Access our premium database of error codes, common faults, and professional repair solutions for Samet appliances.
Samet A01: Operational cycle fault detected during Oven / Microwave program execution.
The meat probe is not inserted correctly, is faulty, or is not connected.
Ensure the meat probe is fully inserted into the socket in the oven cavity. Test the probe for continuity; replace if faulty.
Washing machine motor overheating
The motor's thermal protector has been activated due to overheating, possibly from a prolonged heavy load.
Turn off the machine and allow the motor to cool down for at least 30 minutes before trying again.
Samet CF: Operational cycle fault detected during Refrigerator / Freezer program execution.
Communication has been lost between the main control board and the user interface/display board.
Check the wiring harness between the boards. A loose connection could be the cause, but often one of the boards has failed.
Samet E01: Door lock safety interlock fault in Washing Machine; door switch contact fails to close or open.
The washing machine door is not closed properly, or the door lock mechanism is faulty.
Ensure the door is firmly closed. Check wiring to the door interlock. Replace the door lock mechanism if faulty.
Samet E1: Operational cycle fault detected during Hob / Cooktop program execution.
The internal electronics are overheating, possibly due to blocked ventilation or prolonged use at high power.
Turn off the hob and let it cool down. Make sure the ventilation slots underneath are not blocked.
Samet E02: Water inlet / filling timeout in Washing Machine; appliance fails to fill to minimum operational level.
Low water pressure, kinked inlet hose, or a faulty water inlet valve.
Check if the water tap is fully open. Clean the filter in the inlet hose. Check and replace the inlet valve if necessary.
Samet E2: NTC temperature sensor signal out of range (open or short circuit) in Hob / Cooktop.
A temperature sensor on the induction coil or control board has failed.
This is an internal fault that requires a service technician to diagnose and replace the faulty sensor or electronic board.
Samet E03: Water drainage failure detected in Washing Machine; drain pump cannot evacuate water within safety time limit.
Drain pump filter is clogged, drain hose is blocked or kinked, or the drain pump is defective.
Clean the drain pump filter. Check the drain hose for obstructions. Test and replace the drain pump if it has failed.
Samet E3: Operational cycle fault detected during Hob / Cooktop program execution.
The voltage supplied to the hob is outside the acceptable range (too high or too low).
An electrician should check the mains electrical supply to the hob to ensure it is correct.
Overfilling / Too much water
Faulty pressure switch (level sensor) or a stuck-open water inlet valve.
Check the pressure switch and its connecting tube for blockages. If the machine fills even when off, replace the water inlet valve.
Communication error between modules
The control board is not communicating correctly with the power module for a specific cooking zone.
Reset the hob by disconnecting power for 10 minutes. If the error persists, it indicates a hardware failure requiring service.
Samet E05: NTC temperature sensor signal out of range (open or short circuit) in Washing Machine.
The heating element or the NTC temperature sensor is faulty or has an open circuit.
Test the heating element and the NTC sensor with a multimeter. Replace the defective part.
Samet E5: Operational cycle fault detected during Hob / Cooktop program execution.
Liquid or an object is on the touch control area, or the touch control board is faulty.
Wipe the control surface clean and dry. Remove any objects. If the error remains, the control panel may need replacement.
Samet E06: Motor drive or inverter rotation anomaly in Washing Machine; drum/motor fails to spin at target RPM.
The motor's carbon brushes are worn, or there is a fault with the motor tacho or the motor itself.
Check and replace the motor's carbon brushes. Inspect motor wiring and tacho coil. The motor may need replacement.
Samet E6: Operational cycle fault detected during Hob / Cooktop program execution.
Failure of the power board that supplies energy to the induction coils.
This is a critical internal error. The hob requires inspection and repair by a qualified technician.
Control board configuration error
The main electronic control board (PCB) is misconfigured or has failed.
This error usually requires a service technician to re-program or replace the main control board.
Samet E08: Door lock safety interlock fault in Washing Machine; door switch contact fails to close or open.
Laundry is heavily bundled on one side of the drum, preventing the machine from reaching spin speed.
Stop the machine, open the door, and redistribute the laundry more evenly inside the drum. Restart the spin cycle.
Samet E8: Operational cycle fault detected during Refrigerator / Freezer program execution.
The sensor for the automatic ice maker is malfunctioning.
Check the sensor and its wiring. The entire ice maker assembly may need to be replaced.
Ice maker mechanical fault
The ice maker mechanism is jammed or has failed.
Check for any ice blockages. The ice maker motor or gearbox may have failed and requires replacement.
Main power supply voltage out of range
The incoming voltage to the machine is too low or too high for safe operation.
Check the household electrical supply. The error may clear if the power supply stabilizes. If it persists, consult an electrician.
Foam detected during drain
Too much detergent has been used, creating excessive foam that the machine cannot pump out effectively.
Run a rinse and spin cycle to clear the foam. Use less detergent in future washes, especially with soft water.
Cookware not detected (flashing)
The pan is not suitable for induction, is too small, or is not centered on the cooking zone.
Use cookware made of a ferromagnetic material (a magnet should stick to the base). Ensure the pan's base is flat and covers the majority of the cooking zone.
Oven temperature sensor error (Open circuit)
The oven's NTC temperature sensor is disconnected or has failed.
Check the connection of the sensor to the control board. Test the sensor's resistance; replace if it shows an open circuit.
Water overflow detected / Anti-flood activated
A leak has been detected in the base of the dishwasher, activating the flood protection switch.
Disconnect from power. Tilt the dishwasher to drain water from the base. Find and repair the source of the leak (e.g., hose, seal).
Oven temperature sensor error (Short circuit)
The oven's NTC temperature sensor has short-circuited.
Test the resistance of the NTC sensor. If it shows a short circuit (near zero ohms), it needs to be replaced.
Samet F2: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.
Clogged filters, kinked drain hose, or a faulty drain pump.
Clean the filters inside the dishwasher. Check the drain hose for blockages. Inspect the drain pump impeller for debris.
Samet F03: NTC temperature sensor signal out of range (open or short circuit) in Oven / Microwave.
The oven has exceeded its maximum safe temperature, possibly due to a stuck relay on the control board or faulty sensor.
Disconnect power immediately. Check the cooling fan for operation. Test the NTC sensor. The main board may need replacement.
Samet F3: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level.
The water inlet valve is stuck open, or the flow meter is malfunctioning.
Turn off the water supply. This error usually requires replacing the water inlet valve assembly.
Door lock mechanism fault
The motorized door lock for the pyrolytic cleaning cycle is jammed or has failed.
Check for any obstructions around the door lock. The door lock motor assembly may need to be replaced.
Samet F05: Operational cycle fault detected during Oven / Microwave program execution.
Communication failure between the main control board and the display board.
Check the ribbon cable and wiring connections between the two electronic boards. If connections are good, one of the boards is likely faulty.
Our official certified partners service Samet appliances in your area.