OEM VERIFIED BENCH

OFFICIAL FAULT CODEd06

Sauter // OFFICIAL DIAGNOSTIC BENCH

Sauter d06

Q: What does error code D06 mean on a Sauter appliance?

Sauter error code D06 indicates: Sauter Silence / SVH / Saveurs Built-in Dishwasher: Wash motor overcurrent cutoff d06; power electronic controller trips due to excessive electric current draw by the circulation pump..

Q: What is the root cause of Sauter error code D06?

The primary root cause for Sauter code D06 is: On Sauter dishwashers featuring Saveurs alternating hydraulic wash arms, Flexi-Safe load geometry, and 42dB acoustic shielding: Foreign object (toothpick, seed) jamming the impeller volute, or shorted turns in stator winding..

Q: How do I fix or resolve Sauter error code D06?

To resolve error code D06: Disassemble wash pump volute and remove foreign debris. Measure running current with an ammeter clamp (<1.2A). Replace motor if shorted. Press and hold the Start/Reset button for 4 seconds until drain pump initiates, allow pumpout to complete, then switch off.

Q: Is it safe to clear Sauter error code D06 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Sauter code D06 persists, the physical component causing On Sauter dishwashers featuring Saveurs alternating hydraulic wash arms, Flexi-Safe load geometry, and 42dB acoustic shielding: Foreign object (toothpick, seed) jamming the impeller volute, or shorted turns in stator winding. must be inspected or replaced.

Q: How do I test electrical resistance for Sauter code D06 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

Q: What safety protocol must be followed before servicing Sauter code D06?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

DishwasherDrainage System & Drain Pump

Dishwasher

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code d06:BrandtD06 De DietrichD06 FAGORD06 OceanD06

Symptom / Description

FAULT

Sauter Silence / SVH / Saveurs Built-in Dishwasher: Wash motor overcurrent cutoff d06; power electronic controller trips due to excessive electric current draw by the circulation pump.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Sauter dishwashers featuring Saveurs alternating hydraulic wash arms, Flexi-Safe load geometry, and 42dB acoustic shielding: Foreign object (toothpick, seed) jamming the impeller volute, or shorted turns in stator winding.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Disassemble wash pump volute and remove foreign debris. Measure running current with an ammeter clamp (<1.2A). Replace motor if shorted. Press and hold the Start/Reset button for 4 seconds until drain pump initiates, allow pumpout to complete, then switch off.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Sauter Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Sauter D06

FAQ TREE

What does error code D06 mean on a Sauter appliance?

Sauter error code D06 indicates: Sauter Silence / SVH / Saveurs Built-in Dishwasher: Wash motor overcurrent cutoff d06; power electronic controller trips due to excessive electric current draw by the circulation pump..

What is the root cause of Sauter error code D06?

The primary root cause for Sauter code D06 is: On Sauter dishwashers featuring Saveurs alternating hydraulic wash arms, Flexi-Safe load geometry, and 42dB acoustic shielding: Foreign object (toothpick, seed) jamming the impeller volute, or shorted turns in stator winding..

How do I fix or resolve Sauter error code D06?

To resolve error code D06: Disassemble wash pump volute and remove foreign debris. Measure running current with an ammeter clamp (<1.2A). Replace motor if shorted. Press and hold the Start/Reset button for 4 seconds until drain pump initiates, allow pumpout to complete, then switch off.

Is it safe to clear Sauter error code D06 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Sauter code D06 persists, the physical component causing On Sauter dishwashers featuring Saveurs alternating hydraulic wash arms, Flexi-Safe load geometry, and 42dB acoustic shielding: Foreign object (toothpick, seed) jamming the impeller volute, or shorted turns in stator winding. must be inspected or replaced.

How do I test electrical resistance for Sauter code D06 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Sauter code D06?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEd06

Sauter // OFFICIAL DIAGNOSTIC BENCH

Sauter d06

DishwasherDrainage System & Drain Pump

Dishwasher

Select Appliance Type

0ms Instant Telemetry Switch

Other Brands Sharing Code d06:BrandtD06 De DietrichD06 FAGORD06 OceanD06

Symptom / Description

FAULT

Sauter Silence / SVH / Saveurs Built-in Dishwasher: Wash motor overcurrent cutoff d06; power electronic controller trips due to excessive electric current draw by the circulation pump.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Sauter Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Sauter D06

FAQ TREE

What does error code D06 mean on a Sauter appliance?

What is the root cause of Sauter error code D06?

How do I fix or resolve Sauter error code D06?

Is it safe to clear Sauter error code D06 by resetting power?

How do I test electrical resistance for Sauter code D06 using a multimeter?

What safety protocol must be followed before servicing Sauter code D06?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Sauter d06

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Sauter D06

Community Verification

Related Sauter Dishwasher Error Codes

Sauter d06

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Sauter D06

Community Verification

Related Sauter Dishwasher Error Codes