Access our premium database of error codes, common faults, and professional repair solutions for Indesit appliances.
On Indesit Dishwasher: Dishwasher stops and beeps, water in the base
On Indesit Dishwasher: Leak detected and anti-flood system activated.
On Indesit Dishwasher: Disconnect from power. Tilt the dishwasher to drain water from the base tray. Find and repair the source of the leak (hoses, seals, etc.).
Indesit Total NoFrost & Pure Wind Refrigerator: High temperature warning A1; freezer compartment temperature has risen above -9°C (15°F), alerting user of thermal compromise.
On Indesit refrigerators (Indesit Push&Go one-touch architecture and Arcadia 2/3 / EVO-II microprocessor control platform): Door left open, damaged magnetic perimeter gasket, excessive quantity of warm fresh groceries introduced, or early refrigerant leak.
Ensure freezer door seals completely. Inspect magnetic gasket with paper slip test. Press Alarm Reset button to mute buzzer. Allow 6 to 12 hours for cool-down. Press and hold Super Cool / Reset button for 5 seconds until indicator stops blinking and compressor engages.
On Indesit Dishwasher: Dishwasher fails to fill with water
On Indesit Dishwasher: Water inlet valve (solenoid) fault.
On Indesit Dishwasher: Check that the water supply is on. Clean inlet hose filters. Test the inlet valve solenoid for resistance; replace if faulty.
Indesit Total NoFrost & Pure Wind Refrigerator: Critical high temperature alarm A2 indicates food danger; freezer temperature climbed above -1°C, risking thawing of frozen perishables.
On Indesit refrigerators (Indesit Push&Go one-touch architecture and Arcadia 2/3 / EVO-II microprocessor control platform): Long power outage, catastrophic refrigeration circuit leak (R600a), seized compressor, or broken evaporator fan motor.
Do not refreeze thawed perishables. Check if compressor and evaporator fan are running. Press alarm silence button to dismiss code and restore cooling. Press and hold Super Cool / Reset button for 5 seconds until indicator stops blinking and compressor engages.
On Indesit Dishwasher: Dishwasher does not drain, water left at the bottom
On Indesit Dishwasher: Drain timeout. The machine is taking too long to empty the water.
On Indesit Dishwasher: Clean the filters. Check the drain pump for blockages. Ensure the drain hose is not kinked or blocked.
On Indesit Dishwasher: Water not heating or cycle takes too long
On Indesit Dishwasher: NTC (temperature sensor) fault. The machine cannot read the water temperature correctly.
On Indesit Dishwasher: Test the NTC sensor and its wiring. Replace the sensor if its resistance is incorrect.
On Indesit Dishwasher: Dishes are not being cleaned properly
On Indesit Dishwasher: Pressure switch fault or circulation pump blockage. The machine detects that the spray arms are not rotating correctly.
On Indesit Dishwasher: Check and clean filters. Ensure spray arms are not blocked and can spin freely. Inspect the wash motor/circulation pump for blockages.
On Indesit Dishwasher: Dishwasher stops early in the cycle, no water inside
On Indesit Dishwasher: Water fill timeout. Similar to H20 in washing machines.
On Indesit Dishwasher: Verify water supply is on and pressure is adequate. Check inlet hose for kinks and clean the filter screen at the valve connection.
On Indesit Dishwasher: Water is not being directed to the correct spray arm
On Indesit Dishwasher: Diverter valve fault. The device that alternates water flow between the upper and lower spray arms is stuck or faulty.
On Indesit Dishwasher: Inspect the diverter valve motor and mechanism for blockages or failure. Check wiring to the valve.
On Indesit Dishwasher: Water is cold, dishes remain dirty
On Indesit Dishwasher: Wash heater fault. The heating element is not working.
On Indesit Dishwasher: Test the heating element for continuity. Check for burnt wiring or a faulty relay on the main control board.
On Indesit Dishwasher: Machine stops and beeps, may not have filled
On Indesit Dishwasher: Fill valve or heater circuit error. The board has detected a fault in either the water inlet solenoid or the heating element circuit.
On Indesit Dishwasher: This is a complex error. Check both the fill valve and the heating element circuits for faults. If both are okay, the main board is likely the issue.
Indesit Total NoFrost & Pure Wind Refrigerator: Fresh food compartment evaporator NTC thermistor sensor fault AL01; circuit reading out of calibrated limits.
On Indesit refrigerators (Indesit Push&Go one-touch architecture and Arcadia 2/3 / EVO-II microprocessor control platform): Water ingress into thermal sensor epoxy potting, fractured copper leads behind liner, or corrosion on terminal pin J1.
Unplug unit. Access sensor behind rear baffle. Measure NTC resistance: nominal ~2.7 kΩ at 25°C, ~7.8 kΩ at 4°C, ~16 kΩ at 0°C. Replace sensor probe. Press and hold Super Cool / Reset button for 5 seconds until indicator stops blinking and compressor engages.
Indesit Total NoFrost & Pure Wind Refrigerator: Freezer evaporator defrost termination NTC sensor fault AL02; controller unable to detect coil temperature.
On Indesit refrigerators (Indesit Push&Go one-touch architecture and Arcadia 2/3 / EVO-II microprocessor control platform): Thermal shock degradation, moisture saturation inside sensor jacket during defrost cycles, or severed clip-on lead.
Disconnect power. Remove freezer evaporator cover. Check NTC resistance: ~2.7 kΩ at 25°C, ~16 kΩ at 0°C, ~32 kΩ at -18°C. Replace clip-on defrost sensor. Press and hold Super Cool / Reset button for 5 seconds until indicator stops blinking and compressor engages.
Indesit Total NoFrost & Pure Wind Refrigerator: Freezer compartment air ambient temperature sensor fault AL03; compressor runs continuously in emergency mode.
On Indesit refrigerators (Indesit Push&Go one-touch architecture and Arcadia 2/3 / EVO-II microprocessor control platform): Open circuit or shorted NTC thermistor bead, damaged wiring behind rear freezer wall, or main board ADC port defect.
Isolate electrical supply. Measure air probe resistance across main PCB connector: ~32 kΩ at -18°C, ~16 kΩ at 0°C. If open/short, replace sensor. Press and hold Super Cool / Reset button for 5 seconds until indicator stops blinking and compressor engages.
Indesit Innex & Push&Go MyTime Washing Machine: Drum doors open during cycle BDD; top-loader drum flaps opened or unlatched during wash tumble motion.
On Indesit top-loading washing machines: Mechanical flap spring lock failure, laundry item snagged between gates, or drum positioning sensor mismatch.
Isolate power. Manually rotate drum until flaps face top opening. Check catch springs for positive latch tension. Ensure no laundry pinches the latch. Press and hold Start/Pause for 5 seconds until LEDs sequence, rotate selector to '0', and disconnect power for 60s.
Indesit Aria Induction & Ceramic Dual Zone Cooktop: Touch control panel thermal warning C81; temperature sensor beneath front glass panel senses heat exceeding 75°C.
On Indesit cooktops: Hot pan shifted or placed onto front touch sensor glass area, or heat radiating from large griddle pan overlapping controls.
Immediately move hot cookware away from front glass control area. Leave hob off for 5–10 minutes until sensor cools below 60°C. Disconnect mains power for 60 seconds, verify sensor glass area is completely dry, then reconnect.
Indesit Aria Induction & Ceramic Dual Zone Cooktop: Electronic power module thermal overload C82; heatsink temperature reaches 90°C during extended multi-zone booster operation.
On Indesit cooktops: Inadequate cabinet ventilation below cooktop base, clogged cooling fan intake vents, or high ambient kitchen temperature.
Allow zones to operate at reduced power levels. Ensure intake fan underneath chassis has unhindered fresh air supply. Clean chassis dust filters. Disconnect mains power for 60 seconds, verify sensor glass area is completely dry, then reconnect.
Indesit Aria Induction & Ceramic Dual Zone Cooktop: Mains supply undervoltage trip C83; inverter filter bridge senses line voltage dipping below 170V during heavy induction draw.
On Indesit cooktops: Undersized electrical feeder cables from consumer unit, loose neutral clamp in distribution box, or high grid load.
Check electrical feeder wire gauge (minimum 2.5 mm² for 16A, 4.0 mm² for 32A). Tighten terminal connections in junction box and measure voltage drop under load. Disconnect mains power for 60 seconds, verify sensor glass area is completely dry, then reconnect.
Indesit Aria Induction & Ceramic Dual Zone Cooktop: Mains overvoltage detected across filter stage C84; line voltage surge protective circuit trips above 275V RMS.
On Indesit cooktops: Open neutral conductor on 400V 3-phase supply causing floating phase voltage, or lightning grid transient surge.
Isolate cooktop immediately to protect electronics. Measure phase-to-neutral voltage with true-RMS meter (must not exceed 250V AC). Verify solid Neutral bond. Disconnect mains power for 60 seconds, verify sensor glass area is completely dry, then reconnect.
Indesit Aria Induction & Ceramic Dual Zone Cooktop: Incompatible cookware detected by induction coil sensing C85; pan ferromagnetic property insufficient for stable resonance.
On Indesit cooktops: Warped pan base with air gap over glass, pan diameter too small (< 100mm for selected zone), or composite non-magnetic base alloy.
Use heavy-gauge flat-bottomed induction-rated cookware. Verify magnet strongly attaches to entire base surface. Center pan over matching zone diameter ring. Disconnect mains power for 60 seconds, verify sensor glass area is completely dry, then reconnect.
Indesit Total NoFrost & Pure Wind Refrigerator: Communication error CE between console display circuit board and main refrigerator control module.
On Indesit refrigerators (Indesit Push&Go one-touch architecture and Arcadia 2/3 / EVO-II microprocessor control platform): Broken serial data wire in door harness, intermittent 5V DC power feed from power supply, or electromagnetic interference on bus.
Disconnect mains power for 60 seconds. Inspect wiring through door hinge. Check 5V DC rail at display connector. Replace damaged interconnect harness. Press and hold Super Cool / Reset button for 5 seconds until indicator stops blinking and compressor engages.
Indesit Total NoFrost & Pure Wind Refrigerator: Serial communication failure CF between user interface display panel and main power control module.
On Indesit refrigerators (Indesit Push&Go one-touch architecture and Arcadia 2/3 / EVO-II microprocessor control platform): Severed or pinched door hinge ribbon wiring harness, oxidised molex pins, or corrupted display controller firmware.
Disconnect mains power. Inspect door hinge wiring harness for broken wires. Test 5V/12V DC bus supply voltage from main board. Replace damaged harness. Press and hold Super Cool / Reset button for 5 seconds until indicator stops blinking and compressor engages.
Indesit Total NoFrost & Pure Wind Refrigerator: Defrost circuit failure dE; electric heating element failed to warm evaporator coil sufficiently during scheduled defrost cycle.
On Indesit refrigerators (Indesit Push&Go one-touch architecture and Arcadia 2/3 / EVO-II microprocessor control platform): Open-circuit calrod heating element (~160 Ω to 260 Ω), blown in-line thermal fuse (72°C), or stuck defrost relay contacts on PCB.
Disconnect mains. Remove freezer evaporator cover. Measure defrost heater resistance (~160–260 Ω) and thermal fuse continuity (<1 Ω). Replace defective component. Press and hold Super Cool / Reset button for 5 seconds until indicator stops blinking and compressor engages.
Indesit Push&Go & Extra Hygiene DFP Series Dishwasher: Electronic temperature sensing disconnect E1; microcomputer detects sensor resistance above open-circuit limit (> 200 kΩ).
On Indesit dishwashers: Wire fractured in door hinge flex loom, corroded terminals on sump NTC probe, or broken sensor internal connection.
Test wiring harness continuity from control board to NTC probe terminals. Measure NTC thermistor resistance (nominal ~48 kΩ at 25°C). Repair broken wiring loom. Press and hold Start/Reset for 5 seconds until drain pump runs, wait 60 seconds, then power cycle ON/OFF.
Indesit Push&Go & Extra Hygiene DFP Series Dishwasher: AquaStop base pan float switch closed E2; emergency drain activated to prevent residential water flooding.
On Indesit dishwashers: Sump seal failure, loose hose clamp on circulation pump volute, split water matrix air-break, or leaking door lower gasket.
Unplug unit. Sponge dry base tray. Inspect circulation motor and sump gaskets for active drips. Replace defective hydraulic joint or hose. Press and hold Start/Reset for 5 seconds until drain pump runs, wait 60 seconds, then power cycle ON/OFF.
Indesit Push&Go & Extra Hygiene DFP Series Dishwasher: Wash heating circuit open error E3; current transformer or thermal monitor detects zero watt heating draw during heat step.
On Indesit dishwashers: Blown thermal fuse embedded in heater tube terminal, burnt PCB solder joint on heating relay, or disconnected wiring harness.
Measure heating element terminal resistance (nominal 24–29 Ω). Verify continuity of inline safety cutouts (0 Ω). Inspect power board for scorched relay solder pins. Press and hold Start/Reset for 5 seconds until drain pump runs, wait 60 seconds, then power cycle ON/OFF.
Indesit Push&Go & Extra Hygiene DFP Series Dishwasher: Drain evacuation timeout E4; sump pressure switch or virtual sensor indicates tub holds water past 240 seconds drain attempt.
On Indesit dishwashers: Clogged sink spigot connection, kinked discharge pipe, foreign object jamming synchronous drain impeller, or worn magnetic motor rotor.
Clean sink drain barb. Unclip drain hose and test flow into bucket. Remove debris around drain pump impeller. Measure motor coil resistance (160–185 Ω). Press and hold Start/Reset for 5 seconds until drain pump runs, wait 60 seconds, then power cycle ON/OFF.
Indesit Push&Go & Extra Hygiene DFP Series Dishwasher: Circulation pump speed feedback discrepancy E5; inverter drive senses tachometric deviation or stalled impeller.
On Indesit dishwashers: Mineral scale buildup seizing pump shaft graphite bearings, or disconnected 3-phase BLDC motor harness connector.
Spin pump rotor manually to verify free rotation. Measure winding resistance across motor phases (symmetrical ~45–60 Ω). Check inverter voltage outputs. Press and hold Start/Reset for 5 seconds until drain pump runs, wait 60 seconds, then power cycle ON/OFF.
Indesit Push&Go & Extra Hygiene DFP Series Dishwasher: Slow water fill sequence E6; flowmeter counts insufficient volumetric intake within the allotted 5-minute fill window.
On Indesit dishwashers: Partially closed isolation valve, partially blocked inlet hose mesh screen, or low domestic municipal water supply pressure.
Verify water tap delivers at least 2.5 L/min dynamically. Remove inlet hose nut and clean cone filter screen. Replace solenoid inlet valve if flow restricted. Press and hold Start/Reset for 5 seconds until drain pump runs, wait 60 seconds, then power cycle ON/OFF.
Indesit Push&Go & Extra Hygiene DFP Series Dishwasher: Flow sensor open circuit error E7; control board detects broken circuit to water flowmeter reed switch board.
On Indesit dishwashers: Corroded copper tracks or broken wire on 2-pin connector of the water matrix air break flowmeter PCB.
Inspect 2-pin wire harness between power board and flowmeter PCB. Check reed switch continuity while spinning turbine with magnet. Replace reed board. Press and hold Start/Reset for 5 seconds until drain pump runs, wait 60 seconds, then power cycle ON/OFF.
Our official certified partners service Indesit appliances in your area.