OEM VERIFIED BENCH

OFFICIAL FAULT CODEE10

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E10

Washing MachineWater Level Pressure Switch & Air Dome

Washing Machine

Other Brands Sharing Code E10:BoschE10 ElectroluxE10 AEGE10 CandyE10 HooverE10 ZanussiE10 Arthur MartinE10 PhilipsE10 RosieresE10 SauterE10

Symptom / Description

FAULT

Faure FWG / FWF Series / Magic'45 Compact Washer: Water fill timeout alarm E10; appliance fails to reach minimum static wash water level within 5 minutes.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: Inlet water tap closed, kinked inlet hose, clogged solenoid valve filter screen, defective 230V solenoid valve coil (expected 3.5–4.5 kΩ), or open triac on EWM motherboard.

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

1Verify household water pressure (min 1 bar). Unscrew inlet hose and clean mesh filter. Measure solenoid valve coil resistance with multimeter (3.5–4.5 kΩ). Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

AI diagnostic workshop engine analyzing appliance circuit schematics and error telemetry in real time

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Level Pressure Switch & Air DomeWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

Precision digital multimeter probes measuring electrical resistance in Ohms on an appliance control board

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Mechanical Pressure Switch Contacts / Inductive Frequency Sensor

Test Pins & Connections

PROBE (+)

PROBE (-)

Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal

Tolerance & Diagnostic CriteriaMechanical switch contacts must transition cleanly on gentle breath pressure. Coil ~22Ω ±5%.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Cut 230V mains power before accessing the upper chassis or pressure switch terminals.
!Drain appliance tub completely before disconnecting pressure switch sensing hoses.
!Never blow high-pressure compressed air into electronic analog pressure sensors: internal diaphragms will rupture!

3. Preliminary Mechanical & Visual Checks

Disconnect the silicone pressure tube from the lower air trap and inspect for soap sludge, lint, or water blockage.
Inspect the flexible rubber hose along its entire length for pinholes, cracks, or loose clamp fit.
Thoroughly flush the lower compression chamber (air dome) with hot water to dissolve detergent buildup.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E10

FAQ TREE

What does error code E10 mean on a Faure appliance?

Faure error code E10 indicates: Faure FWG / FWF Series / Magic'45 Compact Washer: Water fill timeout alarm E10; appliance fails to reach minimum static wash water level within 5 minutes..

What is the root cause of Faure error code E10?

The primary root cause for Faure code E10 is: On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: Inlet water tap closed, kinked inlet hose, clogged solenoid valve filter screen, defective 230V solenoid valve coil (expected 3.5–4.5 kΩ), or open triac on EWM motherboard..

How do I fix or resolve Faure error code E10?

To resolve error code E10: Verify household water pressure (min 1 bar). Unscrew inlet hose and clean mesh filter. Measure solenoid valve coil resistance with multimeter (3.5–4.5 kΩ). Press and hold Départ/Pause and Annulation buttons for 6 seconds until all status indicators flash synchronously and clear fault memory.

Is it safe to clear Faure error code E10 by resetting power?

Resetting power (unplugging for 5–10 minutes) clears temporary memory errors. However, if Faure code E10 persists, the physical component causing On Faure (Faure FWG / FWF Series / Magic'45 Compact Washer) models: Inlet water tap closed, kinked inlet hose, clogged solenoid valve filter screen, defective 230V solenoid valve coil (expected 3.5–4.5 kΩ), or open triac on EWM motherboard. must be inspected or replaced.

How do I test electrical resistance for Faure code E10 using a multimeter?

Set a digital multimeter to ohms (Ω). Disconnect power and test Mechanical Pressure Switch Contacts / Inductive Frequency Sensor across Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal. Expected nominal reading is Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.. Tolerance: Mechanical switch contacts must transition cleanly on gentle breath pressure. Coil ~22Ω ±5%..

What safety protocol must be followed before servicing Faure code E10?

Standard electrical safety protocol: 1. Disconnect 230V mains power before opening panels. 2. Verify zero voltage at test points. 3. Allow hot water or heating elements to cool below 30°C before handling.

Community Verification

COMMUNITY

Did this solution resolve the issue?

Back to Search

OEM VERIFIED BENCH

OFFICIAL FAULT CODEE10

Faure // OFFICIAL DIAGNOSTIC BENCH

Faure E10

Washing MachineWater Level Pressure Switch & Air Dome

Washing Machine

Other Brands Sharing Code E10:BoschE10 ElectroluxE10 AEGE10 CandyE10 HooverE10 ZanussiE10 Arthur MartinE10 PhilipsE10 RosieresE10 SauterE10

Symptom / Description

FAULT

Faure FWG / FWF Series / Magic'45 Compact Washer: Water fill timeout alarm E10; appliance fails to reach minimum static wash water level within 5 minutes.

TELEMETRY // LIVESIG: FAULT_DETECTED

Root Cause

ROOT CAUSE

CIRCUIT // SUBSYSTEMLOGIC: ROOT_ISOLATED

Repair Instructions

UNLOCKED

AI WORKSHOP PROTOCOL ENGINE

Direct extraction from OEM factory manuals & wiring schematics

Field Actions

DISPATCH

Need Help? Call a Certified Technician Worldwide Faure Parts Finder

Electrical & Safety Protocol

Always disconnect appliance from 230V/400V mains before opening panels. Use CAT III multimeter for circuit testing.

CALIBRATED BENCH PROTOCOL // CAT III 600V

Workshop Verification & Safety Checklist

WORKSHOP VERIFICATION PROTOCOLWater Level Pressure Switch & Air DomeWashing Machine

2. Multimeter & Electrical Bench Tests (Ω)

MODE: OHMMETER (Ω)AUTO-RANGE

CALIBRATED METROLOGY RESISTANCE BENCH (CAT III)

Nominal Resistance (Ω)

Mechanical: Continuity 0.0Ω–0.2Ω (Empty: 11-12, Full: 11-14). Electronic: 20Ω–45Ω coil resistance.NOMINAL

0 Ω (SHORT)CALIBRATED BAND∞ OL (OPEN)

▲ NOMINAL OPERATING WINDOW

Target Component:Mechanical Pressure Switch Contacts / Inductive Frequency Sensor

Test Pins & Connections

PROBE (+)

PROBE (-)

Across switch spade contacts with harness unplugged; electronic output: 40Hz–50Hz frequency signal

Tolerance & Diagnostic CriteriaMechanical switch contacts must transition cleanly on gentle breath pressure. Coil ~22Ω ±5%.

1. Pre-Intervention Electrical Safety Protocols

!Electrical Safety Protocol: Cut 230V mains power before accessing the upper chassis or pressure switch terminals.
!Drain appliance tub completely before disconnecting pressure switch sensing hoses.
!Never blow high-pressure compressed air into electronic analog pressure sensors: internal diaphragms will rupture!

3. Preliminary Mechanical & Visual Checks

Disconnect the silicone pressure tube from the lower air trap and inspect for soap sludge, lint, or water blockage.
Inspect the flexible rubber hose along its entire length for pinholes, cracks, or loose clamp fit.
Thoroughly flush the lower compression chamber (air dome) with hot water to dissolve detergent buildup.

Perform these diagnostic steps before triggering AI Deep Search or replacing boards.Certified Workshop Routine

Frequently Asked Questions: Faure E10

FAQ TREE

What does error code E10 mean on a Faure appliance?

Faure error code E10 indicates: Faure FWG / FWF Series / Magic'45 Compact Washer: Water fill timeout alarm E10; appliance fails to reach minimum static wash water level within 5 minutes..

What is the root cause of Faure error code E10?

How do I fix or resolve Faure error code E10?

Is it safe to clear Faure error code E10 by resetting power?

How do I test electrical resistance for Faure code E10 using a multimeter?

What safety protocol must be followed before servicing Faure code E10?

Community Verification

COMMUNITY

Did this solution resolve the issue?

Faure E10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E10

Community Verification

Related Faure Washing Machine Error Codes

Faure E10

Symptom / Description

Root Cause

Repair Instructions

Field Actions

Workshop Verification & Safety Checklist

Frequently Asked Questions: Faure E10

Community Verification

Related Faure Washing Machine Error Codes