V-Zug Error Codes & Diagnostics

V-ZUG AdoraWash / Unimatic V2000-V6000 Swiss Precision Washer: Inverter DC bus rail voltage anomaly F05; excessive AC ripple voltage or unstable DC rail (>340V or <220V DC) detected on drive PCB.

On V-ZUG washing machines featuring AdoraWash vibration absorbing system (VAS), OptiTime energy logic, and brushless synchronous inverter drive: Degraded high-voltage electrolytic filter capacitors, dry solder joints on rectifier bridge, or AC line noise.

Sensor fault on cooking zone. Diagnostic error code F5 reported on V-Zug Hob.

On V-Zug Hob: The temperature sensor for a specific cooking zone is faulty.

V-ZUG AdoraWash / Unimatic V2000-V6000 Swiss Precision Washer: Door interlock sensor anomaly F06; controller measures abnormal PTC heater pill resistance, preventing latch cycle engagement.

On V-ZUG washing machines utilizing AdoraWash vibration absorbing system (VAS), OptiTime energy logic, and brushless synchronous inverter drive: Degraded bimetal PTC pellet inside door lock, cracked internal contacts, or burnt lock control triac.

On V-Zug Oven: Door lock error / Pyrolytic cleaning fault

On V-Zug Oven: The door could not be locked or unlocked, often during a self-cleaning cycle.

V-Zug F08: Water/air heating failure in Washing Machine; heating circuit does not reach set temperature.

On V-Zug Washing Machine: The relay that controls the heating element is stuck in the on position on the main control board.

On V-Zug Hob: Incorrect cookware or no cookware detected

On V-Zug Hob: The pan is not suitable for induction, is too small for the cooking zone, or is not positioned correctly. Or, no pan is on the zone.

V-Zug F13: Motor drive or inverter rotation anomaly in Dishwasher; drum/motor fails to spin at target RPM.

On V-Zug Dishwasher: The water distributor (alternating spray arm motor) is blocked or defective.

Electronic control board error. Diagnostic error code F14 reported on V-Zug Washing Machine.

On V-Zug Washing Machine: The main electronic control board has an internal fault or has failed.

V-Zug F22: Operational cycle fault detected during Dishwasher program execution.

On V-Zug Dishwasher: The pressure sensor (analogue) is providing an out-of-range reading, indicating a fault with the sensor itself or a blockage in its tubing.

V-Zug I10: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level.

On V-Zug Dishwasher: No water is entering the appliance. The tap may be closed, the inlet hose kinked, or the filter blocked.

V-Zug I20: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.

On V-Zug Dishwasher: Water is not being pumped out correctly. The filters are dirty, the drain hose is blocked or kinked, or the drain pump is jammed.

Anti-flood system activated. Diagnostic error code i30 reported on V-Zug Dishwasher.

On V-Zug Dishwasher: Water has leaked into the base of the dishwasher, tripping the safety float switch.

Wash pump or circulation pump fault. Diagnostic error code i50 reported on V-Zug Dishwasher.

On V-Zug Dishwasher: The circulation pump motor is drawing too much current or is not running. It could be blocked or electronically faulty.

V-Zug I60: NTC temperature sensor signal out of range (open or short circuit) in Dishwasher.

On V-Zug Dishwasher: The water is not heating up. This can be caused by a faulty heating element, a defective NTC temperature sensor, or a problem on the main control board.

V-Zug IC0: Operational cycle fault detected during Dishwasher program execution.

On V-Zug Dishwasher: A communication breakdown has occurred between the main control unit and the user interface or other components.