OEM VERIFIED BENCH

OFFICIAL FAULT CODEF25

Ignis // OFFICIAL DIAGNOSTIC BENCH

Ignis F25

HobNTC Temperature Sensor & Thermistor

Integrated luxury convection oven and induction cooktop with illuminated touch controls

Hob

Other Brands Sharing Code F25:BoschF25 MieleF25 SiemensF25 WhirlpoolF25 IndesitF25 BauknechtF25 NeffF25 AristonF25 GaggenauF25 AmanaF25

Symptom / Description

FAULT

Ignis Platino Induction & Ceramic Cooktop: Rear induction zone center temperature sensor disconnect F25; glass ceramic sensor spring probe circuit open.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Ignis cooktops: Broken copper wire at coil center spring eyelet, oxidized plug on generator board, or cracked ceramic thermistor chip.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Unclip glass top and access rear induction coil. Measure center spring NTC probe resistance (nominal ~100 kΩ at 25°C). Replace central coil sensor. Power down at breaker switch for 60 seconds, wipe surface dry with microfiber cloth, then restart.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ignis Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorHob / Cooktop

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ignis F25

FAQ TREE

What does error code F25 mean on a Ignis appliance?

Ignis error code F25 indicates: Ignis Platino Induction & Ceramic Cooktop: Rear induction zone center temperature sensor disconnect F25; glass ceramic sensor spring probe circuit open..

What is the root cause of Ignis error code F25?

The primary root cause for Ignis code F25 is: On Ignis cooktops: Broken copper wire at coil center spring eyelet, oxidized plug on generator board, or cracked ceramic thermistor chip..

How do I fix or resolve Ignis error code F25?

To resolve error code F25: Unclip glass top and access rear induction coil. Measure center spring NTC probe resistance (nominal ~100 kΩ at 25°C). Replace central coil sensor. Power down at breaker switch for 60 seconds, wipe surface dry with microfiber cloth, then restart.

Is it safe to clear Ignis error code F25 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Ignis code F25 persists, the physical component causing On Ignis cooktops: Broken copper wire at coil center spring eyelet, oxidized plug on generator board, or cracked ceramic thermistor chip. must be inspected or replaced.

How do I test electrical resistance for Ignis code F25 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

What safety protocol must be followed before servicing Ignis code F25?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEF25

Ignis // OFFICIAL DIAGNOSTIC BENCH

Ignis F25

HobNTC Temperature Sensor & Thermistor

Hob

Other Brands Sharing Code F25:BoschF25 MieleF25 SiemensF25 WhirlpoolF25 IndesitF25 BauknechtF25 NeffF25 AristonF25 GaggenauF25 AmanaF25

Symptom / Description

FAULT

Ignis Platino Induction & Ceramic Cooktop: Rear induction zone center temperature sensor disconnect F25; glass ceramic sensor spring probe circuit open.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Ignis cooktops: Broken copper wire at coil center spring eyelet, oxidized plug on generator board, or cracked ceramic thermistor chip.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ignis Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorHob / Cooktop

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ignis F25

FAQ TREE

What does error code F25 mean on a Ignis appliance?

Ignis error code F25 indicates: Ignis Platino Induction & Ceramic Cooktop: Rear induction zone center temperature sensor disconnect F25; glass ceramic sensor spring probe circuit open..

What is the root cause of Ignis error code F25?

The primary root cause for Ignis code F25 is: On Ignis cooktops: Broken copper wire at coil center spring eyelet, oxidized plug on generator board, or cracked ceramic thermistor chip..

How do I fix or resolve Ignis error code F25?

Is it safe to clear Ignis error code F25 by resetting power?

How do I test electrical resistance for Ignis code F25 using a multimeter?

What safety protocol must be followed before servicing Ignis code F25?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Ignis F25

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ignis F25

Community Verification

Related Ignis Hob / Cooktop Error Codes

Ignis F25

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ignis F25

Community Verification

Related Ignis Hob / Cooktop Error Codes