OEM VERIFIED BENCH

OFFICIAL FAULT CODEUV

Ignis // OFFICIAL DIAGNOSTIC BENCH

Ignis Refrigerator / Freezer UV

Q: What does error code UV mean on a Ignis appliance?

Ignis error code UV indicates: Ignis Tutti i Giorni No-Frost Refrigerator / Freezer: Diagnostic code UV indicates inverter driver DC link under-voltage trip; compressor cannot maintain required torque..

Q: What is the root cause of Ignis error code UV?

The primary root cause for Ignis code UV is: On Ignis refrigerators (Ignis Tutti i Giorni reliable electro-mechanical and digital platform architecture): Grid brownout drop below 180V AC, high-resistance wall outlet plug, or dried-out electrolytic reservoir capacitors (< 210V DC bus)..

Q: How do I fix or resolve Ignis error code UV?

To resolve error code UV: Verify line voltage under compressor startup load (min 207V AC). Check DC bus voltage on inverter board (trip occurs below 210V DC). Replace inverter board if supply is 230V AC. Press and hold Alarm/Reset button for 5 seconds until the acoustic chime silences and display stabilizes.

Q: Is it safe to clear Ignis error code UV by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Ignis code UV persists, the physical component causing On Ignis refrigerators (Ignis Tutti i Giorni reliable electro-mechanical and digital platform architecture): Grid brownout drop below 180V AC, high-resistance wall outlet plug, or dried-out electrolytic reservoir capacitors (< 210V DC bus). must be inspected or replaced.

Q: How do I test electrical resistance for Ignis code UV using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Compressor Motor Windings (Run/Start) & Defrost Heater across Across 3 compressor pins (Common, Run, Start): R(C-S) + R(C-R) = R(S-R). Winding to earth: >20MΩ (OL).. Expected nominal reading is 15Ω–25Ω (Run C-R), 20Ω–35Ω (Start C-S), 200Ω–400Ω (Defrost Heater). PTC Relay: 10Ω–30Ω at 25°C.. Tolerance: ±10%. Any low insulation resistance to casing (<2MΩ) trips the breaker. Defrost bimetal reads <0.5Ω when sub-zero..

Q: What safety protocol must be followed before servicing Ignis code UV?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Refrigerator / FreezerRefrigeration Compressor, Defrost Heater & PTC Relay

Monolithic French-door smart refrigerator in matte black steel with dual refrigeration zones

Refrigerator / Freezer

Whirlpool / Indesit Group: Equivalent Code Across OEM Group Brands

Whirlpool / Indesit Global Electronic Architecture

WhirlpoolUV IndesitUV AristonUV HotpointUV BauknechtUV MaytagUV

Other Brands Sharing Code UV:ScholtèsUV AmanaUV KitchenaidUV

Symptom / Description

FAULT

Ignis Tutti i Giorni No-Frost Refrigerator / Freezer: Diagnostic code UV indicates inverter driver DC link under-voltage trip; compressor cannot maintain required torque.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Ignis refrigerators (Ignis Tutti i Giorni reliable electro-mechanical and digital platform architecture): Grid brownout drop below 180V AC, high-resistance wall outlet plug, or dried-out electrolytic reservoir capacitors (< 210V DC bus).

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Verify line voltage under compressor startup load (min 207V AC). Check DC bus voltage on inverter board (trip occurs below 210V DC). Replace inverter board if supply is 230V AC. Press and hold Alarm/Reset button for 5 seconds until the acoustic chime silences and display stabilizes.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ignis Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

SWISS ATELIER TECHNICAL BLUEPRINT // 2026 SCHEMATIC STANDARD

Main Control PCB, Refrigeration & Sensor Bus Loop

230V AC Mains Filter, Low-Voltage SMPS DC Rails & MCU I2C/UART Bus

CALIBRATED TEST POINTS (TP1 / TP2)

ACTIVE MULTIMETER BENCH

Target Component

Compressor Motor Windings (Run/Start) & Defrost Heater

Nominal Resistance / Test Range

15Ω–25Ω (Run C-R), 20Ω–35Ω (Start C-S), 200Ω–400Ω (Defrost Heater). PTC Relay: 10Ω–30Ω at 25°C.

Test Harness Pins

Across 3 compressor pins (Common, Run, Start): R(C-S) + R(C-R) = R(S-R). Winding to earth: >20MΩ (OL).

Diagnostic Verification Rule

Verify clean DC rails without ripple. Defective SMPS capacitors or burned MCU comm bus triggers system lock.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLRefrigeration Compressor, Defrost Heater & PTC RelayRefrigerator / Freezer

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

15Ω–25Ω (Run C-R), 20Ω–35Ω (Start C-S), 200Ω–400Ω (Defrost Heater). PTC Relay: 10Ω–30Ω at 25°C.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Compressor Motor Windings (Run/Start) & Defrost Heater

Test Pins & Connections

PROBE (+)

PROBE (-)

Across 3 compressor pins (Common, Run, Start): R(C-S) + R(C-R) = R(S-R). Winding to earth: >20MΩ (OL).

Tolerance & Diagnostic Criteria±10%. Any low insulation resistance to casing (<2MΩ) trips the breaker. Defrost bimetal reads <0.5Ω when sub-zero.

1. Pre-Intervention Electrical Safety Protocols

!Refrigeration Safety Protocol: Disconnect mains power before unclipping compressor terminal covers.
!Flammable Refrigerant Warning: R600a (isobutane) is flammable. Never puncture cooling tubes or use open flame.
!High Surface Temperature: Compressor shell can exceed 80°C during normal operation. Allow to cool before inspection.

3. Preliminary Mechanical & Visual Checks

Listen for compressor startup attempts: repetitive clicking every 60 seconds indicates locked rotor or failed PTC relay.
Inspect evaporator coil for thick solid frost buildup, signaling defrost heater, sensor, or timer failure.
Clean condenser coils and check cooling fan motor for free rotation and dust accumulation.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ignis UV

FAQ TREE

What does error code UV mean on a Ignis appliance?

Ignis error code UV indicates: Ignis Tutti i Giorni No-Frost Refrigerator / Freezer: Diagnostic code UV indicates inverter driver DC link under-voltage trip; compressor cannot maintain required torque..

What is the root cause of Ignis error code UV?

The primary root cause for Ignis code UV is: On Ignis refrigerators (Ignis Tutti i Giorni reliable electro-mechanical and digital platform architecture): Grid brownout drop below 180V AC, high-resistance wall outlet plug, or dried-out electrolytic reservoir capacitors (< 210V DC bus)..

How do I fix or resolve Ignis error code UV?

To resolve error code UV: Verify line voltage under compressor startup load (min 207V AC). Check DC bus voltage on inverter board (trip occurs below 210V DC). Replace inverter board if supply is 230V AC. Press and hold Alarm/Reset button for 5 seconds until the acoustic chime silences and display stabilizes.

Is it safe to clear Ignis error code UV by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Ignis code UV persists, the physical component causing On Ignis refrigerators (Ignis Tutti i Giorni reliable electro-mechanical and digital platform architecture): Grid brownout drop below 180V AC, high-resistance wall outlet plug, or dried-out electrolytic reservoir capacitors (< 210V DC bus). must be inspected or replaced.

How do I test electrical resistance for Ignis code UV using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Compressor Motor Windings (Run/Start) & Defrost Heater across Across 3 compressor pins (Common, Run, Start): R(C-S) + R(C-R) = R(S-R). Winding to earth: >20MΩ (OL).. Expected nominal reading is 15Ω–25Ω (Run C-R), 20Ω–35Ω (Start C-S), 200Ω–400Ω (Defrost Heater). PTC Relay: 10Ω–30Ω at 25°C.. Tolerance: ±10%. Any low insulation resistance to casing (<2MΩ) trips the breaker. Defrost bimetal reads <0.5Ω when sub-zero..

What safety protocol must be followed before servicing Ignis code UV?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEUV

Ignis // OFFICIAL DIAGNOSTIC BENCH

Ignis Refrigerator / Freezer UV

Refrigerator / FreezerRefrigeration Compressor, Defrost Heater & PTC Relay

Refrigerator / Freezer

Whirlpool / Indesit Group: Equivalent Code Across OEM Group Brands

Whirlpool / Indesit Global Electronic Architecture

WhirlpoolUV IndesitUV AristonUV HotpointUV BauknechtUV MaytagUV

Other Brands Sharing Code UV:ScholtèsUV AmanaUV KitchenaidUV

Symptom / Description

FAULT

Ignis Tutti i Giorni No-Frost Refrigerator / Freezer: Diagnostic code UV indicates inverter driver DC link under-voltage trip; compressor cannot maintain required torque.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Ignis Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

SWISS ATELIER TECHNICAL BLUEPRINT // 2026 SCHEMATIC STANDARD

Main Control PCB, Refrigeration & Sensor Bus Loop

230V AC Mains Filter, Low-Voltage SMPS DC Rails & MCU I2C/UART Bus

CALIBRATED TEST POINTS (TP1 / TP2)

ACTIVE MULTIMETER BENCH

Target Component

Compressor Motor Windings (Run/Start) & Defrost Heater

Nominal Resistance / Test Range

15Ω–25Ω (Run C-R), 20Ω–35Ω (Start C-S), 200Ω–400Ω (Defrost Heater). PTC Relay: 10Ω–30Ω at 25°C.

Test Harness Pins

Across 3 compressor pins (Common, Run, Start): R(C-S) + R(C-R) = R(S-R). Winding to earth: >20MΩ (OL).

Diagnostic Verification Rule

Verify clean DC rails without ripple. Defective SMPS capacitors or burned MCU comm bus triggers system lock.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLRefrigeration Compressor, Defrost Heater & PTC RelayRefrigerator / Freezer

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

15Ω–25Ω (Run C-R), 20Ω–35Ω (Start C-S), 200Ω–400Ω (Defrost Heater). PTC Relay: 10Ω–30Ω at 25°C.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Compressor Motor Windings (Run/Start) & Defrost Heater

Test Pins & Connections

PROBE (+)

PROBE (-)

Across 3 compressor pins (Common, Run, Start): R(C-S) + R(C-R) = R(S-R). Winding to earth: >20MΩ (OL).

Tolerance & Diagnostic Criteria±10%. Any low insulation resistance to casing (<2MΩ) trips the breaker. Defrost bimetal reads <0.5Ω when sub-zero.

1. Pre-Intervention Electrical Safety Protocols

!Refrigeration Safety Protocol: Disconnect mains power before unclipping compressor terminal covers.
!Flammable Refrigerant Warning: R600a (isobutane) is flammable. Never puncture cooling tubes or use open flame.
!High Surface Temperature: Compressor shell can exceed 80°C during normal operation. Allow to cool before inspection.

3. Preliminary Mechanical & Visual Checks

Listen for compressor startup attempts: repetitive clicking every 60 seconds indicates locked rotor or failed PTC relay.
Inspect evaporator coil for thick solid frost buildup, signaling defrost heater, sensor, or timer failure.
Clean condenser coils and check cooling fan motor for free rotation and dust accumulation.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Ignis UV

FAQ TREE

What does error code UV mean on a Ignis appliance?

What is the root cause of Ignis error code UV?

How do I fix or resolve Ignis error code UV?

Is it safe to clear Ignis error code UV by resetting power?

How do I test electrical resistance for Ignis code UV using a multimeter?

What safety protocol must be followed before servicing Ignis code UV?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Ignis Refrigerator / Freezer UV

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Main Control PCB, Refrigeration & Sensor Bus Loop

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ignis UV

Community Verification

Related Ignis Refrigerator / Freezer Error Codes

Ignis Refrigerator / Freezer UV

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Main Control PCB, Refrigeration & Sensor Bus Loop

Workshop Verification & Safety Checklist

Frequently Asked Questions: Ignis UV

Community Verification

Related Ignis Refrigerator / Freezer Error Codes