OEM VERIFIED BENCH

OFFICIAL FAULT CODEi56

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure i56

DishwasherNTC Temperature Sensor & Thermistor

Dishwasher

Other Brands Sharing Code i56:ElectroluxI56 AEGI56 ZanussiI56 Arthur MartinI56 CastorI56 FrigidaireI56 KelvinatorI56 WestinghouseI56 ZoppasI56

Symptom / Description

FAULT

Faure FDF Series / Clean&Dry / MaxiWash Dishwasher: Circulation pump inverter thermal cutoff / motor overheating i56; internal thermistor exceeds safety cutoff.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Faure (Faure FDF Series / Clean&Dry / MaxiWash Dishwasher) models: Extended cycle with hot water intake (> 65°C), inadequate motor cooling in enclosed bottom base, or heavy bearing friction.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Allow motor to cool down for 30 minutes. Check inlet water temperature (max 60°C). Inspect motor bearings for friction or seizing. Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure I56

FAQ TREE

What does error code I56 mean on a Faure appliance?

Faure error code I56 indicates: Faure FDF Series / Clean&Dry / MaxiWash Dishwasher: Circulation pump inverter thermal cutoff / motor overheating i56; internal thermistor exceeds safety cutoff..

What is the root cause of Faure error code I56?

The primary root cause for Faure code I56 is: On Faure (Faure FDF Series / Clean&Dry / MaxiWash Dishwasher) models: Extended cycle with hot water intake (> 65°C), inadequate motor cooling in enclosed bottom base, or heavy bearing friction..

How do I fix or resolve Faure error code I56?

To resolve error code I56: Allow motor to cool down for 30 minutes. Check inlet water temperature (max 60°C). Inspect motor bearings for friction or seizing. Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

Is it safe to clear Faure error code I56 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Faure code I56 persists, the physical component causing On Faure (Faure FDF Series / Clean&Dry / MaxiWash Dishwasher) models: Extended cycle with hot water intake (> 65°C), inadequate motor cooling in enclosed bottom base, or heavy bearing friction. must be inspected or replaced.

How do I test electrical resistance for Faure code I56 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

What safety protocol must be followed before servicing Faure code I56?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEi56

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure i56

DishwasherNTC Temperature Sensor & Thermistor

Dishwasher

Other Brands Sharing Code i56:ElectroluxI56 AEGI56 ZanussiI56 Arthur MartinI56 CastorI56 FrigidaireI56 KelvinatorI56 WestinghouseI56 ZoppasI56

Symptom / Description

FAULT

Faure FDF Series / Clean&Dry / MaxiWash Dishwasher: Circulation pump inverter thermal cutoff / motor overheating i56; internal thermistor exceeds safety cutoff.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Faure (Faure FDF Series / Clean&Dry / MaxiWash Dishwasher) models: Extended cycle with hot water intake (> 65°C), inadequate motor cooling in enclosed bottom base, or heavy bearing friction.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure I56

FAQ TREE

What does error code I56 mean on a Faure appliance?

Faure error code I56 indicates: Faure FDF Series / Clean&Dry / MaxiWash Dishwasher: Circulation pump inverter thermal cutoff / motor overheating i56; internal thermistor exceeds safety cutoff..

What is the root cause of Faure error code I56?

How do I fix or resolve Faure error code I56?

Is it safe to clear Faure error code I56 by resetting power?

How do I test electrical resistance for Faure code I56 using a multimeter?

What safety protocol must be followed before servicing Faure code I56?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Faure i56

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure I56

Community Verification

Related Faure Dishwasher Error Codes

Faure i56

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure I56

Community Verification

Related Faure Dishwasher Error Codes