OEM VERIFIED BENCH

OFFICIAL FAULT CODEAL01

Sekom // OFFICIAL DIAGNOSTIC BENCH

Sekom AL01

Q: What does error code AL01 mean on a Sekom appliance?

Sekom error code AL01 indicates: Sekom AL01: Operational cycle fault detected during Dishwasher program execution..

Q: What is the root cause of Sekom error code AL01?

The primary root cause for Sekom code AL01 is: Alternative code for a leak detected in the base pan of the appliance..

Q: How do I fix or resolve Sekom error code AL01?

To resolve error code AL01: Disconnect power and water. Find and repair the source of the leak (hose, seal, pump). Dry the base pan and reset the float switch.

Q: Is it safe to clear Sekom error code AL01 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Sekom code AL01 persists, the physical component causing Alternative code for a leak detected in the base pan of the appliance. must be inspected or replaced.

Q: How do I test electrical resistance for Sekom code AL01 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Protective Earth Bonding & Incoming Mains Voltage across Between unpainted chassis metal and mains plug earth pin; incoming terminal block L-N. Expected nominal reading is Earth Ground Continuity: <0.1Ω (Chassis metal to mains plug earth pin). Mains: 230V AC ±10%.. Tolerance: Protective conductor impedance must remain <0.1Ω. Line voltage 207V–253V AC under load..

Q: What safety protocol must be followed before servicing Sekom code AL01?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

DishwasherGeneral System & Mechanical Integration

Dishwasher

Other Brands Sharing Code AL01:MieleAL01 WhirlpoolAL01 IndesitAL01 HaierAL01 CandyAL01 BauknechtAL01 V-ZugAL01 AristonAL01 HooverAL01 BrandtAL01

Symptom / Description

FAULT

Sekom AL01: Operational cycle fault detected during Dishwasher program execution.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Alternative code for a leak detected in the base pan of the appliance.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Disconnect power and water. Find and repair the source of the leak (hose, seal, pump). Dry the base pan and reset the float switch.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Sekom Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLGeneral System & Mechanical IntegrationDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

Earth Ground Continuity: <0.1Ω (Chassis metal to mains plug earth pin). Mains: 230V AC ±10%.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Protective Earth Bonding & Incoming Mains Voltage

Test Pins & Connections

PROBE (+)

PROBE (-)

Between unpainted chassis metal and mains plug earth pin; incoming terminal block L-N

Tolerance & Diagnostic CriteriaProtective conductor impedance must remain <0.1Ω. Line voltage 207V–253V AC under load.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect electrical mains plug or trip dedicated circuit breaker before servicing.
!Wait at least 5 minutes before opening any casing panels to reset volatile microcontrollers and bleed residual charges.
!Operate in a dry workshop environment; never bypass internal electrical thermal cutouts.

3. Preliminary Mechanical & Visual Checks

Check appliance leveling with a spirit level; adjust threaded leveling feet for perfect stability.
Check door and lid perimeter rubber gaskets for tears, gaps, or foreign object obstruction.
Inspect shock absorbers, suspension springs, and rubber dampers for mechanical fatigue or excessive play.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Sekom AL01

FAQ TREE

What does error code AL01 mean on a Sekom appliance?

Sekom error code AL01 indicates: Sekom AL01: Operational cycle fault detected during Dishwasher program execution..

What is the root cause of Sekom error code AL01?

The primary root cause for Sekom code AL01 is: Alternative code for a leak detected in the base pan of the appliance..

How do I fix or resolve Sekom error code AL01?

To resolve error code AL01: Disconnect power and water. Find and repair the source of the leak (hose, seal, pump). Dry the base pan and reset the float switch.

Is it safe to clear Sekom error code AL01 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Sekom code AL01 persists, the physical component causing Alternative code for a leak detected in the base pan of the appliance. must be inspected or replaced.

How do I test electrical resistance for Sekom code AL01 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Protective Earth Bonding & Incoming Mains Voltage across Between unpainted chassis metal and mains plug earth pin; incoming terminal block L-N. Expected nominal reading is Earth Ground Continuity: <0.1Ω (Chassis metal to mains plug earth pin). Mains: 230V AC ±10%.. Tolerance: Protective conductor impedance must remain <0.1Ω. Line voltage 207V–253V AC under load..

What safety protocol must be followed before servicing Sekom code AL01?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEAL01

Sekom // OFFICIAL DIAGNOSTIC BENCH

Sekom AL01

DishwasherGeneral System & Mechanical Integration

Dishwasher

Other Brands Sharing Code AL01:MieleAL01 WhirlpoolAL01 IndesitAL01 HaierAL01 CandyAL01 BauknechtAL01 V-ZugAL01 AristonAL01 HooverAL01 BrandtAL01

Symptom / Description

FAULT

Sekom AL01: Operational cycle fault detected during Dishwasher program execution.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

Alternative code for a leak detected in the base pan of the appliance.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Disconnect power and water. Find and repair the source of the leak (hose, seal, pump). Dry the base pan and reset the float switch.

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Sekom Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLGeneral System & Mechanical IntegrationDishwasher

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

Earth Ground Continuity: <0.1Ω (Chassis metal to mains plug earth pin). Mains: 230V AC ±10%.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Protective Earth Bonding & Incoming Mains Voltage

Test Pins & Connections

PROBE (+)

PROBE (-)

Between unpainted chassis metal and mains plug earth pin; incoming terminal block L-N

Tolerance & Diagnostic CriteriaProtective conductor impedance must remain <0.1Ω. Line voltage 207V–253V AC under load.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect electrical mains plug or trip dedicated circuit breaker before servicing.
!Wait at least 5 minutes before opening any casing panels to reset volatile microcontrollers and bleed residual charges.
!Operate in a dry workshop environment; never bypass internal electrical thermal cutouts.

3. Preliminary Mechanical & Visual Checks

Check appliance leveling with a spirit level; adjust threaded leveling feet for perfect stability.
Check door and lid perimeter rubber gaskets for tears, gaps, or foreign object obstruction.
Inspect shock absorbers, suspension springs, and rubber dampers for mechanical fatigue or excessive play.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Sekom AL01

FAQ TREE

What does error code AL01 mean on a Sekom appliance?

Sekom error code AL01 indicates: Sekom AL01: Operational cycle fault detected during Dishwasher program execution..

What is the root cause of Sekom error code AL01?

The primary root cause for Sekom code AL01 is: Alternative code for a leak detected in the base pan of the appliance..

How do I fix or resolve Sekom error code AL01?

To resolve error code AL01: Disconnect power and water. Find and repair the source of the leak (hose, seal, pump). Dry the base pan and reset the float switch.

Is it safe to clear Sekom error code AL01 by resetting power?

How do I test electrical resistance for Sekom code AL01 using a multimeter?

What safety protocol must be followed before servicing Sekom code AL01?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Sekom AL01

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Sekom AL01

Community Verification

Related Sekom Dishwasher Error Codes

Sekom AL01

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Sekom AL01

Community Verification

Related Sekom Dishwasher Error Codes