at 25°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure sensor resistance across zone 1 terminals. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F9 registered by the microcomputer controller. Automatic IceMaker mold temperature sensor or motor stall
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: mold NTC thermistor open or ejector gear tooth stalled Metrological tolerance verification: mold NTC 4.7 kΩ at 25°C; motor winding 4.2 kΩ..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure mold thermistor resistance and verify ejector drive motor winding continuity. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F10 registered by the microcomputer controller. Multi-temperature wine cellar bottom conditioning zone thermistor open
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: zone 2 sensor open circuit Metrological tolerance verification: nominal 4.7 kΩ at 25°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure sensor resistance across zone 2 terminals. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr Premium AquaStop Integrated Dishwasher: Diagnostic fault code F11 registered by the microcomputer controller. Liebherr F11: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.
On Liebherr appliances engineered with Liebherr electronic wash management, flow-through heater, and AquaSafe leak protection: Water is not being pumped out. Drain pump is blocked, drain hose is kinked or blocked, or non-return valve is stuck. Metrological tolerance verification: drain pump synchronous motor coil nominal 165 Ω to 180 Ω (230V AC).
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure drain pump coil resistance across terminals (expected ~170 Ω). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn off unit. Hold Start/Pause while turning on power switch, release after 4 seconds, then press Start/Pause 3 times to enter service reset mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F11 registered by the microcomputer controller. Monolith InfinitySwipe capacitive touch user interface bus timeout
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: touch display panel communication line severed Metrological tolerance verification: differential data line voltage 2.5V-3.5V DC..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: inspect Monolith door pivot cable bundle for pinched wires. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: air purification filter saturated (exceeded operating limit) Metrological tolerance verification: nominal NTC thermistor 10.0 kΩ at 25°C, 2.5 kΩ at 60°C.
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure sensor resistance across 2-pin harness connector (expected ~10 kΩ at 25°C). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F13 registered by the microcomputer controller. SoftSystem motorized door damping sensor or position microswitch
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: door damper hydraulic switch not reporting closure Metrological tolerance verification: microswitch 0.0 Ω closed..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: verify SoftSystem door damper alignment and test switch contacts. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F14 registered by the microcomputer controller. IceMaker tray twist motor mechanical stall or gear disengagement
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: ice tray twisted out of alignment or motor gear stripped Metrological tolerance verification: motor coil resistance ~4.2 kΩ..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: inspect ice cube mold and test tray rotation motor drive. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F15 registered by the microcomputer controller. IceMaker / chilled water dispenser dual solenoid valve coil open
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: solenoid valve coil open circuit or thermal fuse open Metrological tolerance verification: solenoid coil nominal 2.1 kΩ to 2.4 kΩ..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure resistance across valve coil terminals (expected ~2.1 kΩ). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F16 registered by the microcomputer controller. IceMaker infrared optical cube bin level detector blinded or failed
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: infrared optical beam blocked by frost or sensor defective Metrological tolerance verification: sensor phototransistor voltage 0.4V unblocked, 4.8V blocked..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: clean ice sensor lenses and check 5V DC supply rail. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F17 registered by the microcomputer controller. Chilled water dispenser Hall-effect flowmeter missing pulse trains
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: flowmeter turbine jammed with sediment or Hall sensor defective Metrological tolerance verification: turbine produces 2-4V square wave pulses during water dispense..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: check water inlet pressure (>1.5 bar) and verify flowmeter pulse output. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
On Liebherr appliances engineered with Liebherr electronic wash management, flow-through heater, and AquaSafe leak protection: The main wash motor (circulation pump) is blocked, has failed, or the control board is not sending power to it. Metrological tolerance verification: drain pump synchronous motor coil nominal 165 Ω to 180 Ω (230V AC).
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure drain pump coil resistance across terminals (expected ~170 Ω). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn off unit. Hold Start/Pause while turning on power switch, release after 4 seconds, then press Start/Pause 3 times to enter service reset mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F18 registered by the microcomputer controller. Internal chilled water tank reservoir temperature thermistor defect
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: water reservoir NTC sensor open or shorted Metrological tolerance verification: nominal 4.7 kΩ at 25°C, 11.8 kΩ at 5°C..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: test reservoir sensor resistance at terminal strip. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F19 registered by the microcomputer controller. PowerCooling FreshAir dynamic circulation fan motor RPM error
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: fan blade obstructed or BLDC hall sensor failed Metrological tolerance verification: 12V DC operating voltage, tachometer feedback active..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: verify fan impeller spins freely and test voltage supply. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.
Liebherr BioFresh / BluPerformance / Monolith / NoFrost Premium Refrigerator & Wine Cellar: Diagnostic fault code F20 registered by the microcomputer controller. NoFrost evaporator fan motor BLDC electronic drive locked rotor
On Liebherr appliances engineered with BioFresh climate chambers, BluPerformance base refrigeration module, DuoCooling dual refrigerant circuits, and VCC inverter compressor with 4.7 kΩ NTC thermistors: evaporator fan frozen in ice block or motor windings open Metrological tolerance verification: motor winding resistance ~45 Ω or BLDC electronic drive..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: defrost evaporator coil and test fan motor winding continuity. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn appliance on. Hold SuperFrost (or Alarm) for 5 seconds until 'c' or 'C' menu appears. Press Up/Down to navigate to '0' or 'rS', then press SuperFrost for 3 seconds to clear the fault log and exit service test mode.