Access our premium database of error codes, common faults, and professional repair solutions for Korting appliances.
Dishwasher stops, beeps, drain pump may run continuously
Water has leaked into the base pan, activating the anti-flood (AquaStop) switch.
Disconnect from power. Check for leaks from hoses, pump seals, or the dishwasher tub. Dry the base pan to reset the switch.
Freezer temperature is not regulated correctly
The freezer compartment's temperature sensor (NTC) is faulty or disconnected.
Check the wiring to the freezer sensor. Test the sensor's resistance; if out of specification, replace it.
Refrigerator compartment temperature is not regulated correctly
The fresh food (refrigerator) compartment's temperature sensor (NTC) is faulty or disconnected.
Locate and check the wiring to the refrigerator sensor. Test the sensor's resistance and replace if faulty.
Korting E10: Water inlet / filling timeout in Washing Machine; appliance fails to fill to minimum operational level.
Low water pressure, kinked inlet hose, or clogged water inlet valve filter.
Check that the water tap is fully open. Straighten the inlet hose. Clean the mesh filter on the water inlet valve.
Oven does not heat or shows incorrect temperature
The oven temperature sensor (probe/NTC) is faulty (open circuit) or its wiring is disconnected.
Perform a resistance test on the temperature sensor. If out of range or showing an open circuit, replace it. Check wiring.
Korting F2: NTC temperature sensor signal out of range (open or short circuit) in Oven / Microwave.
The temperature sensor is providing incorrect readings or a relay on the control board is stuck in the closed position.
Test the temperature sensor. If the sensor is good, the main control board likely needs to be replaced due to a faulty relay.
Oven is unresponsive, display may be blank or erratic
Internal communication error on the main control board (PCB).
Try resetting the oven by turning off the circuit breaker for 5 minutes. If the fault persists, the main control board requires replacement.
Oven will not heat and displays error
The oven temperature sensor (NTC) has a short circuit.
Test the resistance of the temperature sensor. A reading near zero ohms indicates a short circuit. Replace the sensor.
Dishes are not being cleaned properly
The main circulation pump is blocked or faulty, or the spray arms are clogged.
Remove and clean the spray arms, ensuring the holes are clear. Check the circulation pump for any obstructions like glass or food debris.
Machine fails to drain water
The drain pump filter is clogged, the drain hose is blocked or kinked, or the drain pump is faulty.
Unplug the machine. Clean the drain pump filter located at the front bottom. Check the drain hose for any blockages or kinks.
Door lock issue; self-clean won't start or door stuck locked
Fault with the motorized door lock assembly or the door position switch.
Check the door lock mechanism for physical obstruction or damage. Test the motor and switches for continuity.
Machine has stopped and may have water in the base
A leak has been detected in the base of the machine, activating the AquaStop float switch.
Unplug the appliance and shut off the water supply. Tilt the machine to drain the base pan. Locate and repair the source of the leak (e.g., hose, seal).
Korting F10: Water/air heating failure in Dishwasher; heating circuit does not reach set temperature.
Faulty heating element, wiring issue, or a problem with the control board's heating relay.
Test the heating element for continuity using a multimeter. Check all wiring and connections to the heater. The control board may be faulty.
Dishwasher is not filling with water
Water supply is turned off, inlet hose is kinked, or the filter on the inlet valve is blocked.
Ensure the water tap is fully on. Check the inlet hose for kinks. Unscrew the hose from the dishwasher and clean the small mesh filter.
High temperature alarm, display may flash
The internal temperature has been too high for an extended period. Common causes include the door being left open, a recent large grocery load, or a power outage.
Ensure the door is fully closed. Allow several hours for the temperature to stabilize. If the alarm persists, it could indicate a cooling system failure.
Our official certified partners service Korting appliances in your area.