OEM VERIFIED BENCH

OFFICIAL FAULT CODEi10

Airlux // OFFICIAL DIAGNOSTIC BENCH

Airlux i10

DishwasherWater Level Pressure Switch & Air Dome

Dishwasher

Other Brands Sharing Code i10:ElectroluxI10 AEGI10 V-ZugI10 ZanussiI10 Arthur MartinI10 SchulthessI10 CastorI10 FaureI10 FavoritI10 ForsI10

Symptom / Description

FAULT

Airlux I10: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

No water is entering the appliance. This can be due to a closed tap, kinked hose, or blocked inlet valve filter.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Verify the water supply tap is fully open. Straighten any kinks in the inlet hose. Unscrew the hose and clean the small mesh filter inside the connection.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Airlux Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Level Pressure Switch & Air DomeDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Mechanical Pressure Switch Contacts / Inductive Frequency Sensor

Test Pins & Connections

PROBE (+)

PROBE (-)

Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal

Tolerance & Diagnostic CriteriaMechanical switch contacts must transition cleanly on gentle breath pressure. Coil ~22Ω ±5%.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Cut 230V mains power before accessing the upper chassis or pressure switch terminals.
!Drain appliance tub completely before disconnecting pressure switch sensing hoses.
!Never blow high-pressure compressed air into electronic analog pressure sensors: internal diaphragms will rupture!

3. Preliminary Mechanical & Visual Checks

Disconnect the silicone pressure tube from the lower air trap and inspect for soap sludge, lint, or water blockage.
Inspect the flexible rubber hose along its entire length for pinholes, cracks, or loose clamp fit.
Thoroughly flush the lower compression chamber (air dome) with hot water to dissolve detergent buildup.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Airlux I10

FAQ TREE

What does error code I10 mean on a Airlux appliance?

Airlux error code I10 indicates: Airlux I10: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level..

What is the root cause of Airlux error code I10?

The primary root cause for Airlux code I10 is: No water is entering the appliance. This can be due to a closed tap, kinked hose, or blocked inlet valve filter..

How do I fix or resolve Airlux error code I10?

To resolve error code I10: Verify the water supply tap is fully open. Straighten any kinks in the inlet hose. Unscrew the hose and clean the small mesh filter inside the connection.

Is it safe to clear Airlux error code I10 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Airlux code I10 persists, the physical component causing No water is entering the appliance. This can be due to a closed tap, kinked hose, or blocked inlet valve filter. must be inspected or replaced.

How do I test electrical resistance for Airlux code I10 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Mechanical Pressure Switch Contacts / Inductive Frequency Sensor across Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal. Expected nominal reading is Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.. Tolerance: Mechanical switch contacts must transition cleanly on gentle breath pressure. Coil ~22Ω ±5%..

What safety protocol must be followed before servicing Airlux code I10?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEi10

Airlux // OFFICIAL DIAGNOSTIC BENCH

Airlux i10

DishwasherWater Level Pressure Switch & Air Dome

Dishwasher

Other Brands Sharing Code i10:ElectroluxI10 AEGI10 V-ZugI10 ZanussiI10 Arthur MartinI10 SchulthessI10 CastorI10 FaureI10 FavoritI10 ForsI10

Symptom / Description

FAULT

Airlux I10: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

No water is entering the appliance. This can be due to a closed tap, kinked hose, or blocked inlet valve filter.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Verify the water supply tap is fully open. Straighten any kinks in the inlet hose. Unscrew the hose and clean the small mesh filter inside the connection.

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Airlux Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Level Pressure Switch & Air DomeDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Mechanical Pressure Switch Contacts / Inductive Frequency Sensor

Test Pins & Connections

PROBE (+)

PROBE (-)

Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal

Tolerance & Diagnostic CriteriaMechanical switch contacts must transition cleanly on gentle breath pressure. Coil ~22Ω ±5%.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Cut 230V mains power before accessing the upper chassis or pressure switch terminals.
!Drain appliance tub completely before disconnecting pressure switch sensing hoses.
!Never blow high-pressure compressed air into electronic analog pressure sensors: internal diaphragms will rupture!

3. Preliminary Mechanical & Visual Checks

Disconnect the silicone pressure tube from the lower air trap and inspect for soap sludge, lint, or water blockage.
Inspect the flexible rubber hose along its entire length for pinholes, cracks, or loose clamp fit.
Thoroughly flush the lower compression chamber (air dome) with hot water to dissolve detergent buildup.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Airlux I10

FAQ TREE

What does error code I10 mean on a Airlux appliance?

Airlux error code I10 indicates: Airlux I10: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level..

What is the root cause of Airlux error code I10?

The primary root cause for Airlux code I10 is: No water is entering the appliance. This can be due to a closed tap, kinked hose, or blocked inlet valve filter..

How do I fix or resolve Airlux error code I10?

To resolve error code I10: Verify the water supply tap is fully open. Straighten any kinks in the inlet hose. Unscrew the hose and clean the small mesh filter inside the connection.

Is it safe to clear Airlux error code I10 by resetting power?

How do I test electrical resistance for Airlux code I10 using a multimeter?

What safety protocol must be followed before servicing Airlux code I10?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Airlux i10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Airlux I10

Community Verification

Related Airlux Dishwasher Error Codes

Airlux i10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Airlux I10

Community Verification

Related Airlux Dishwasher Error Codes