Access our premium database of error codes, common faults, and professional repair solutions for Miele appliances.
The coffee machine does not produce steam or hot water when these functions are selected.
The thermoblock intended for steam production is electrically faulty, either by cutting its...
Turn off the power. Locate the steam thermoblock and test the continuity of its thermal...
Miele F82: Operational cycle fault detected during Built-in Oven program execution.
Operational sensor variance, wiring connector discontinuity, or component parameter...
1. Disconnect 230V mains power for 3 minutes. 2. Inspect wire harness and edge connectors...
The coffee machine stops during the heating phase or produces an excessive amount of steam from the coffee outlet.
The temperature regulation of the water thermoblock is faulty. The cause is either a faulty...
Unplug the device. Test the ohmic value of the NTC probe at room temperature. If the probe...
Miele F83: Operational cycle fault detected during Built-in Oven program execution.
Operational sensor variance, wiring connector discontinuity, or component parameter...
1. Disconnect 230V mains power for 3 minutes. 2. Inspect wire harness and edge connectors...
The device reports an overheating error specifically when using the steam function.
The steam thermoblock temperature control system is out of service, due to a faulty...
Disconnect the machine from the electrical network. Measure the resistance of the NTC probe...
Miele F84: Operational cycle fault detected during Dishwasher program execution.
The slide shutter on the circulation pump, which helps divert water, is stuck or faulty.
This requires a service technician to inspect and potentially replace the circulation pump...
The dishwasher has a water filling fault, the cycle does not start or stops at the start.
The water distributor at the inlet of the side filler fails to position itself, due to a...
Turn off the power. Remove the side panel to access the filler. Inspect the small...
Miele F85: Operational cycle fault detected during Dishwasher program execution.
Similar to F84, this indicates a fault with the slide shutter system on the circulation pump.
A service technician is required to diagnose the circulation pump and its components.
The dishwasher stops and displays an error, while the water distributor may make repeated clicking sounds.
The electronic board receives inconsistent and constantly changing positioning signals from...
After unplugging the unit, inspect the wiring connecting the water splitter to the...
The dishwasher reports a problem with the salt container, even if it is correctly filled and closed.
The magnetic sensor (Reed switch) which detects the presence of the salt pot lid has failed...
Unplug the machine. Check that the salt pot cap is the original one and that its magnet is...
The washing results are poor, with whitish deposits on the dishes, and an error code is displayed.
One of the sensors built into the water softener (brine level, hardness) is transmitting...
Turn off the power. Make sure the salt pot contains salt and water. Check the sensor...
The automatic dishwasher cycles have an inappropriate duration (too long or too short) in relation to the degree of soiling.
The optical turbidity sensor, which measures dirt in the water, is either dirty or...
Unplug the device. Locate the turbidity sensor in the tank bowl. Clean its lens carefully....
The device refuses to start or interrupts its cycle by displaying a critical error linked to an internal process.
The oxygen (O2) sensor, used for advanced functions (hygiene, etc.), provides values...
Turn off the power. Locate the O2 sensor. Check the cleanliness of the probe and the...
The device interrupts the current cycle and displays code F90, indicating a problem with the oxygen measuring system.
The oxygen sensor (Lambda or O2 probe) is defective or its communication with the...
Carry out a reset by unplugging the device from the mains for several minutes. If the error...
The washing machine does not appear to adapt cycle length or water consumption to the amount of laundry, potentially displaying code F91.
The load detection system, which weighs the laundry to optimize the cycle, is inoperative....
Consult the user manual to run a calibration program if available. Make sure the device is...
An F92 warning message is displayed, indicating a potential risk of microbial growth inside the device.
This code is a preventive alert indicating that internal conditions (humidity, temperature,...
Immediately run a high temperature maintenance cycle (e.g. 'Machine Clean' program or 90°C...
Some device functions are inactive (e.g. heater or motor does not start) and code F93 is displayed.
The auxiliary relay electronic board, which controls power to several components, is...
Turn off the device. Visually inspect the relay board for signs of damage (burnt...
The device does not fill or fills very slowly when connected directly to a water supply.
The water supply is blocked. Common causes are a closed tap, a kinked inlet pipe, a clogged...
Check that the water tap is fully open and the hose is not pinched. Unscrew the hose on the...
The device stops by signaling that the water tank (for example, the condensation tray) is full, even though it is empty or lightly filled.
The tank water level sensor is stuck in the high position, dirty or electrically faulty,...
Remove and empty the tank. Clean it carefully, as well as the sensor housing and the float...
The device cannot be filled from an alternative water source (internal tank, rainwater).
The non-conventional water suction system is broken. This may be due to an empty source...
Make sure the alternative water source is sufficiently filled. Inspect and clean the...
Steam generation system fault
Issue with the steam generator, water supply to the steam system, or a blockage in the...
Ensure the water container is full and correctly inserted. Run the descaling program. If...
Miele F97: Operational cycle fault detected during Induction Hob program execution.
Operational sensor variance, wiring connector discontinuity, or component parameter...
1. Disconnect 230V mains power for 3 minutes. 2. Inspect wire harness and edge connectors...
A maintenance message F97 appears on the screen of a gas appliance (tumble dryer), indicating preventive wear of a component.
The gas burner ignition unit has reached the number of operating cycles estimated by the...
The appliance may continue to operate temporarily, but it is imperative to contact an...
The gas dryer attempts to start heating but stops after several unsuccessful attempts to ignite the flame.
Lack of gas ignition due to a closed gas inlet valve, a faulty gas solenoid valve, an...
Check that the gas supply to the appliance is turned on. Observe the igniter when starting;...
The device is completely unusable and displays code F99, indicating a general lockout.
This code signals a major software hang, which can be triggered by a series of unresolved...
Attempt a full reset by unplugging the device from the mains for at least 30 minutes. If...
The device displays error F100 and does not work or exhibits abnormal behavior, related to internal communication.
Communication between the main electronics board and a specific control module (identified...
Unplug the appliance electrically. Access the electronic boards and meticulously check the...
The device displays error F100 and does not work or exhibits abnormal behavior, related to internal communication.
Communication between the main electronics board and a specific control module (identified...
Unplug the appliance electrically. Access the electronic boards and meticulously check the...
Error code F101 appears at startup or during operation, indicating a specific hardware problem.
The IK6 electronic module is identified by the system as defective or not compatible. This...
Check the part number of the installed IK6 module to confirm compatibility with the exact...
Error code F101 appears at startup or during operation, indicating a specific hardware problem.
The IK6 electronic module is identified by the system as defective or not compatible. This...
Check the part number of the installed IK6 module to confirm compatibility with the exact...
Communication error between modules
Communication has been lost between the main electronic module and another module (e.g.,...
Turn the appliance off and on again. If the fault reoccurs, a technician is needed to check...
Our official certified partners service Miele appliances in your area.