Access our premium database of error codes, common faults, and professional repair solutions for Miele appliances.
The device displays a fault concerning carriage 13 and refuses to continue the program.
The control module is not receiving or receiving incorrect signals from Carriage 13,...
1. Turn off the main power to the device. 2. Check the mechanical movement of carriage 13...
An error code indicating a problem with carriage 14 is displayed, stopping the current process.
Malfunction in the communication or detection circuit of the carriage 14, often linked to a...
1. Turn off the power for safety reasons. 2. Inspect the carriage travel area 14 for...
The device signals a specific error to carriage 15 and the cycle is interrupted.
Loss of communication or positioning error detected on carriage 15, potentially due to a...
1. Disconnect the device from the electrical network. 2. Make sure that nothing obstructs...
The device displays an error indicating that Application Module (AM) 10 was not found.
The main control module fails to communicate with the application module 10. This may be...
1. Turn off the power. 2. Locate application module 10. 3. Verify that the module is...
Error displayed indicating that wash/rinse module (SPÜWAM) 1 is not detected.
Communication problem between the central unit and the wash/rinse module 1. The module may...
1. Turn off the power supply. 2. Identify the location of the SPÜWAM 1 module. 3. Check its...
Error message indicating that conductivity measurement module (LWMM) 1 could not be found.
The control unit does not detect the conductivity measuring module 1. The cause is often a...
1. Unplug the device. 2. Locate the LWMM 1 module. 3. Carefully inspect its connector and...
The device reports that frequency converter/drive (FU/SA) 10 is not detected.
Loss of communication between the main control board and the frequency converter 10. This...
1. Turn off the device. 2. Access the FU/SA 10 frequency converter. 3. Check all power and...
Error message indicating a fault on the electronic load cell (EWZ) 010 1 (static signal).
Load cell 1 of module 010 provides an incorrect or out-of-range static signal, indicating a...
1. Turn off the power to the machine. 2. Locate the EWZ 010 1 load cell. 3. Check its...
The device signals a fault on the electronic weighing cell (EWZ) 010 2 (static signal).
Load cell number 2 of module 010 is faulty or sending an invalid static signal to the...
1. Perform a safe power off of the device. 2. Identify the EWZ 010 2 load cell. 3. Examine...
Electronic load cell (EWZ) error 010 1, indicating a dynamic signal problem.
The dynamic signal from load cell 1 is inconsistent or absent, suggesting a problem with...
1. Unplug the device from the mains. 2. Access the EWZ 010 1 load cell. 3. Check the...
A dynamic signal fault is reported for electronic load cell (EWZ) 010 2.
Load cell 2 sends erroneous dynamic data or no data during operation, indicating an...
1. Turn off the device. 2. Locate the EWZ 010 2 load cell. 3. Inspect its connectors and...
The device displays an error indicating that input module (EM) 10 1 cannot be found.
The central control unit is unable to communicate with input module number 1 in group 10....
1. Turn off the power supply. 2. Locate the EM 10 1 input module on the technical diagram....
An error message indicates that the input module (EM) 10 2 is not detected.
Loss of communication between the control unit and input module 2 of group 10. The module...
1. Unplug the device for any intervention. 2. Locate the EM 10 2 input module. 3. Make sure...
The device indicates that measuring module (MM) 10 is not found.
The main processor does not detect the measurement module 10 on the communication bus. This...
1. Turn off the machine. 2. Identify the location of the MM 10 measurement module. 3. Check...
Error message indicating that output module (AGM) 10 1 is not detected by the system.
The control unit is unable to communicate with output module 1 of group 10. The module may...
1. Turn off the power to the device. 2. Locate the AGM 10 1 output module. 3. Check that...
An error is displayed indicating that the output module (AGM) 10 2 could not be found.
Communication problem between motherboard and output module 2 of group 10, possibly due to...
1. Unplug the device from the power source. 2. Locate the AGM 10 2 module. 3. Disconnect...
The device reports that Serial Interface Module (SSM) 10 1 is not detected.
The control unit cannot communicate with serial interface module 1 in group 10. This may be...
1. Turn off the device. 2. Find the location of the SSM 10 1 module. 3. Check its...
Error displayed indicating that Serial Interface Module (SSM) 10 2 could not be found.
Loss of communication link between the processor and serial interface module 2 of group 10.
1. Turn off the power supply for safety reasons. 2. Locate the SSM 10 2 module. 3. Inspect...
The device displays a critical message “CPU 10 Failure” and asks you to call technical service. The device is unusable.
Major processor (CPU) hardware failure on module 10 control board.
1. Attempt a complete reset by unplugging the device for several minutes. 2. If the error...
The device indicates that spray arm control is not available and refuses to start the program.
The spray arm rotation monitoring system is defective or disabled. The rotation sensor,...
1. Make sure the spray arms are not blocked and can rotate freely. 2. Check that the...
The device reports that the conductivity measurement is unavailable and prevents the program from starting.
The conductivity (turbidity) sensor is defective, disconnected or its electrodes are dirty,...
1. Turn off the power. 2. Locate the conductivity sensor in the pump housing. 3. Check the...
The device indicates that the barcode reader is not available and the program cannot be run.
The barcode reader is disconnected, its cable is damaged, or the reader itself is defective.
1. Verify that the barcode scanner is properly connected to its port. 2. Examine the drive...
The device displays a message asking to regenerate the water softener. Washing results may be poor.
The water softener has reached capacity and needs a regeneration cycle with regenerating salt.
1. Open the softener salt tank. 2. Completely fill the tank with specific regenerating...
The device displays an unknown error number or a message saying "Unknown error number."
The electronics have recorded an unlisted error condition, possibly a software error (bug)...
1. Attempt a complete reset by unplugging the device from the mains for 15 minutes. 2. Plug...
No error codes displayed, normal operation. Visible only in service mode.
There are no active or logged errors in the system fault log.
This code confirms the absence of a fault. No intervention is necessary. If you experience...
No error codes displayed, normal operation. Visible only in service mode.
There are no active or logged errors in the system fault log.
This code confirms the absence of a fault. No intervention is necessary. If you experience...
The device detects water in the tank when it should be empty, for example before the start of a cycle.
The drain pump is blocked/faulty, the drain hose is clogged, or the water inlet solenoid...
1. Check the drain hose for kinks or obstructions. 2. Clean the drain pump filter. 3. Check...
The device detects water in the tank when it should be empty, for example before the start of a cycle.
The drain pump is blocked/faulty, the drain hose is clogged, or the water inlet solenoid...
1. Check the drain hose for kinks or obstructions. 2. Clean the drain pump filter. 3. Check...
The appliance door remains locked after the end of a cycle, sometimes with a drum movement message.
The rotation sensor detects a false movement of the drum, or the door locking system is...
1. Wait several minutes for the system to stabilize. 2. Unplug the device for 5 minutes to...
The appliance door remains locked after the end of a cycle, sometimes with a drum movement message.
The rotation sensor detects a false movement of the drum, or the door locking system is...
1. Wait several minutes for the system to stabilize. 2. Unplug the device for 5 minutes to...
Our official certified partners service Miele appliances in your area.