OEM VERIFIED BENCH

OFFICIAL FAULT CODEAL03

Sekom // OFFICIAL DIAGNOSTIC BENCH

Sekom AL03

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code AL03:BauknechtAL03 HooverAL03 ZanussiAL03 De DietrichAL03 GaggenauAL03 SchulthessAL03 FAGORAL03 RosieresAL03 AtlanticAL03 IgnisAL03

Symptom / Description

FAULT

Water Drain Timeout Error

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Alternative code for the appliance failing to drain water.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Clean the filters in the bottom of the tub. Check the drain hose for blockages. Inspect the drain pump impeller.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Sekom Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Sekom AL03

FAQ TREE

What does error code AL03 mean on a Sekom appliance?

Sekom error code AL03 indicates: Water Drain Timeout Error.

What is the root cause of Sekom error code AL03?

The primary root cause for Sekom code AL03 is: Alternative code for the appliance failing to drain water..

How do I fix or resolve Sekom error code AL03?

To resolve error code AL03: Clean the filters in the bottom of the tub. Check the drain hose for blockages. Inspect the drain pump impeller.

Is it safe to clear Sekom error code AL03 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Sekom code AL03 persists, the physical component causing Alternative code for the appliance failing to drain water. must be inspected or replaced.

How do I test electrical resistance for Sekom code AL03 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Sekom code AL03?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEAL03

Sekom // OFFICIAL DIAGNOSTIC BENCH

Sekom AL03

DishwasherDrainage System & Drain Pump

Dishwasher

Other Brands Sharing Code AL03:BauknechtAL03 HooverAL03 ZanussiAL03 De DietrichAL03 GaggenauAL03 SchulthessAL03 FAGORAL03 RosieresAL03 AtlanticAL03 IgnisAL03

Symptom / Description

FAULT

Water Drain Timeout Error

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Alternative code for the appliance failing to drain water.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Clean the filters in the bottom of the tub. Check the drain hose for blockages. Inspect the drain pump impeller.

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Sekom Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Sekom AL03

FAQ TREE

What does error code AL03 mean on a Sekom appliance?

Sekom error code AL03 indicates: Water Drain Timeout Error.

What is the root cause of Sekom error code AL03?

The primary root cause for Sekom code AL03 is: Alternative code for the appliance failing to drain water..

How do I fix or resolve Sekom error code AL03?

To resolve error code AL03: Clean the filters in the bottom of the tub. Check the drain hose for blockages. Inspect the drain pump impeller.

Is it safe to clear Sekom error code AL03 by resetting power?

How do I test electrical resistance for Sekom code AL03 using a multimeter?

What safety protocol must be followed before servicing Sekom code AL03?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Sekom AL03

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Sekom AL03

Community Verification

Related Sekom Dishwasher Error Codes

Sekom AL03

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Sekom AL03

Community Verification

Related Sekom Dishwasher Error Codes