Access our premium database of error codes, common faults, and professional repair solutions for Siltal appliances.
Machine stops mid-cycle with water in the drum
General drainage fault. This is a common code on many brands Siltal manufactured for, indicating a blocked filter, pump, or hose.
Unplug the machine. Place a towel down and drain water via the filter housing. Unscrew and clean the filter. Check pump impeller and drain hose for obstructions.
Oven not heating or temperature inaccurate
The oven temperature sensor (NTC) has an open circuit, meaning it's failed or the wiring is broken.
Test the NTC sensor for resistance (should be ~500-600 Ohms at room temp). Check wiring. Replace the sensor if faulty.
Fridge section not cooling correctly, alarm may sound
The temperature sensor (NTC) for the refrigerator compartment is faulty (open or short circuit).
Locate the sensor in the fridge section. Test its resistance and check wiring. Replace the sensor if the reading is incorrect.
Oven overheats or displays incorrect high temperature
The oven temperature sensor (NTC) has a short circuit.
Test the NTC sensor for a very low or zero resistance reading. Replace the sensor if it is shorted.
Freezer section temperature is incorrect, alarm may sound
The temperature sensor (NTC) for the freezer compartment is faulty.
Locate the sensor in the freezer section. Test its resistance against a temperature chart. Replace the sensor if it's out of specification.
Oven shuts down during use, possibly displaying 'STOP'
Overheating has been detected by the safety thermostat, or the main board has detected a temperature runaway condition.
Check that the cooling fan is operating correctly. Ensure oven ventilation is not blocked. Test the safety thermostat and NTC sensor.
Excessive frost buildup in the freezer, poor cooling
Failure in the automatic defrost system. This could be a faulty defrost heater, thermal fuse, or defrost sensor.
Manually defrost the appliance. Test each component of the defrost system (heater, fuse, sensor) for continuity/correct resistance. Replace the failed part.
Oven display is blank or unresponsive, controls don't work
Communication error between the main power board and the user interface/display board.
Check the wiring harness and connectors between the two control boards. A fault on either board can cause this error.
Fridge is not cold but freezer is working, unusual noise
The evaporator fan motor has failed. This fan circulates cold air from the freezer to the fridge.
Listen for the fan running. If it's silent or noisy, inspect it for ice obstruction. Test the fan motor and replace if it has failed.
Oven door will not lock or unlock, pyrolysis cycle won't start
The motorized door lock mechanism has failed, is jammed, or the microswitches are not registering correctly.
Inspect the door lock assembly for physical obstruction. Test the motor and microswitches. Replace the lock assembly if faulty.
Appliance not cooling efficiently, compressor runs constantly
The condenser fan motor (located near the compressor) has failed. This fan cools the condenser coils and compressor.
Check if the condenser fan is running. Clean the fan and coils of dust. Test the fan motor and replace it if it is faulty.
Oven is completely dead or displays error on power up
A critical failure has been detected on the main power board (PCB).
Visually inspect the board for damage. This error usually requires the replacement of the main control board.
Oven overheats and may shut down
The main cooling fan, which cools the electronics, has failed or is jammed.
Check if the cooling fan blade can spin freely. Test the fan motor for continuity. Replace the fan motor if it has failed.
Icemaker not producing ice
A fault has been detected with the automatic icemaker mechanism or its sensor.
Ensure the icemaker is turned on and water supply is connected. Check for ice blockages in the mold. The icemaker assembly may need to be tested and replaced.
Washing machine or dishwasher stops and will not drain
Drainage problem. Used by brands Siltal produced for (e.g., AEG/Electrolux platform). Indicates blocked filter/hose or faulty pump.
Clean the drain filter. Check the drain hose for any kinks or blockages. Ensure the pump impeller can turn freely. Test the pump.
Our official certified partners service Siltal appliances in your area.