Access our premium database of error codes, common faults, and professional repair solutions for Electroline appliances.
Electroline E01: Door lock safety interlock fault in Washing Machine; door switch contact fails to close or open.
The machine's door is not properly closed or the door lock mechanism is faulty.
Ensure the door is firmly shut. Check the door lock switch and wiring for damage. Replace the door lock assembly if necessary.
Electroline E1: NTC temperature sensor signal out of range (open or short circuit) in Refrigerator / Freezer.
The temperature sensor (thermistor) in the freezer compartment is faulty (open or short circuit).
Test the sensor's resistance. A reading that is infinite or near zero indicates a fault. Replace the freezer sensor.
Electroline E02: Water level pressure sensor/switch frequency anomaly detected in Washing Machine.
The machine is not filling with water, or the water level is too low after the filling time has elapsed.
Check that the water supply tap is fully open. Inspect the inlet hose for kinks or blockages. Clean the filter in the inlet valve. Test the inlet valve solenoid.
Refrigerator Sensor Failure
The temperature sensor (thermistor) in the fresh food compartment is faulty (open or short circuit).
Test the sensor's resistance. If the reading is incorrect for the ambient temperature, replace the refrigerator sensor.
Electroline E03: Water drainage failure detected in Washing Machine; drain pump cannot evacuate water within safety time limit.
The machine has failed to drain the water from the drum within the allowed time.
Check the drain filter for obstructions. Inspect the drain hose for kinks or blockages. Check the drain pump for blockages or failure.
Electroline E04: Water level pressure sensor/switch frequency anomaly detected in Washing Machine.
Too much water has entered the drum, or a leak has been detected in the base, activating the anti-flood switch.
Check the water inlet valve to see if it's stuck open. Inspect the pressure switch and its hose for blockages or damage. If leaking, find and repair the source of the leak.
Electroline E4: Cooling circuit or defrost system anomaly in Refrigerator / Freezer; compartment temperature deviation.
The defrost system is not working, leading to ice buildup on the evaporator coils.
Manually defrost the unit. Test the defrost heater and defrost thermal fuse for continuity. Replace the faulty component.
Electroline E05: NTC temperature sensor signal out of range (open or short circuit) in Washing Machine.
The water is not reaching the correct temperature. This is likely due to a faulty heating element or NTC temperature sensor.
Test the heating element for continuity. Check the NTC sensor's resistance. Inspect wiring to both components.
Electroline E06: Motor drive or inverter rotation anomaly in Washing Machine; drum/motor fails to spin at target RPM.
The motor is not turning or is not receiving the correct signals. Often caused by worn carbon brushes or a faulty tacho coil.
Inspect and replace worn motor carbon brushes. Check the motor tacho coil for continuity. Inspect the motor wiring and connections to the main control board.
Electroline E08: Door lock safety interlock fault in Washing Machine; door switch contact fails to close or open.
The machine has detected an uneven distribution of laundry in the drum during a spin cycle.
Stop the machine, open the door, and redistribute the laundry more evenly. Restart the spin cycle. Avoid washing single heavy items.
Electroline F1: Water drainage failure detected in Dishwasher; drain pump cannot evacuate water within safety time limit.
The anti-flood switch in the base of the dishwasher has been activated by a water leak.
Disconnect power. Carefully tip the appliance to drain water from the base. Locate and repair the source of the leak (e.g., hose, seal, pump).
Oven Temperature Sensor Fault
The oven's temperature sensor (probe/thermistor) is short-circuited or has failed.
Disconnect power and test the sensor's resistance at room temperature. Compare with manufacturer specs and replace if faulty.
Electroline F3: Operational cycle fault detected during Oven / Microwave program execution.
The main control board cannot communicate with the display board or other electronic components.
Check all wiring harnesses and connections between the electronic boards for loose or damaged wires. The main board may need replacement.
Electroline F4: Motor drive or inverter rotation anomaly in Oven / Microwave; drum/motor fails to spin at target RPM.
The motorized door lock for the self-clean cycle is not working correctly.
Check the door lock motor and switches for physical damage or electrical failure. The assembly may need to be replaced.
Electroline F5: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level.
The dishwasher has failed to fill with a sufficient amount of water.
Ensure the water supply tap is fully on. Check the inlet hose for kinks. Clean the mesh filter inside the inlet hose connection.
Heating Sensor (NTC) Fault
The NTC temperature sensor has an open circuit, indicating it is faulty.
Test the NTC sensor with a multimeter. If faulty, replace the sensor.
Electroline F8: Water/air heating failure in Dishwasher; heating circuit does not reach set temperature.
The dishwasher is not heating the water, likely due to a failed heating element.
Check the heating element for continuity using a multimeter. Replace the element if it is open circuit.
Electroline F9: Motor drive or inverter rotation anomaly in Dishwasher; drum/motor fails to spin at target RPM.
The diverter valve, which directs water to the spray arms, is not in the correct position or is jammed.
Inspect the diverter valve and its motor for blockages or damage. The assembly may need to be cleaned or replaced.
Our official certified partners service Electroline appliances in your area.