OEM VERIFIED BENCH

OFFICIAL FAULT CODEE7

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E7

HobDrive Motor, Inverter & Tachometer Sensor

Integrated luxury convection oven and induction cooktop with illuminated touch controls

Hob

Other Brands Sharing Code E7:BoschE7 LGE7 ElectroluxE7 AEGE7 HaierE7 CandyE7 HooverE7 ZanussiE7 BrandtE7 Arthur MartinE7

Symptom / Description

FAULT

Faure FIE / Induction Duo / Vitroceramic Cooktop: Hob cooling fan motor fault E7; internal 12V DC cooling fan does not run or tachometer pulse signal is absent.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Faure (Faure FIE / Induction Duo / Vitroceramic Cooktop) models: Defective brushless fan motor, fan blades seized by stray wire or foreign debris, unseated fan connector, or blown fan driver circuit on PCB.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Inspect fan assembly. Spin blades by hand to verify smooth rotation. Measure 12V DC across fan pins during zone operation. Replace fan if seized. Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorHob / Cooktop

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E7

FAQ TREE

What does error code E7 mean on a Faure appliance?

Faure error code E7 indicates: Faure FIE / Induction Duo / Vitroceramic Cooktop: Hob cooling fan motor fault E7; internal 12V DC cooling fan does not run or tachometer pulse signal is absent..

What is the root cause of Faure error code E7?

The primary root cause for Faure code E7 is: On Faure (Faure FIE / Induction Duo / Vitroceramic Cooktop) models: Defective brushless fan motor, fan blades seized by stray wire or foreign debris, unseated fan connector, or blown fan driver circuit on PCB..

How do I fix or resolve Faure error code E7?

To resolve error code E7: Inspect fan assembly. Spin blades by hand to verify smooth rotation. Measure 12V DC across fan pins during zone operation. Replace fan if seized. Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

Is it safe to clear Faure error code E7 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Faure code E7 persists, the physical component causing On Faure (Faure FIE / Induction Duo / Vitroceramic Cooktop) models: Defective brushless fan motor, fan blades seized by stray wire or foreign debris, unseated fan connector, or blown fan driver circuit on PCB. must be inspected or replaced.

How do I test electrical resistance for Faure code E7 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test 3-Phase Motor Windings / Tacho Generator / Carbon Brushes across Across phase pins U-V, V-W, U-W on motor harness; across tacho pins. Expected nominal reading is 3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator). Tolerance: BLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho..

What safety protocol must be followed before servicing Faure code E7?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE7

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E7

HobDrive Motor, Inverter & Tachometer Sensor

Hob

Other Brands Sharing Code E7:BoschE7 LGE7 ElectroluxE7 AEGE7 HaierE7 CandyE7 HooverE7 ZanussiE7 BrandtE7 Arthur MartinE7

Symptom / Description

FAULT

Faure FIE / Induction Duo / Vitroceramic Cooktop: Hob cooling fan motor fault E7; internal 12V DC cooling fan does not run or tachometer pulse signal is absent.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrive Motor, Inverter & Tachometer SensorHob / Cooktop

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

3Ω–6Ω (BLDC phase U-V-W) / 60Ω–180Ω (Tacho coil) / 1.5Ω–3.5Ω (Universal stator)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:3-Phase Motor Windings / Tacho Generator / Carbon Brushes

Test Pins & Connections

PROBE (+)

PROBE (-)

Across phase pins U-V, V-W, U-W on motor harness; across tacho pins

Tolerance & Diagnostic CriteriaBLDC phase winding values must be strictly balanced within ±0.3Ω. Hand rotation generates 1V–4V AC on tacho.

1. Pre-Intervention Electrical Safety Protocols

!High-Voltage Safety Protocol & DC Bus: Wait at least 5 minutes after power cutoff to allow inverter DC bus capacitors (380V DC) to bleed down.
!Verify 0V DC across inverter filter capacitors before unplugging motor harness connectors.
!Keep hands clear of drive belt and pulleys during any manual rotation tng.

3. Preliminary Mechanical & Visual Checks

Slip off drive belt and spin drum/motor shaft by hand to check for roaring or seized ball bearings.
For universal motors: verify carbon brushes have at least 10mm remaining length and smooth contact faces.
Inspect motor suspension rubber mounts and drive belt tension/groove profile.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E7

FAQ TREE

What does error code E7 mean on a Faure appliance?

Faure error code E7 indicates: Faure FIE / Induction Duo / Vitroceramic Cooktop: Hob cooling fan motor fault E7; internal 12V DC cooling fan does not run or tachometer pulse signal is absent..

What is the root cause of Faure error code E7?

How do I fix or resolve Faure error code E7?

Is it safe to clear Faure error code E7 by resetting power?

How do I test electrical resistance for Faure code E7 using a multimeter?

What safety protocol must be followed before servicing Faure code E7?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Faure E7

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E7

Community Verification

Related Faure Hob / Cooktop Error Codes

Faure E7

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E7

Community Verification

Related Faure Hob / Cooktop Error Codes