OEM VERIFIED BENCH

OFFICIAL FAULT CODEE24

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E24

Washing MachineDrainage System & Drain Pump

Washing Machine

Other Brands Sharing Code E24:BoschE24 SiemensE24 ElectroluxE24 AEGE24 NeffE24 ZanussiE24 Arthur MartinE24 GaggenauE24 CastorE24 FrigidaireE24

Symptom / Description

FAULT

Faure FWG / FWF Series / Magic'45 Compact Washer: Drain pump sensing feedback circuit error E24; microprocessor reads incorrect sensing voltage across pump line.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: Drain pump disconnected or open circuit (infinite Ω), broken copper wire in harness, or defective sensing divider resistors on motherboard.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Verify wiring continuity from main PCB connector J1 to drain pump terminals. Measure pump coil resistance (nominal 160–220 Ω). Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E24

FAQ TREE

What does error code E24 mean on a Faure appliance?

Faure error code E24 indicates: Faure FWG / FWF Series / Magic'45 Compact Washer: Drain pump sensing feedback circuit error E24; microprocessor reads incorrect sensing voltage across pump line..

What is the root cause of Faure error code E24?

The primary root cause for Faure code E24 is: On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: Drain pump disconnected or open circuit (infinite Ω), broken copper wire in harness, or defective sensing divider resistors on motherboard..

How do I fix or resolve Faure error code E24?

To resolve error code E24: Verify wiring continuity from main PCB connector J1 to drain pump terminals. Measure pump coil resistance (nominal 160–220 Ω). Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

Is it safe to clear Faure error code E24 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Faure code E24 persists, the physical component causing On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: Drain pump disconnected or open circuit (infinite Ω), broken copper wire in harness, or defective sensing divider resistors on motherboard. must be inspected or replaced.

How do I test electrical resistance for Faure code E24 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Drain Pump Motor Stator Coils across Across pump motor spade terminals (L-N unclipped). Expected nominal reading is 160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC). Tolerance: ±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ..

What safety protocol must be followed before servicing Faure code E24?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE24

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E24

Washing MachineDrainage System & Drain Pump

Washing Machine

Other Brands Sharing Code E24:BoschE24 SiemensE24 ElectroluxE24 AEGE24 NeffE24 ZanussiE24 Arthur MartinE24 GaggenauE24 CastorE24 FrigidaireE24

Symptom / Description

FAULT

Faure FWG / FWF Series / Magic'45 Compact Washer: Drain pump sensing feedback circuit error E24; microprocessor reads incorrect sensing voltage across pump line.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLDrainage System & Drain PumpWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

160Ω–220Ω (Sync 230V) / 20Ω–45Ω (3-Phase BLDC)NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Drain Pump Motor Stator Coils

Test Pins & Connections

PROBE (+)

PROBE (-)

Across pump motor spade terminals (L-N unclipped)

Tolerance & Diagnostic Criteria±10% balance. Insulation resistance between coil and motor chassis must exceed 20MΩ.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Isolate 230V mains power before accessing the lower pump housing.
!Prepare a shallow basin and absorption towels: expect 3 to 10 liters of stagnant trapped water upon filter opening.
!Beware of sharp foreign objects (broken glass, needles, screws) trapped inside the impeller cavity.

3. Preliminary Mechanical & Visual Checks

Unscrew coin trap filter and clear all foreign debris (coins, hairpins, bra underwires).
Rotate pump impeller manually: synchronous magnetic rotors should snap cleanly in 90° intervals without jamming.
Check drain hose for kinks, blockages, or unpunched sink spigots; verify drain height is between 65cm and 100cm.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E24

FAQ TREE

What does error code E24 mean on a Faure appliance?

Faure error code E24 indicates: Faure FWG / FWF Series / Magic'45 Compact Washer: Drain pump sensing feedback circuit error E24; microprocessor reads incorrect sensing voltage across pump line..

What is the root cause of Faure error code E24?

How do I fix or resolve Faure error code E24?

Is it safe to clear Faure error code E24 by resetting power?

How do I test electrical resistance for Faure code E24 using a multimeter?

What safety protocol must be followed before servicing Faure code E24?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Faure E24

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E24

Community Verification

Related Faure Washing Machine Error Codes

Faure E24

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E24

Community Verification

Related Faure Washing Machine Error Codes