OEM VERIFIED BENCH

OFFICIAL FAULT CODEE2

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E2

HobNTC Temperature Sensor & Thermistor

Integrated luxury convection oven and induction cooktop with illuminated touch controls

Hob

Other Brands Sharing Code E2:BoschE2 SiemensE2 LGE2 WhirlpoolE2 ElectroluxE2 AEGE2 BekoE2 HaierE2 CandyE2 NeffE2

Symptom / Description

FAULT

Faure FIE / Induction Duo / Vitroceramic Cooktop: Induction coil overheating alarm E2; induction zone temperature sensor exceeds allowable safety cutoff limit (> 240°C).

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Faure (Faure FIE / Induction Duo / Vitroceramic Cooktop) models: Empty pan boiled dry at maximum boost power, non-induction pan with thin base concentrating extreme heat, or degraded silicone heat-sink paste on coil NTC.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Switch off cooking zone and allow hob to cool down for 20 minutes. Inspect cookware suitability with a magnet. Verify coil NTC resistance (~100 kΩ at 25°C). Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorHob / Cooktop

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E2

FAQ TREE

What does error code E2 mean on a Faure appliance?

Faure error code E2 indicates: Faure FIE / Induction Duo / Vitroceramic Cooktop: Induction coil overheating alarm E2; induction zone temperature sensor exceeds allowable safety cutoff limit (> 240°C)..

What is the root cause of Faure error code E2?

The primary root cause for Faure code E2 is: On Faure (Faure FIE / Induction Duo / Vitroceramic Cooktop) models: Empty pan boiled dry at maximum boost power, non-induction pan with thin base concentrating extreme heat, or degraded silicone heat-sink paste on coil NTC..

How do I fix or resolve Faure error code E2?

To resolve error code E2: Switch off cooking zone and allow hob to cool down for 20 minutes. Inspect cookware suitability with a magnet. Verify coil NTC resistance (~100 kΩ at 25°C). Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

Is it safe to clear Faure error code E2 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Faure code E2 persists, the physical component causing On Faure (Faure FIE / Induction Duo / Vitroceramic Cooktop) models: Empty pan boiled dry at maximum boost power, non-induction pan with thin base concentrating extreme heat, or degraded silicone heat-sink paste on coil NTC. must be inspected or replaced.

How do I test electrical resistance for Faure code E2 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test NTC Temperature Sensor Probe (Thermistor) across Across sensor pins 1-2 (unplugged harness). Expected nominal reading is 4.8kΩ–12kΩ (at 20°C–25°C). Tolerance: Negative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit..

What safety protocol must be followed before servicing Faure code E2?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE2

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E2

HobNTC Temperature Sensor & Thermistor

Hob

Other Brands Sharing Code E2:BoschE2 SiemensE2 LGE2 WhirlpoolE2 ElectroluxE2 AEGE2 BekoE2 HaierE2 CandyE2 NeffE2

Symptom / Description

FAULT

Faure FIE / Induction Duo / Vitroceramic Cooktop: Induction coil overheating alarm E2; induction zone temperature sensor exceeds allowable safety cutoff limit (> 240°C).

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLNTC Temperature Sensor & ThermistorHob / Cooktop

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

4.8kΩ–12kΩ (at 20°C–25°C)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:NTC Temperature Sensor Probe (Thermistor)

Test Pins & Connections

PROBE (+)

PROBE (-)

Across sensor pins 1-2 (unplugged harness)

Tolerance & Diagnostic CriteriaNegative temperature coefficient: resistance drops smoothly when warmed with fingers. OL = open circuit.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Disconnect 230V electrical mains power before removing appliance side or rear panels.
!Ensure tub water or heating chamber has cooled below 30°C before unclipping thermistor probe.
!Use CAT III 600V/1000V insulated test probes when tng at PCB edge connectors.

3. Preliminary Mechanical & Visual Checks

Inspect sensor immersion sleeve for calcification, limescale scale, or thermal paste degradation.
Check wiring harness for pinch points, chafing against chassis metal, and terminal pin oxidation.
Verify probe is firmly seated in its rubber grommet or bracket inside the water/air circuit.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E2

FAQ TREE

What does error code E2 mean on a Faure appliance?

What is the root cause of Faure error code E2?

How do I fix or resolve Faure error code E2?

Is it safe to clear Faure error code E2 by resetting power?

How do I test electrical resistance for Faure code E2 using a multimeter?

What safety protocol must be followed before servicing Faure code E2?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Faure E2

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E2

Community Verification

Related Faure Hob / Cooktop Error Codes

Faure E2

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E2

Community Verification

Related Faure Hob / Cooktop Error Codes