OEM VERIFIED BENCH

OFFICIAL FAULT CODEi24

Arthur Martin // OFFICIAL DIAGNOSTIC BENCH

Arthur Martin i24

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code i24:ElectroluxI24 AEGI24 ZanussiI24 CastorI24 FaureI24 FrigidaireI24 KelvinatorI24 WestinghouseI24 ZoppasI24

Symptom / Description

FAULT

Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher: Drain pump circuit feedback incongruence i24; drain pump current draws outside operating window.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Arthur Martin (Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher) models: Pump running dry with zero hydraulic load (airlock), broken impeller decoupled from shaft, or high-resistance spade terminal connection.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Verify impeller is firmly fixed to motor shaft. Pour 2 liters of water into sump to prime pump cavity. Check spade crimp terminals. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Arthur Martin Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Arthur Martin I24

FAQ TREE

What does error code I24 mean on a Arthur Martin appliance?

Arthur Martin error code I24 indicates: Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher: Drain pump circuit feedback incongruence i24; drain pump current draws outside operating window..

What is the root cause of Arthur Martin error code I24?

The primary root cause for Arthur Martin code I24 is: On Arthur Martin (Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher) models: Pump running dry with zero hydraulic load (airlock), broken impeller decoupled from shaft, or high-resistance spade terminal connection..

How do I fix or resolve Arthur Martin error code I24?

To resolve error code I24: Verify impeller is firmly fixed to motor shaft. Pour 2 liters of water into sump to prime pump cavity. Check spade crimp terminals. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

Is it safe to clear Arthur Martin error code I24 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Arthur Martin code I24 persists, the physical component causing On Arthur Martin (Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher) models: Pump running dry with zero hydraulic load (airlock), broken impeller decoupled from shaft, or high-resistance spade terminal connection. must be inspected or replaced.

How do I test electrical resistance for Arthur Martin code I24 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Arthur Martin code I24?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEi24

Arthur Martin // OFFICIAL DIAGNOSTIC BENCH

Arthur Martin i24

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code i24:ElectroluxI24 AEGI24 ZanussiI24 CastorI24 FaureI24 FrigidaireI24 KelvinatorI24 WestinghouseI24 ZoppasI24

Symptom / Description

FAULT

Arthur Martin ASF Series / Calypso / Electrolux Luxe Dishwasher: Drain pump circuit feedback incongruence i24; drain pump current draws outside operating window.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Arthur Martin Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Arthur Martin I24

FAQ TREE

What does error code I24 mean on a Arthur Martin appliance?

What is the root cause of Arthur Martin error code I24?

How do I fix or resolve Arthur Martin error code I24?

Is it safe to clear Arthur Martin error code I24 by resetting power?

How do I test electrical resistance for Arthur Martin code I24 using a multimeter?

What safety protocol must be followed before servicing Arthur Martin code I24?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Arthur Martin i24

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Arthur Martin I24

Community Verification

Related Arthur Martin Dishwasher Error Codes

Arthur Martin i24

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Arthur Martin I24

Community Verification

Related Arthur Martin Dishwasher Error Codes