Skip to content

CodesErreur.comSWISS PRO ENGINE

Core Diagnostics

Diagnostics Brands OEM Manuals Specialists AI EngineerPRO

Workshop Tools

Diagnostic ToolsNEW

Hardware interfaces & test probes

Find Rating Plate

Locate exact E-Nr, PNC & serial codes

Global OEM spare parts suppliers

Community & Career

Academy & Courses

Masterclasses by senior technicians

Certification ExamsPRO

Verify your B2B technical credentials

Peer-to-peer field troubleshooting

B2B recruitment & field opportunities

Global ranking of verified specialists

Certified Appliance Engineering EcosystemApply for Certification →

Language Selector

Account & Access

V-Zug • Central Diagnostic Dictionary

165 Verified Codes in Database

V-Zug Error Codes & Diagnostics

Access our premium database of error codes, common faults, and professional repair solutions for V-Zug appliances.

Luxury front-loading washing machine in brushed titanium with illuminated dark glass drum

CodeAppliancesFault / DiagnosticsRepair InstructionsAction

E08

Tumble Dryer

Refrigeration Compressor, Defrost Heater & PTC Relay

V-ZUG AdoraDry / AdoraTrocknen V2000-V6000 DualDry Heat Pump Dryer: Thermodynamic evaporator sensor anomaly E08; evaporator temperature curve fails to stabilize, signaling refrigeration circuit imbalance.

On V-ZUG heat pump dryers with AdoraDry DualDry closed-loop heat pump thermodynamic circuit, EcoManagement, and conductivity sensor strips: Low R134a/R290 refrigerant charge due to micro-leak, iced evaporator fins blocking airflow, or open NTC thermistor (~5–10 kΩ at 25°C).

Inspect evaporator fins for ice buildup; defrost if necessary. Measure evaporator NTC probe resistance (~5–10 kΩ at 25°C). If fins remain warm during run, inspect for refrigerant leak. Turn program dial to Stop. Hold the Gentle and Start keys together for 5 seconds until display shows '000', then power cycle the dryer.

E08

Hob / Cooktop

NTC Temperature Sensor & Thermistor

V-ZUG CookTop / FullFlex / DualFlex Swiss Induction Cooktop: Aluminum heatsink overtemperature cut-off E08; cooktop displays temperature warning and reduces or turns off zone power until cooled.

On V-ZUG cooktops with FullFlex multi-inductor surface matrix, OptiGlass ultra-hard diamond coating, and optical pan detection: Inadequate kitchen cabinet ventilation space (<5 mm front intake / rear exhaust), dried thermal grease between IGBTs and heatsink, or open heatsink NTC (~10 kΩ at 25°C).

Verify kitchen cabinet installation adheres to clearance specifications. Measure heatsink NTC probe resistance (~10 kΩ at 25°C). Renew thermal paste if heatsink was unseated. Wipe induction glass surface completely dry. Cut mains supply at breaker box for 60 seconds, restore and touch Key Lock for 5 seconds.

E08

Oven / Microwave

NTC Temperature Sensor & Thermistor

V-ZUG Combair / Combi-Steam / Miwell V6000 Swiss Luxury Oven: Hot air convection fan blower motor stalled E08; fan does not rotate during fan-assisted cooking modes, leading to uneven hot spots.

On V-ZUG ovens with Combair / Combi-Steam Electronic Steam System (ESS), climate sensor chamber, and PT1000 platinum probe (~1090 Ω at 25°C): Fat and grease buildup seizing bronze bearings, burned motor winding (~120–190 Ω), or failed phase-shift capacitor.

Check fan blade for free manual rotation. Measure motor winding resistance across terminals (~120–190 Ω). Test AC supply voltage from relay board when activated. Switch dial to 0 position. Disconnect master circuit breaker on fuse board for 60 seconds, restore power, and re-confirm clock time.

E08

Refrigerator / Freezer

Refrigeration Compressor, Defrost Heater & PTC Relay

V-ZUG SupremeLine / CombiCooler / Cooler V6000 Luxury Refrigerator: Inverter compressor drive controller trip E08; compressor buzzes or clicks repeatedly without running, halting all cooling.

On V-ZUG refrigeration units with SupremeLine dual refrigeration circuits, MonoFiX precision mounting, and multi-zone dynamic air management: Blown IPM power bridge on inverter PCB, seized mechanical piston, or unbalanced 3-phase compressor winding (~6–15 Ω U-V-W).

Unplug compressor plug. Measure phase-to-phase resistance across terminals: U-V, V-W, W-U must be identical (~6–15 Ω). Verify no continuity to ground (>10 MΩ). Open fresh food door, press and hold the Cold and Alarm Mute touch pads together for 6 seconds until confirmation chime sounds.

E08

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

V-ZUG AdoraWash / Unimatic V2000-V6000 Swiss Precision Washer: Motor drive overload E08; drum fails to rotate or hums briefly before inverter shutdown due to locked rotor overcurrent.

On V-ZUG washing machines utilizing AdoraWash vibration absorbing system (VAS), OptiTime energy logic, and brushless synchronous inverter drive: Foreign object wedged between drum and tub, seized tub bearings, or short-circuit in inverter power IGBT stage.

Spin drum by hand to confirm smooth free rotation. Disconnect motor connector and measure resistance between phases U-V, V-W, U-W (~5.5–12.5 Ω balanced). Turn appliance off with the Main button. Press and hold Start/Pause and Spin Speed simultaneously for 5 seconds until 'Fn' code clears.

E09

Dishwasher

General System & Mechanical Integration

V-ZUG AdoraDish / AdoraSpülen V2000-V6000 SteamFinish Dishwasher: AquaSensor turbidity calibration fault E09; optical sensor photodiode output remains saturated, disabling auto-wash soil detection.

On V-ZUG dishwashers featuring AdoraDish SteamFinish technology, FunctionLight optical projection, and active zeolite condensation adsorption: Opaque greasy film coating optical prism windows in sump, degraded infrared emitter LED, or loose 3-pin harness plug.

Extract turbidity sensor from sump base. Clean optical lenses thoroughly with alcohol wipe. Verify 5V DC supply and signal voltage (0.5V–4.5V DC). Open door slightly, press and hold the Program Selection sensor for 4 seconds until three acoustic beeps confirm memory reset, then latch door.

E09

Tumble Dryer

Door Lock Mechanism & Safety Interlock

V-ZUG AdoraDry / AdoraTrocknen V2000-V6000 DualDry Heat Pump Dryer: Door interlock microswitch contact open E09; dryer will not initiate cycle and display prompts user to close door.

On V-ZUG dryers with AdoraDry DualDry closed-loop heat pump thermodynamic circuit, EcoManagement, and conductivity sensor strips: Misaligned door strike pin, snapped mechanical latch hook, oxidized microswitch contacts, or disconnected wire harness.

Inspect door latch catch. Test switch continuity with door closed: resistance must be <0.5 Ω across contacts; open circuit when open. Realign door hinges if needed. Turn program dial to Stop. Hold the Gentle and Start keys together for 5 seconds until display shows '000', then power cycle the dryer.

E09

Hob / Cooktop

General System & Mechanical Integration

V-ZUG CookTop / FullFlex / DualFlex Swiss Induction Cooktop: Cookware material incompatible with induction field E09; cooking zone fails to generate eddy currents and display flashes pan alert.

On V-ZUG cooktops with FullFlex multi-inductor surface matrix, OptiGlass ultra-hard diamond coating, and optical pan detection: Utensil made of pure aluminum, copper, glass, or non-magnetic austenitic stainless steel; base diameter below 120 mm.

Test bottom of cookware with permanent magnet: magnet must attract strongly and uniformly across the flat base. Use cookware with thick ferrous multilayer base. Wipe induction glass surface completely dry. Cut mains supply at breaker box for 60 seconds, restore and touch Key Lock for 5 seconds.

E09

Oven / Microwave

NTC Temperature Sensor & Thermistor

V-ZUG Combair / Combi-Steam / Miwell V6000 Swiss Luxury Oven: Display to relay power board bus communication error E09; front panel controls lock up or display posts continuous error alert.

On V-ZUG ovens with Combair / Combi-Steam Electronic Steam System (ESS), climate sensor chamber, and PT1000 platinum probe (~1090 Ω at 25°C): Damaged communication ribbon harness, contact oxidation on JST PCB connectors, or blown 12V/5V DC line buffer IC on power board.

Unplug oven power. Inspect interconnecting harness between user interface and relay PCB. Verify continuity of all conductors (<0.3 Ω). Check 12V and 5V DC power rails. Switch dial to 0 position. Disconnect master circuit breaker on fuse board for 60 seconds, restore power, and re-confirm clock time.

E09

Refrigerator / Freezer

Refrigeration Compressor, Defrost Heater & PTC Relay

V-ZUG SupremeLine / CombiCooler / Cooler V6000 Luxury Refrigerator: Motorized cold air duct damper valve jammed E09; fresh food compartment either freezes excessively or warms up above +10°C.

On V-ZUG refrigeration units with SupremeLine dual refrigeration circuits, MonoFiX precision mounting, and multi-zone dynamic air management: Ice build-up preventing damper blade movement, stripped plastic stepper gears, or open damper motor coil (~3.5–5.0 kΩ).

Inspect air duct housing for ice blockage; defrost thoroughly. Measure stepper motor coil resistance (~3.5–5.0 kΩ across coil pairs). Replace motorized damper assembly. Open fresh food door, press and hold the Cold and Alarm Mute touch pads together for 6 seconds until confirmation chime sounds.

E09

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

V-ZUG AdoraWash / Unimatic V2000-V6000 Swiss Precision Washer: Program selector anomaly E09; appliance displays erratically jumping program cycles or ignores dial rotation commands.

On V-ZUG washing machines featuring AdoraWash vibration absorbing system (VAS), OptiTime energy logic, and brushless synchronous inverter drive: Oxidized rotary optical/mechanical encoder tracks, cracked potentiometer solder joints, or liquid ingress on display PCB.

Dismantle user interface panel. Inspect encoder soldering joints. Clean contact tracks with electrical contact cleaner or replace encoder module. Turn appliance off with the Main button. Press and hold Start/Pause and Spin Speed simultaneously for 5 seconds until 'Fn' code clears.

E9

Hob / Cooktop

Electronic Control Board (PCB) & Bus Communications

Internal electronic fault. Diagnostic error code E9 reported on V-Zug Hob.

On V-Zug Hob: A general error has occurred on the main power or control board.

On V-Zug Hob: Disconnect the hob from the mains power for 10 minutes to perform a reset. If the fault returns, the electronics need to be serviced.

E10

Dishwasher

Electronic Control Board (PCB) & Bus Communications

V-ZUG AdoraDish / AdoraSpülen V2000-V6000 SteamFinish Dishwasher: Appliance configuration error E10; microcontroller firmware detects model ID mismatch or corrupted cycle EEPROM parameters.

On V-ZUG dishwashers utilizing AdoraDish SteamFinish technology, FunctionLight optical projection, and active zeolite condensation adsorption: Unprogrammed replacement power module installed, electrical surge corruption, or defective flash memory bank.

Cycle mains power for 5 minutes. If code returns, configure appliance model variant code via diagnostic service menu or flash service tool. Open door slightly, press and hold the Program Selection sensor for 4 seconds until three acoustic beeps confirm memory reset, then latch door.

E10

Tumble Dryer

General System & Mechanical Integration

V-ZUG AdoraDry / AdoraTrocknen V2000-V6000 DualDry Heat Pump Dryer: Condenser heat exchanger blocked E10; internal casing temperature rises excessively and drying time doubles.

On V-ZUG dryers with AdoraDry DualDry closed-loop heat pump thermodynamic circuit, EcoManagement, and conductivity sensor strips: Dense mat of microfibers compacted deep between condenser cooling aluminum fins, choking heat dissipation.

Remove or open condenser maintenance hatch. Vacuum fins gently using a soft brush attachment. Straighten bent cooling fins with a fin comb. Turn program dial to Stop. Hold the Gentle and Start keys together for 5 seconds until display shows '000', then power cycle the dryer.

E10

Hob / Cooktop

Drive Motor, Inverter & Tachometer Sensor

V-ZUG CookTop / FullFlex / DualFlex Swiss Induction Cooktop: High-frequency resonance circuit capacitor degradation E10; induction zones hum loudly or fault under medium power settings.

On V-ZUG cooktops with FullFlex multi-inductor surface matrix, OptiGlass ultra-hard diamond coating, and optical pan detection: Capacitance loss or dielectric breakdown in high-voltage polypropylene snubber film capacitors (typically 0.47 µF–0.68 µF / 1000V DC).

Desolder resonant film capacitors from inverter board. Test value with LCR capacitance meter: replace any component deviating by >5% from nominal rating. Wipe induction glass surface completely dry. Cut mains supply at breaker box for 60 seconds, restore and touch Key Lock for 5 seconds.

E10

Oven / Microwave

NTC Temperature Sensor & Thermistor

V-ZUG Combair / Combi-Steam / Miwell V6000 Swiss Luxury Oven: Door contact position switch defect E10; oven fails to detect closed door, cavity lights remain on or baking cycle stops.

On V-ZUG ovens with Combair / Combi-Steam Electronic Steam System (ESS), climate sensor chamber, and PT1000 platinum probe (~1090 Ω at 25°C): Misaligned push pin on door frame, broken actuator spring in microswitch, or scorched switch contacts (<0.5 Ω closed).

Inspect door switch push rod at top/side of cavity. Measure switch contact resistance: must read <0.5 Ω when pressed in, open when released. Replace switch if faulty. Switch dial to 0 position. Disconnect master circuit breaker on fuse board for 60 seconds, restore power, and re-confirm clock time.

E10

Refrigerator / Freezer

General System & Mechanical Integration

V-ZUG SupremeLine / CombiCooler / Cooler V6000 Luxury Refrigerator: Door ajar position switch failure E10; alarm beeps continuously with door firmly shut and interior lights fail to turn off.

On V-ZUG refrigeration units with SupremeLine dual refrigeration circuits, MonoFiX precision mounting, and multi-zone dynamic air management: Dislodged door gasket magnet, broken reed switch in top header panel, or severed door hinge wiring harness.

Pass a small neodymium magnet across reed switch location to test contact closure (<0.5 Ω). Inspect door hinge harness for fractured wires. Replace reed board if open. Open fresh food door, press and hold the Cold and Alarm Mute touch pads together for 6 seconds until confirmation chime sounds.

E10

Washing Machine

Water Level Pressure Switch & Air Dome

V-ZUG AdoraWash / Unimatic V2000-V6000 Swiss Precision Washer: Water level sensing error E10; analog pressure sensor output frequency outside calibrated operational bounds (21–27 kHz).

On V-ZUG washing machines utilizing AdoraWash vibration absorbing system (VAS), OptiTime energy logic, and brushless synchronous inverter drive: Soap scum clogging pressure bell chamber, pinholed pressure transducer hose, or internal LC oscillator fault.

Disconnect and flush pressure bell with warm water. Inspect silicone hose for punctures. Measure sensor supply voltage (5V DC) and signal pin. Turn appliance off with the Main button. Press and hold Start/Pause and Spin Speed simultaneously for 5 seconds until 'Fn' code clears.

E11

Dishwasher

General System & Mechanical Integration

V-ZUG AdoraDish / AdoraSpülen V2000-V6000 SteamFinish Dishwasher: Communication bus loss E11; door user interface touch panel loses serial synchronous link with main base power controller.

On V-ZUG dishwashers featuring AdoraDish SteamFinish technology, FunctionLight optical projection, and active zeolite condensation adsorption: Wire harness sheared or pinched in the lower door hinge articulation, corroded pins, or faulty transceiver.

Inspect wiring harness where it bends through lower door hinge protector. Check continuity of serial data lines. Ensure 12V and 5V DC rails are stable. Open door slightly, press and hold the Program Selection sensor for 4 seconds until three acoustic beeps confirm memory reset, then latch door.

E11

Tumble Dryer

Drive Motor, Inverter & Tachometer Sensor

V-ZUG AdoraDry / AdoraTrocknen V2000-V6000 DualDry Heat Pump Dryer: Drum drive belt broken or snapped E11; drive motor runs but drum does not rotate; safety switch halts operation.

On V-ZUG dryers with AdoraDry DualDry closed-loop heat pump thermodynamic circuit, EcoManagement, and conductivity sensor strips: Snapped poly-V drive belt, broken belt tensioner idler pulley arm, or tension switch triggered by lack of belt tension.

Remove top lid and rear cover. Inspect drum drive belt and spring-loaded tensioner pulley. Install new manufacturer-spec Poly-V belt and verify switch closure (<0.5 Ω). Turn program dial to Stop. Hold the Gentle and Start keys together for 5 seconds until display shows '000', then power cycle the dryer.

E11

Hob / Cooktop

General System & Mechanical Integration

V-ZUG CookTop / FullFlex / DualFlex Swiss Induction Cooktop: Liquid spillover or foreign object on touch panel E11; safety lockout turns off all zones and beeps continuously.

On V-ZUG cooktops with FullFlex multi-inductor surface matrix, OptiGlass ultra-hard diamond coating, and optical pan detection: Boiling water, sauce, damp cloth, or metallic lid covering capacitive touch sensor pads for longer than 10 seconds.

Remove all utensils from touch area. Wipe glass dry with clean cotton towel. Allow capacitive sensors 15 seconds to recalibrate background baseline. Wipe induction glass surface completely dry. Cut mains supply at breaker box for 60 seconds, restore and touch Key Lock for 5 seconds.

E11

Oven / Microwave

NTC Temperature Sensor & Thermistor

V-ZUG Combair / Combi-Steam / Miwell V6000 Swiss Luxury Oven: Food meat core probe sensor short or fault E11; oven triggers alert when probe is plugged into socket or shows erratic internal temperature.

On V-ZUG ovens with Combair / Combi-Steam Electronic Steam System (ESS), climate sensor chamber, and PT1000 platinum probe (~1090 Ω at 25°C): Water or grease ingress into probe internal element, shorted 3.5 mm jack socket connector, or pinched high-temperature cable.

Measure resistance across probe jack tip and sleeve: expected ~10 kΩ (NTC) or ~1000 Ω (PT1000) at 25°C. Clean cavity jack socket with electrical contact spray. Switch dial to 0 position. Disconnect master circuit breaker on fuse board for 60 seconds, restore power, and re-confirm clock time.

E11

Refrigerator / Freezer

Refrigeration Compressor, Defrost Heater & PTC Relay

V-ZUG SupremeLine / CombiCooler / Cooler V6000 Luxury Refrigerator: Automatic ice maker motor twist or harvest failure E11; ice maker stops producing ice cubes and harvest fingers stall mid-rotation.

On V-ZUG refrigeration units with SupremeLine dual refrigeration circuits, MonoFiX precision mounting, and multi-zone dynamic air management: Ice cubes frozen together jamming harvest rake, stripped reduction gear in drive motor (~3.0–4.5 kΩ), or microswitch failure.

Defrost ice mold using warm water. Press ice maker manual test cycle button. Measure motor coil resistance (~3.0–4.5 kΩ). Replace ice maker module if motor fails test. Open fresh food door, press and hold the Cold and Alarm Mute touch pads together for 6 seconds until confirmation chime sounds.

E11

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

V-ZUG AdoraWash / Unimatic V2000-V6000 Swiss Precision Washer: Detergent dispensing fault E11; motorized distributor flap fails to rotate to the requested compartment position.

On V-ZUG washing machines featuring AdoraWash vibration absorbing system (VAS), OptiTime energy logic, and brushless synchronous inverter drive: Jammed mechanical water diverter gears, calcified linkage arms, or defective synchronous actuator motor (~3.5–5.5 kΩ).

Remove top lid and inspect dispenser gear mechanism. Clean limescale deposits. Measure resistance of dispenser actuator motor (~3.5–5.5 kΩ). Turn appliance off with the Main button. Press and hold Start/Pause and Spin Speed simultaneously for 5 seconds until 'Fn' code clears.

E12

Dishwasher

Water Level Pressure Switch & Air Dome

V-ZUG AdoraDish / AdoraSpülen V2000-V6000 SteamFinish Dishwasher: Water level sensor mismatch E12; analog pressure transducer reading conflicts with circulation pump motor load telemetry.

On V-ZUG dishwashers utilizing AdoraDish SteamFinish technology, FunctionLight optical projection, and active zeolite condensation adsorption: Grease accumulation in sump air trap chamber, split pressure sensor tube, or drifting diaphragm sensor.

Flush air trap dome in sump using hot water syringe. Check pressure hose for splits. Measure pressure sensor output voltage (0.5V–4.0V DC). Open door slightly, press and hold the Program Selection sensor for 4 seconds until three acoustic beeps confirm memory reset, then latch door.

E12

Tumble Dryer

General System & Mechanical Integration

V-ZUG AdoraDry / AdoraTrocknen V2000-V6000 DualDry Heat Pump Dryer: Mains supply voltage out of tolerance E12; appliance pauses cycle, display flickers, or resets spontaneously.

On V-ZUG dryers with AdoraDry DualDry closed-loop heat pump thermodynamic circuit, EcoManagement, and conductivity sensor strips: AC supply voltage dropped below 185V AC or surged above 265V AC, loose terminal block screws, or high wall socket contact resistance.

Measure AC voltage at wall socket under load (must be 230V ±10%, 50Hz). Inspect terminal block connections for scorched pins or loose clamping screws. Turn program dial to Stop. Hold the Gentle and Start keys together for 5 seconds until display shows '000', then power cycle the dryer.

E12

Hob / Cooktop

Electronic Control Board (PCB) & Bus Communications

V-ZUG CookTop / FullFlex / DualFlex Swiss Induction Cooktop: Induction power module EEPROM parameter mismatch E12; power board fails configuration handshake and remains locked.

On V-ZUG cooktops with FullFlex multi-inductor surface matrix, OptiGlass ultra-hard diamond coating, and optical pan detection: Incompatible software revisions between touch user interface and power generator, or corrupted calibration data table.

Perform complete mains power cycle (switch off breaker for 5 minutes). If error persists, configure model code via service test routine or replace matched board pair. Wipe induction glass surface completely dry. Cut mains supply at breaker box for 60 seconds, restore and touch Key Lock for 5 seconds.

E12

Oven / Microwave

NTC Temperature Sensor & Thermistor

V-ZUG Combair / Combi-Steam / Miwell V6000 Swiss Luxury Oven: AC line voltage undervoltage trip E12; oven drops out of preheat mode or display dims and restarts repeatedly.

On V-ZUG ovens with Combair / Combi-Steam Electronic Steam System (ESS), climate sensor chamber, and PT1000 platinum probe (~1090 Ω at 25°C): AC line voltage dipping below 190V AC under heating element load, loose terminal jumper bridges, or weak neutral wire connection.

Measure line voltage across L and N terminals with elements powered on (must remain >207V AC). Tighten all screw clamps on the rear connection terminal block. Switch dial to 0 position. Disconnect master circuit breaker on fuse board for 60 seconds, restore power, and re-confirm clock time.

E12

Refrigerator / Freezer

Water Inlet Valve, Aquastop & Flowmeter

V-ZUG SupremeLine / CombiCooler / Cooler V6000 Luxury Refrigerator: Water dispenser or ice maker inlet solenoid valve failure E12; dispenser will not dispense water or water dribbles into door tray.

On V-ZUG refrigeration units with SupremeLine dual refrigeration circuits, MonoFiX precision mounting, and multi-zone dynamic air management: Open solenoid valve coil (~1.8–2.8 kΩ), mineral scale seizing internal plunger valve, or clogged sediment pre-filter screen.

Disconnect dual solenoid valve leads at rear base. Measure coil resistance of both water and ice solenoids (~1.8–2.8 kΩ). Clean inlet screen filter under tap. Open fresh food door, press and hold the Cold and Alarm Mute touch pads together for 6 seconds until confirmation chime sounds.

E12

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

V-ZUG AdoraWash / Unimatic V2000-V6000 Swiss Precision Washer: Serial communication timeout E12; user interface display panel loses bidirectional handshake link with main power board.

On V-ZUG washing machines utilizing AdoraWash vibration absorbing system (VAS), OptiTime energy logic, and brushless synchronous inverter drive: Corroded wire harness crimp connectors, electrical noise coupling on serial line, or defective bus transceiver IC.

Inspect wiring harness connecting display module and power PCB. Reseat connectors firmly. Verify 5V DC and 12V DC power rails from main board. Turn appliance off with the Main button. Press and hold Start/Pause and Spin Speed simultaneously for 5 seconds until 'Fn' code clears.

← Previous PagePage 3 of 6 (165 results)Next Page →

V-Zug — Complete Error Code Catalog

65 Verified Error Codes

Server-side index of all verified manufacturer error codes for technicians and automated crawlers.

Dishwasher29

C1 E01 E02 E03 E04 E05 E06 E07 E08 E09 E10 E11 E12 E13 E14 E15 F01 F02 F03 F04 F05 F13 F22 i10 i20 i30 i50 i60 iC0

Washing Machine17

A01 A02 A03 A05 A06 A07 A09 A10 A13 A15 A16 E18 E19 E20 F06 F08 F14

Tumble Dryer1

Oven / Microwave8

E17 E30 Er1 Er3 Er6 F3 F4 F6

Hob / Cooktop5

Refrigerator / Freezer5

AL01 AL02 E1 E2 E3

Need Help? Call a Certified Technician

Our official certified partners service V-Zug appliances in your area.

Electroassistance (Switzerland)Appliance Care UK (United Kingdom)

CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search Database PRO Diagnostic AIPRO Diagnostic Tools Brands

Workshop Tools

Brands (87)OEM Manuals Find Rating Plate Parts Locator

For Technicians

Specialists Technician Forum Tech Jobs Premium

Corporate

Terms of Service Privacy PolicyOfficial Swiss Repair Partner: Electroassistance

OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Official Swiss Repair Partner: Electroassistance Terms of Service Privacy Policy