Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Water fill timeout E01; sump does not achieve required operating water volume within 4 minutes of program start.
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: Lint filter air flow restriction E01; drying cycle halts or extends drastically due to choked process air circulation.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Touch interface to induction power board link failure E01; display zones flash error and power level sliders are disabled.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Fresh food compartment NTC temperature sensor fault E01; cabinet temperature fluctuates erratically or food freezes on shelves.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Door interlock error E01; appliance refuses to commence wash cycle because door lock contact is not confirmed closed.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Induction coil pan detection failure E02; selected zone refuses to energize cookware, displays missing pot symbol, and turns off.
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Pyrolytic door lock mechanism failure E02; door fails to lock during self-clean cycle or remains jammed shut after cooling.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Freezer compartment temperature sensor defect E02; freezer warm alert triggers and compressor runs continuously without stopping.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Water intake timeout E02; drum water level does not reach target threshold within 5 minutes of fill valve activation.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Water heating failure E03; wash bath fails to attain wash setpoint temperature within 20 minutes of heater activation.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Power module IGBT inverter transistor short circuit E03; appliance trips home breaker instantly when zone power is dialed up.
Immersion / Air Heating Element & Klixon Thermostat
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Tangential cooling fan motor failure E03; electronic safety cuts off heating to prevent control panel and casing overheating.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Defrost termination evaporator sensor fault E03; evaporator coil freezes solid with ice, choking air circulation vents.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Drainage timeout error E03; waste wash water remains in tub after 4 minutes of drain pump activation.
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: Process air NTC temperature sensor fault E04; machine aborts cycle after 2 minutes or overheats and triggers safety trip.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Induction coil center temperature probe fault E04; zone display posts error and cuts heating to protect ceramic glass from cracking.
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Ambient room temperature sensor failure E04; dynamic defrost interval calculations and door heater logic misbehave.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Anti-flood protection triggered E04; safety drain pump runs continuously and program halts due to water in base pan.
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Temperature sensor communication anomaly E05; wash NTC circuit voltage drops to 0V (short) or rises to 5V (open circuit).
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Mains supply voltage high overvoltage protection E05; cooktop beeps and isolates electronic components to prevent catastrophic failure.
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Bottom sole heating element open circuit E05; bottom crust remains uncooked and lower chamber fails to reach set temperature.
Immersion / Air Heating Element & Klixon Thermostat
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Evaporator defrost heating element open circuit E05; defrost cycle aborts on maximum timer and ice completely encases cooling coil.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Heating malfunction E05; wash water temperature fails to increase by more than 4°C within 15 minutes of heater activation.
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Circulation pump motor stall E06; BLDC wash motor fails to maintain operating spray pressure or draws locked rotor current.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Mains supply undervoltage condition E06; cooktop drops booster power or shuts off all heating zones under heavy cooking load.
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Circular convection ring element open circuit E06; hot air convection mode blows cool air without heating chamber.
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Defrost circuit thermal safety fuse opened E06; defrost heater receives no voltage and freezer evaporator rapidly chokes with frost.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Unbalanced load warning E06; spin cycle aborted after multiple distribution attempts due to excessive drum eccentricity.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: Drum rotation drive motor failure E07; motor hums without rotating or stops reversing direction mid-program.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Induction module cooling fan motor stalled or missing tach E07; cooktop shuts down power to prevent heatsink thermal avalanche.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Top grill or broil element open circuit E07; upper heating zone does not glow red and browning or grilling fails completely.
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Freezer evaporator circulation fan motor stalled E07; air circulation stops, fresh food compartment warms up, and ice accumulates.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Motor drive velocity anomaly E07; control module detects sudden motor acceleration or missing tachometer frequency feedback.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Water softener circuit fault E08; salt chamber regeneration solenoid valve fails to open during regeneration cycle.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Aluminum heatsink overtemperature cut-off E08; cooktop displays temperature warning and reduces or turns off zone power until cooled.
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Hot air convection fan blower motor stalled E08; fan does not rotate during fan-assisted cooking modes, leading to uneven hot spots.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Inverter compressor drive controller trip E08; compressor buzzes or clicks repeatedly without running, halting all cooling.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Motor drive overload E08; drum fails to rotate or hums briefly before inverter shutdown due to locked rotor overcurrent.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: Door interlock microswitch contact open E09; dryer will not initiate cycle and display prompts user to close door.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Cookware material incompatible with induction field E09; cooking zone fails to generate eddy currents and display flashes pan alert.
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Display to relay power board bus communication error E09; front panel controls lock up or display posts continuous error alert.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Motorized cold air duct damper valve jammed E09; fresh food compartment either freezes excessively or warms up above +10°C.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Program selector anomaly E09; appliance displays erratically jumping program cycles or ignores dial rotation commands.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: High-frequency resonance circuit capacitor degradation E10; induction zones hum loudly or fault under medium power settings.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Door ajar position switch failure E10; alarm beeps continuously with door firmly shut and interior lights fail to turn off.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Communication bus loss E11; door user interface touch panel loses serial synchronous link with main base power controller.
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: Drum drive belt broken or snapped E11; drive motor runs but drum does not rotate; safety switch halts operation.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Liquid spillover or foreign object on touch panel E11; safety lockout turns off all zones and beeps continuously.
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Food meat core probe sensor short or fault E11; oven triggers alert when probe is plugged into socket or shows erratic internal temperature.
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Automatic ice maker motor twist or harvest failure E11; ice maker stops producing ice cubes and harvest fingers stall mid-rotation.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Detergent dispensing fault E11; motorized distributor flap fails to rotate to the requested compartment position.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Water level sensor mismatch E12; analog pressure transducer reading conflicts with circulation pump motor load telemetry.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: Mains supply voltage out of tolerance E12; appliance pauses cycle, display flickers, or resets spontaneously.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Induction power module EEPROM parameter mismatch E12; power board fails configuration handshake and remains locked.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: AC line voltage undervoltage trip E12; oven drops out of preheat mode or display dims and restarts repeatedly.
Immersion / Air Heating Element & Klixon Thermostat
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Water dispenser or ice maker inlet solenoid valve failure E12; dispenser will not dispense water or water dribbles into door tray.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Serial communication timeout E12; user interface display panel loses bidirectional handshake link with main power board.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Detergent dispenser actuator error E13; tablet compartment lid fails to release or rinse aid valve does not actuate.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Bridge flex zone synchronization failure E13; paired induction zones fail to link into unified rectangular cooking surface.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Lower machinery compartment condenser fan motor stalled E13; compressor overheats, high pressure rises, and cooling drops drastically.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Active drying system fault E14; zeolite regeneration heater or drying ventilation blower fan fails to engage during dry cycle.
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: Process cooling air blower fan stalled E14; secondary blower fan fails to run, causing internal thermal build-up and emergency shutdown.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Mains zero-crossing sync circuit failure E14; cooktop cannot time IGBT switching to AC waveform, shutting down all power.
Immersion / Air Heating Element & Klixon Thermostat
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Steam water feed pump or inlet valve failure E14; steam drawer does not dispense water into steam generator chamber.
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Refrigeration thermodynamic cycle inefficiency E14; compressor operates continuously for >120 minutes with zero cooling temperature drop.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Earth leakage safety trip E14; current leakage from heating element sheath to ground exceeds residual safety threshold.
Immersion / Air Heating Element & Klixon Thermostat
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: External condensate drain backflow or siphon restriction E15; condensate water overflows into base pan or triggers continuous pumping.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Power management current limiting relay fault E15; cooktop limits cooking power to single zone or refuses to heat at settings above level 4.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Multi-temperature convertible pantry drawer sensor fault E15; meat/fish or deli drawer temperature setting cannot be regulated.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Residual heat indicator 'H' stuck illuminated E16; display shows hot glass warning permanently even after cooktop is cold for hours.
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Motorized rotisserie spit drive stall E16; spit does not rotate when inserted into drive coupling during rotisserie program.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Door display to main power board serial communication failure E16; exterior touch interface goes black or flashes communication error.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Inverter module AC supply undervoltage lockout E17; compressor controller disables motor drive to protect power silicon.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Drum positioning error E17; automatic drum parking sensor fails to align opening flaps with the top access lid.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Hot water intake fault E19; secondary hot water inlet valve fails to supply water within allocated filling phase.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Gate driver circuit failure on induction power bridge F01; cooktop disables half of all cooking zones and displays service code.
Immersion / Air Heating Element & Klixon Thermostat
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Linear inverter compressor piston stroke feedback anomaly F01; compressor clatters loudly or shuts down due to stroke limit breach.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Motor phase imbalance fault F01; 3-phase BLDC motor inverter detects missing phase or unequal current consumption across UVW.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Water inlet triac short fault F02; water inlet solenoid valve is powered continuously even when machine is powered down.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Undersink installation cavity ambient overtemperature F02; cooktop pauses cooking and runs cooling fan at maximum speed.
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Defrost water drain gutter iced up or heater fault F02; meltwater overflows into bottom freezer drawers and freezes into a solid sheet.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Inverter module thermal alarm F02; motor drive controller halts operation due to excessive heatsink temperature (>88°C).
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Foam aeration cavitation fault F03; circulation wash pump motor loses prime and cavitates due to dense foam blanket in sump.
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: Display to power board serial communication failure F03; front touch interface unresponsive or flashes communication error.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Model configuration option bytes unconfigured F03; appliance displays error upon boot and disables compressor operation.
Compressor Motor Windings (Run/Start) & Defrost Heater
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Door latch status conflict F04; door interlock sensor reading contradicts mechanical door closure latch microswitch.
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: High-limit thermal safety cut-out opened F04; heater or compressor instantly de-energized to avert fire risk.
Immersion / Air Heating Element & Klixon Thermostat
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Inter-module dynamic power sharing bus timeout F04; cooktop limits aggregate power draw and disallows multi-zone high-heat cooking.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Safety overflow tripped F04; water level exceeds maximum safety mark and emergency drain pump is forcibly triggered.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Inverter DC bus rail voltage anomaly F05; excessive AC ripple voltage or unstable DC rail (>340V or <220V DC) detected on drive PCB.
Immersion / Air Heating Element & Klixon Thermostat
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: Process cooling air blower fan stalled E14; secondary blower fan fails to run, causing internal thermal build-up and emergency shutdown.
On Samsung dryers with OptimalDry triple sensor system (temperature, humidity, condenser mesh), and digital inverter heat pump: Foreign object or dense lint jamming fan impeller blades, seized blower motor sleeve bearing, or blown triac on PCB (~120–220 Ω motor coil).
Spin blower wheel by hand to ensure free rotation without binding. Check motor coil resistance (~120–220 Ω). Verify supply voltage is delivered by board when activated. Power on, touch and hold Dry Level and Time Dry pads simultaneously for 7 seconds until the display chime triggers, then power off.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Mains zero-crossing sync circuit failure E14; cooktop cannot time IGBT switching to AC waveform, shutting down all power.
On Samsung cooktops with Virtual Flame LED cooking glow simulation, Flex Zone wide inductors, and detachable magnetic control dial: High-value SMD resistor chain open on mains sensing line (typically 330 kΩ–1 MΩ), defective zero-cross comparator IC, or heavy harmonic line noise.
Inspect high-voltage sensing resistors on power board inlet stage. Verify 100 Hz (or 120 Hz) clock pulses at microcontroller zero-cross input pin with oscilloscope. Remove all cookware and liquids from glass. Power down circuit breaker for 60 seconds, restore power and press Control Lock for 4 seconds.
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Steam water feed pump or inlet valve failure E14; steam drawer does not dispense water into steam generator chamber.
On Samsung ovens with Dual Cook Flex articulated divider door, dual hot-air convection fans, and SmartThings culinary telemetry: Open pump solenoid coil (~2.2–3.6 kΩ), calcified diaphragm check valve preventing suction, or pinched silicone water tube.
Disconnect electrical terminals of water pump. Measure coil resistance (~2.2–3.6 kΩ). Check silicone suction tubes for kinks and unclog drawer docking seal. Turn off selector dial, unplug oven power cord or switch off main fuse for 5 minutes, reconnect power and configure initial clock time.
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Refrigeration thermodynamic cycle inefficiency E14; compressor operates continuously for >120 minutes with zero cooling temperature drop.
On Samsung refrigeration units with Twin Cooling Plus independent dual evaporators, Metal Cooling retention plate, and Digital Inverter compressor: Slow R600a/R134a refrigerant leak in internal aluminium evaporator tubing or partially blocked capillary expansion tube.
Touch compressor discharge pipe: if cold while running, refrigerant charge has escaped. Check suction pipe for frost ball. Certified refrigeration tech required for brazing/recharge. Press and hold Power Freeze and Power Cool buttons simultaneously for 8 seconds until the display flashes and clears stored fault codes.
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Earth leakage safety trip E14; current leakage from heating element sheath to ground exceeds residual safety threshold.
On Samsung washing machines utilizing EcoBubble foam generator, Digital Inverter BLDC drive motor, and VRT Plus active vibration reduction: Microscopic fissure in tubular stainless steel heater sheath allowing water ingress into magnesium oxide insulation.
Disconnect heater power leads. Use 500V megaohmmeter to test insulation resistance between heater terminal and metal flange (>2 MΩ required; replace if <2 MΩ). Power on, press and hold Spin Speed and Temperature keys together for 7 seconds until display clears or sounds a melody, then restart cycle.
Samsung WaterWall / StormWash / Bespoke Linear Wash Dishwasher: Power module DC voltage failure E15; internal switched-mode power supply rail drops below operational threshold (<10.5V DC).
On Samsung dishwashers featuring WaterWall sweeping linear spray bar, StormWash rotating nozzle cluster, and auto-release door opening: Degraded filter capacitor on main power board, shorted actuator coil pulling down rail, or defective SMPS IC.
Inspect power board for capacitor bulging or scorched traces. Measure DC voltage on 12V and 5V test points. Disconnect loads individually to locate short. Press and hold the Start/Reset button for 3 seconds until '0:01' or 'CL' appears, wait for drain cycle completion, then cycle power off.
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: External condensate drain backflow or siphon restriction E15; condensate water overflows into base pan or triggers continuous pumping.
On Samsung dryers with OptimalDry triple sensor system (temperature, humidity, condenser mesh), and digital inverter heat pump: Kinked or pinched direct-drain rear hose, drain hose inserted too deep into standpipe creating vacuum siphon, or blocked non-return valve.
Verify drain hose is not pushed more than 10 cm into standpipe; use siphon break bracket. Clean inline rubber non-return flapper valve and ensure unkinked hose path. Power on, touch and hold Dry Level and Time Dry pads simultaneously for 7 seconds until the display chime triggers, then power off.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Power management current limiting relay fault E15; cooktop limits cooking power to single zone or refuses to heat at settings above level 4.
On Samsung cooktops with Virtual Flame LED cooking glow simulation, Flex Zone wide inductors, and detachable magnetic control dial: Pitted or burned contacts on power management selector relay, open relay energizing coil (~350–550 Ω), or failed coil driver transistor.
Measure resistance of relay drive coil (~350–550 Ω). Check contact resistance across switched terminals when energized (<0.1 Ω). Replace relay or inverter board. Remove all cookware and liquids from glass. Power down circuit breaker for 60 seconds, restore power and press Control Lock for 4 seconds.
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Steam generator water level sensor anomaly E15; oven falsely reports empty water reservoir or overfills boiler chamber.
On Samsung ovens with Dual Cook Flex articulated divider door, dual hot-air convection fans, and SmartThings culinary telemetry: Conductive mineral scaling bridging dual level probes, reed switch float jammed by sediment, or detached sense wire.
Clean stainless level probe rods with concentrated citric acid descaler. Check float freedom in reservoir. Measure signal wire continuity to electronic board (<0.5 Ω). Turn off selector dial, unplug oven power cord or switch off main fuse for 5 minutes, reconnect power and configure initial clock time.
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Multi-temperature convertible pantry drawer sensor fault E15; meat/fish or deli drawer temperature setting cannot be regulated.
On Samsung refrigeration units with Twin Cooling Plus independent dual evaporators, Metal Cooling retention plate, and Digital Inverter compressor: Open or shorted NTC sensor embedded in custom-chill drawer housing (~5–10 kΩ at 25°C), or pinched wire harness in drawer rail.
Remove pantry drawer. Check sensor wiring along telescoping rails for chafing. Measure sensor resistance: expected ~16 kΩ at 0°C (~5–10 kΩ at 25°C). Press and hold Power Freeze and Power Cool buttons simultaneously for 8 seconds until the display flashes and clears stored fault codes.
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Mains undervoltage fault E15; power supply input voltage drops below operational threshold (<185V AC) during cycle.
On Samsung washing machines featuring EcoBubble foam generator, Digital Inverter BLDC drive motor, and VRT Plus active vibration reduction: Heavy household line load, loose electrical wall socket connections, or undersized extension power cords.
Measure AC voltage at electrical outlet with multimeter (must be 230V ±10%). Remove extension leads. Connect appliance directly into dedicated outlet. Power on, press and hold Spin Speed and Temperature keys together for 7 seconds until display clears or sounds a melody, then restart cycle.
Samsung OptimalDry / Bespoke AI Heat Pump Tumble Dryer: Automated condenser flush cleaning valve failure E16; self-cleaning wash cycle fails to flush lint from heat pump exchanger.
On Samsung dryers with OptimalDry triple sensor system (temperature, humidity, condenser mesh), and digital inverter heat pump: Open or shorted solenoid actuator coil on condenser flushing valve (~3.5–4.8 kΩ), mechanical scale calcification, or clogged flush nozzle.
Disconnect valve electrical leads. Measure solenoid coil resistance (~3.5–4.8 kΩ). Inspect water flush distributor channel and clear lint debris with nylon brush. Power on, touch and hold Dry Level and Time Dry pads simultaneously for 7 seconds until the display chime triggers, then power off.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Residual heat indicator 'H' stuck illuminated E16; display shows hot glass warning permanently even after cooktop is cold for hours.
On Samsung cooktops with Virtual Flame LED cooking glow simulation, Flex Zone wide inductors, and detachable magnetic control dial: Open or shorted zone temperature sensor holding simulated heat threshold, or microcontroller memory register latchup.
Cut mains power at breaker for 10 minutes to clear register memory. If 'H' returns immediately when power restored, measure zone NTC probe resistance (~100 kΩ at 25°C). Remove all cookware and liquids from glass. Power down circuit breaker for 60 seconds, restore power and press Control Lock for 4 seconds.
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Motorized rotisserie spit drive stall E16; spit does not rotate when inserted into drive coupling during rotisserie program.
On Samsung ovens with Dual Cook Flex articulated divider door, dual hot-air convection fans, and SmartThings culinary telemetry: Stripped metallic internal gear pinion, burned synchronous rotisserie motor winding (~8–14 kΩ), or spit overloaded beyond weight limit.
Remove spit and inspect rear drive hub. Measure rotisserie motor resistance across terminals (~8–14 kΩ). Verify 230V AC supply arrives at motor in grill mode. Turn off selector dial, unplug oven power cord or switch off main fuse for 5 minutes, reconnect power and configure initial clock time.
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Door display to main power board serial communication failure E16; exterior touch interface goes black or flashes communication error.
On Samsung refrigeration units with Twin Cooling Plus independent dual evaporators, Metal Cooling retention plate, and Digital Inverter compressor: Damaged door hinge wire harness flexed repeatedly during door openings, or pin corrosion in top hinge terminal block.
Remove top hinge plastic cover. Inspect multi-pin harness for pinched or broken wires. Test continuity of each line (<0.3 Ω). Verify 12V and 5V DC supplies to door board. Press and hold Power Freeze and Power Cool buttons simultaneously for 8 seconds until the display flashes and clears stored fault codes.
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Suds overdosing detected E16; excessive foam buildup inhibits pump drainage and prolongs rinse cycle safety times.
On Samsung washing machines utilizing EcoBubble foam generator, Digital Inverter BLDC drive motor, and VRT Plus active vibration reduction: Overdosing of high-foaming concentrated detergent, manual hand-wash powder use, or soft water overdosing.
Allow foam to dissipate. Run an empty drum rinse & drain cycle without soap. Clean pressure bell tube. Reduce detergent dosage according to water hardness. Power on, press and hold Spin Speed and Temperature keys together for 7 seconds until display clears or sounds a melody, then restart cycle.
Electronic Control Board (PCB) & Bus Communications
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Internal lighting driver or dimmer circuit fault E17; cavity halogen lamps or LED spots flicker constantly or fail to illuminate.
On Samsung ovens with Dual Cook Flex articulated divider door, dual hot-air convection fans, and SmartThings culinary telemetry: Blown lighting triac on power PCB caused by shorted halogen bulb filament, defective 12V DC switching transformer, or loose lamp socket.
Disconnect power. Remove bulb glass covers; test bulbs with multimeter continuity. Check 12V DC output voltage from light driver module or replace damaged triac PCB. Turn off selector dial, unplug oven power cord or switch off main fuse for 5 minutes, reconnect power and configure initial clock time.
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Inverter module AC supply undervoltage lockout E17; compressor controller disables motor drive to protect power silicon.
On Samsung refrigeration units with Twin Cooling Plus independent dual evaporators, Metal Cooling retention plate, and Digital Inverter compressor: AC input voltage falling below 185V AC under heavy compressor starting torque, or degraded bulk DC bus electrolytic capacitors.
Measure AC voltage at electrical outlet under compressor startup. Measure DC bus voltage across bulk capacitors: must read ~310–340V DC smoothly without excessive ripple. Press and hold Power Freeze and Power Cool buttons simultaneously for 8 seconds until the display flashes and clears stored fault codes.
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Drum positioning error E17; automatic drum parking sensor fails to align opening flaps with the top access lid.
On Samsung washing machines featuring EcoBubble foam generator, Digital Inverter BLDC drive motor, and VRT Plus active vibration reduction: Dislodged drum pulley magnet, open Reed switch sensor, or slipping drive belt preventing fine motor indexing.
Inspect drum drive pulley magnet. Test continuity across Reed sensor contacts while rotating pulley by hand. Inspect and tighten motor drive belt. Power on, press and hold Spin Speed and Temperature keys together for 7 seconds until display clears or sounds a melody, then restart cycle.
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: 3D vibration telemetry fault E18; electronic controller receives out-of-range acceleration signals from chassis motion sensor.
On Samsung washing machines utilizing EcoBubble foam generator, Digital Inverter BLDC drive motor, and VRT Plus active vibration reduction: Unclipped 3D accelerometer sensor bracket, broken internal piezoelectric bridge, or pinched sensor ribbon cable.
Inspect 3D sensor mounting clip on outer tub. Verify sensor cable harness connections. Measure DC reference voltage at sensor connector (5V DC). Power on, press and hold Spin Speed and Temperature keys together for 7 seconds until display clears or sounds a melody, then restart cycle.
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Hot water intake fault E19; secondary hot water inlet valve fails to supply water within allocated filling phase.
On Samsung washing machines featuring EcoBubble foam generator, Digital Inverter BLDC drive motor, and VRT Plus active vibration reduction: Closed hot water tap, sediment-blocked hot inlet filter, or open hot solenoid coil (~3.6–4.6 kΩ).
Check hot water tap supply. Clean the hot inlet hose mesh filter. Measure electrical resistance of hot solenoid coil (~3.6–4.6 kΩ). Power on, press and hold Spin Speed and Temperature keys together for 7 seconds until display clears or sounds a melody, then restart cycle.
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Recirculation spray failure E20; EcoSpray jet pump fails to recirculate detergent solution onto top of laundry load.
On Samsung washing machines utilizing EcoBubble foam generator, Digital Inverter BLDC drive motor, and VRT Plus active vibration reduction: Lint clogging recirculation spray nozzle, seized circulation impeller, or open jet pump winding (~110–180 Ω).
Clear recirculation spray nozzle located at top door bellow. Inspect pump impeller for debris. Measure circulation pump resistance (~110–180 Ω). Power on, press and hold Spin Speed and Temperature keys together for 7 seconds until display clears or sounds a melody, then restart cycle.
On Samsung Hob: The internal components of the induction hob have overheated.
On Samsung Hob: Ensure cookware is appropriate and ventilation slots are not blocked. Allow the hob to cool down completely. If it repeats, service is needed.
Electronic Control Board (PCB) & Bus Communications
Samsung F-1: Operational cycle fault detected during Oven / Microwave program execution.
On Samsung Oven: Internal communication error or failure on the main electronic control board (PBA).
On Samsung Oven: Reset the oven by turning off its circuit breaker for 5 minutes. If the error returns, the control board will likely need to be replaced by a technician.
On Samsung dishwashers utilizing WaterWall sweeping linear spray bar, StormWash rotating nozzle cluster, and auto-release door opening: Internal winding turn short in circulation pump stator, corroded connector pins, or blown output MOSFET on inverter.
Disconnect circulation pump plug. Measure phase resistances across U-V, V-W, U-W with precision ohmmeter (all values must match within ±0.3 Ω, ~48–92 Ω). Press and hold the Start/Reset button for 3 seconds until '0:01' or 'CL' appears, wait for drain cycle completion, then cycle power off.
On Samsung dryers with OptimalDry triple sensor system (temperature, humidity, condenser mesh), and digital inverter heat pump: Severely blocked condenser preventing condensation, restricted capillary tube expansion valve, or high-pressure refrigerant migration.
Allow appliance to cool for 60 minutes. Clean all lint filters and thoroughly degrease heat exchanger fins. Measure discharge line NTC (~50 kΩ at 25°C). Power on, touch and hold Dry Level and Time Dry pads simultaneously for 7 seconds until the display chime triggers, then power off.
Samsung Virtual Flame / Chef Collection Flex Zone Induction Cooktop: Gate driver circuit failure on induction power bridge F01; cooktop disables half of all cooking zones and displays service code.
On Samsung cooktops with Virtual Flame LED cooking glow simulation, Flex Zone wide inductors, and detachable magnetic control dial: Blown gate driver IC, burned SMD gate resistors (nominally 10–22 Ω), or shorted protective Zener clamp diode.
Inspect gate resistor values with multimeter (~10–22 Ω). Check gate-to-emitter diodes. Replace damaged surface mount drive components or renew power generator module. Remove all cookware and liquids from glass. Power down circuit breaker for 60 seconds, restore power and press Control Lock for 4 seconds.
Samsung Dual Cook Flex / Infinite Line / Bespoke Convection Oven: Heating element relay stuck closed runaway condition F01; cavity continues heating uncontrollably even after turning oven off.
On Samsung ovens with Dual Cook Flex articulated divider door, dual hot-air convection fans, and SmartThings culinary telemetry: Heavy electrical arcing welded contacts of 16A power relay on PCB closed, creating unswitched circuit to heating elements.
Instantly trip oven circuit breaker! With power off, test continuity across relay output pins: must be open (infinite Ω). Replace defective relay or power board. Turn off selector dial, unplug oven power cord or switch off main fuse for 5 minutes, reconnect power and configure initial clock time.
Samsung Twin Cooling Plus / Family Hub / Bespoke French Door Refrigerator: Linear inverter compressor piston stroke feedback anomaly F01; compressor clatters loudly or shuts down due to stroke limit breach.
On Samsung refrigeration units with Twin Cooling Plus independent dual evaporators, Metal Cooling retention plate, and Digital Inverter compressor: Resonant spring fatigue inside linear compressor, open stroke sensor feedback coil, or internal valve reed fracture.
Inspect compressor current waveform. Measure compressor winding resistance (~6–10 Ω). If internal mechanical clatter persists, replace linear compressor and update drive software. Press and hold Power Freeze and Power Cool buttons simultaneously for 8 seconds until the display flashes and clears stored fault codes.
Samsung EcoBubble / AddWash / Bespoke AI Digital Inverter Washer: Motor phase imbalance fault F01; 3-phase BLDC motor inverter detects missing phase or unequal current consumption across UVW.
On Samsung washing machines featuring EcoBubble foam generator, Digital Inverter BLDC drive motor, and VRT Plus active vibration reduction: Open stator winding on motor phase U, V, or W, broken connector pin, or blown IGBT output driver channel.
Disconnect motor plug. Measure winding resistance across pairs U-V, V-W, and U-W with multimeter (all must read identical value ±0.2 Ω, ~5.5–11.5 Ω). Power on, press and hold Spin Speed and Temperature keys together for 7 seconds until display clears or sounds a melody, then restart cycle.