Access our premium database of error codes, common faults, and professional repair solutions for Airlux appliances.
Airlux AL01: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level.
The aquastop or flood protection system has been triggered by water in the base pan.
Unplug the appliance. Check all internal hoses, seals, and connections for the source of the leak. Dry the base pan to reset the sensor.
Inlet tube sensor malfunction
Component fatigue, sensor feedback out of tolerance, wiring harness connector discontinuity, or electronic control board glitch.
Inspect or replace the inlet tube sensor.
Outlet tube sensor malfunction
Component fatigue, sensor feedback out of tolerance, wiring harness connector discontinuity, or electronic control board glitch.
Inspect or replace outlet tube sensor.
Jumper cap malfunction protection
Defective PCB Power Supply Rails & DC Bus Filter Capacitors, open/short circuit in the wiring harness, or faulty connector on the electronic control board (pcb) & bus communications.
Check the jumper cap on the main PCB board. It may be missing or faulty.
Door cannot be locked or unlocked
The door lock mechanism is faulty, the wiring is damaged, or the main control board has an issue.
Check door is closed properly. Inspect the door lock mechanism and wiring. If the issue persists, the lock or PCB may need replacement. Power cycle the appliance first.
Refrigerant system high pressure protection
Ensure the ventilation underneath the hob is not blocked. Check if the internal cooling fan is working. Allow the hob to cool down completely before reuse.
Check refrigerant levels, ensure outdoor unit has proper airflow. PRO TIP: For communication (E6) and sensor errors, always check the wiring connections between the indoor and outdoor units or sensor harness before replacing parts.
Machine is not filling with water
The water supply is off, the inlet hose is kinked or blocked, or the water inlet valve has failed.
Ensure water tap is fully open. Check the inlet hose for kinks and the filter inside for debris. Test the inlet valve for functionality.
Evaporator anti-freezing protection activated on the air conditioning unit.
Restricted airflow across the indoor evaporator coil due to clogged air filters, a faulty indoor coil NTC temperature sensor, or low refrigerant pressure causing frost buildup on the heat exchanger.
Disconnect mains power, clean the indoor air filters and evaporator fins, and measure the indoor coil NTC sensor resistance with a multimeter (nominal: 5kΩ–10kΩ at 20°C). Verify indoor fan motor speed and refrigerant operating pressures.
Machine is not draining water
The drain filter is clogged, the drain pump is blocked or faulty, or the drain hose is kinked or blocked.
Clean the drain pump filter located at the bottom front of the machine. Check the drain hose for obstructions. Inspect the drain pump impeller.
Hob does not work, shows error code
The mains voltage supply to the hob is incorrect (too high or too low).
This is an electrical supply issue. Turn off the hob at the circuit breaker. An electrician should check the household wiring and the connection to the hob.
Machine overfills with water or anti-flood system activated
The pressure switch is faulty, or there's a blockage in the pressure switch hose.
Inspect the pressure switch and its connecting hose for blockages or damage. Replace the pressure switch if faulty.
Compressor exhaust high temperature protection
A cooking zone has overheated. This can happen during prolonged use at maximum power or if an unsuitable/empty pan is used.
Check for refrigerant leak, blockage, or faulty exhaust temp sensor. PRO TIP: For communication (E6) and sensor errors, always check the wiring connections between the indoor and outdoor units or sensor harness before replacing parts.
Airlux E05: NTC temperature sensor signal out of range (open or short circuit) in Washing Machine.
The NTC temperature sensor is faulty (open or short circuit).
Test the resistance of the NTC sensor with a multimeter. Check wiring to the sensor. Replace the sensor if it is out of specification.
AC over-current protection
Filters are blocked, drain hose is kinked or clogged, or the drain pump is faulty.
Check voltage supply and compressor for over-current conditions.
Communication failure between indoor unit and outdoor unit
There is a communication error between the induction coil and the main control board for a specific zone.
Check wiring/terminal blocks between indoor and outdoor units. PRO TIP: For communication (E6) and sensor errors, always check the wiring connections between the indoor and outdoor units or sensor harness before replacing parts.
Dishwasher not filling or washing correctly
The flow meter, which measures the amount of water entering, is faulty or blocked.
Inspect the flow meter (often part of the water softener assembly) for blockages or damage. Check its electrical connections. Replace if faulty.
Drum does not turn or spins erratically
The motor's tacho sensor, which measures speed, is faulty or has a poor connection.
Check the wiring and connections on the motor's tacho sensor. Inspect the sensor itself for damage. The motor may need replacement if the sensor is integrated.
Anti-high temperature protection
Component fatigue, sensor feedback out of tolerance, wiring harness connector discontinuity, or electronic control board glitch.
Check system for proper airflow and clean coils.
Fridge is not cooling, compressor may not be running
This error often indicates a fault with the temperature selector or thermostat, preventing the cooling cycle from starting.
Try adjusting the temperature setting. If there is no response, the thermostat or control board may need to be diagnosed and replaced.
Program stops, possible tripping of house electrics
The heating element has a short circuit or an insulation failure.
Disconnect the appliance from the mains. Test the heating element for continuity and earth leakage. Replace the heating element if faulty.
Machine is dead or unresponsive
The main control board (PCB) is faulty or has incorrect programming.
Check power supply to the machine. If power is present, the main PCB likely needs to be inspected and replaced by a qualified technician.
Loading EEPROM malfunction
Defective PCB Power Supply Rails & DC Bus Filter Capacitors, open/short circuit in the wiring harness, or faulty connector on the electronic control board (pcb) & bus communications.
Main PCB memory error. Board may need replacement.
Door lock failure during pyrolytic cleaning cycle
The door lock motor is faulty or the wiring to it is damaged.
Allow the oven to cool completely. Reset by turning off mains power. Inspect the door lock mechanism and its wiring. Replace the door lock assembly if necessary.
Oven shuts down completely during use
The safety thermostat has tripped due to an overheating condition, often caused by a failed cooling fan or blocked vents.
Check that the cooling fan is operational and that vents are not blocked. The safety thermostat may need to be manually reset or replaced if faulty.
Hob is beeping continuously, may not respond
A touch control key is being permanently pressed, either by a spillage, an object on the control panel, or a faulty sensor.
Clean and dry the control panel area thoroughly. Ensure no objects are resting on it. If the error persists, the touch control unit may need replacement.
IPM over temperature limit / drop frequency
Defective 3-Phase Motor Windings / Tacho Generator / Carbon Brushes, open/short circuit in the wiring harness, or faulty connector on the drive motor, inverter & tachometer sensor.
Inverter module too hot, dropping frequency.
The cooking zone does not heat up and the indicator flashes 'F'
No pan is detected on the induction zone, or the pan is unsuitable for induction cooking (e.g., glass, aluminum, copper).
Place a suitable, ferromagnetic pan (a magnet should stick to the base) on the cooking zone. Ensure the pan base is flat and covers the zone markings.
Indoor ambient sensor open or short circuit
The freezer compartment's temperature sensor (thermistor) has failed.
Inspect or replace indoor ambient temperature sensor.
Indoor tube sensor open or short circuit
The refrigerator compartment's temperature sensor (thermistor) has failed.
Inspect or replace indoor coil (tube) temperature sensor.
Outdoor ambient sensor open or short circuit
The defrost system's temperature sensor has failed, preventing the appliance from initiating or terminating the defrost cycle correctly.
Inspect or replace outdoor ambient temperature sensor.