Scholtès Dynamic Air Cooling & Total No-Frost Built-in Refrigerator: Diagnostic fault code A1 registered by the microcomputer controller. Freezer compartment high temperature warning (> -9°C)
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Dynamic Air Cooling & Total No-Frost Built-in Refrigerator: Diagnostic fault code A2 registered by the microcomputer controller. Refrigerator compartment high temperature warning (> +10°C)
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès LTE / LPE Maxi Plate 14-Place Integrated Dishwasher: Diagnostic fault code A04 registered by the microcomputer controller. Wash water temperature sensor NTC open or short circuit
Scholtès LTE / LPE Maxi Plate 14-Place Integrated Dishwasher: Diagnostic fault code A06 registered by the microcomputer controller. Water fill timeout / flowmeter pulses missing or tap closed
Scholtès LTE / LPE Maxi Plate 14-Place Integrated Dishwasher: Diagnostic fault code A12 registered by the microcomputer controller. Communication loss between user interface and main board
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Alarm code AL04 indicates prolonged AC mains power outage; internal cabinet temperature rose above safe food storage threshold.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Status code CC indicates continuous cooling or fast freeze mode has run continuously for over 24 hours without cycling off.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code CI indicates ice maker harvest arm motor stalled; ejector blades jammed against ice cubes in mold.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Status notification dF indicates defrost cycle in progress; compressor and fan paused while calrod heater operates.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code E1 registered by the microcomputer controller. Touch key panel obstructed / liquid spill or object over controls
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code E5 registered by the microcomputer controller. Internal communication loss between touch UI and power generator module
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code E6 registered by the microcomputer controller. Power module heatsink temperature sensor over-temperature (>95°C)
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code E7 registered by the microcomputer controller. Induction coil temperature sensor NTC open or short circuit
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code E9 registered by the microcomputer controller. User interface touch configuration checksum error
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code E9 indicates critical high temperature condition inside cabinet; perishable food at risk of spoiling.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic error ER CF indicates condenser cooling fan motor stall or feedback signal loss; compressor overheating danger.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code ER dS indicates defrost NTC thermistor open or short circuit; defrost cycle duration strictly time-limited.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code ER FF indicates freezer evaporator fan motor stalled or drawing excessive current; freezing performance lost.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code ER rF indicates fresh food compartment circulating fan motor stall; poor temperature distribution in refrigerator.
Scholtès Heat Pump Sensor Dry Tumble Dryer: Drum drive motor relay or triac failure F01; power PCB detects uncommanded drum rotation or shorted motor driver.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code F01 registered by the microcomputer controller. Induction generator left rear zone IGBT driver fault
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F01 indicates fresh food compartment evaporator NTC sensor out of calibration or open circuit.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F01 registered by the microcomputer controller. Motor triac short-circuit / motor runaway protection
Scholtès Dynamic Air Cooling & Total No-Frost Built-in Refrigerator: Diagnostic fault code F1 registered by the microcomputer controller. Refrigerator compartment air temperature NTC sensor failure
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code F02 registered by the microcomputer controller. Induction generator left front zone IGBT driver fault
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F02 indicates freezer evaporator NTC sensor out of calibration or short-circuit detected.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F02 registered by the microcomputer controller. Motor tachometer generator open / no pulses received
Scholtès Heat Pump Sensor Dry Tumble Dryer: Front air duct NTC thermistor fault F03; process air temperature sensor signal detected open or shorted to chassis.
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code F03 registered by the microcomputer controller. Induction generator right rear zone IGBT driver fault
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F03 registered by the microcomputer controller. Wash water temperature NTC sensor open or short circuit
Scholtès Dynamic Air Cooling & Total No-Frost Built-in Refrigerator: Diagnostic fault code F3 registered by the microcomputer controller. Freezer compartment air temperature NTC sensor failure
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code F04 registered by the microcomputer controller. Induction generator right front zone IGBT driver fault
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F04 indicates motorized air damper position sensor feedback switch open or shorted.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F04 registered by the microcomputer controller. Water level pressure switch stuck on empty state
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code F05 registered by the microcomputer controller. Induction coil NTC thermistor disconnected or open circuit
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F05 indicates defrost heater circuit open circuit; defrost cycle aborted due to zero current draw.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F05 registered by the microcomputer controller. Drain pump blocked or pressure switch stuck on full state
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Scholtès Dynamic Air Cooling & Total No-Frost Built-in Refrigerator: Diagnostic fault code F5 registered by the microcomputer controller. Ambient room temperature NTC sensor failure
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code F06 registered by the microcomputer controller. Induction coil NTC thermistor shorted to chassis or ground
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F06 registered by the microcomputer controller. Program selector switch position contact defect
Scholtès Galileo / Multi-Oven / S-Line Pyrolytic Built-in Oven: Diagnostic fault code F07 registered by the microcomputer controller. Tangential cooling fan motor open or Hall tachometer failure (<700 RPM)
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F07 indicates evaporator fan Hall-effect speed feedback pulse missing; fan runs in fail-safe mode.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F07 registered by the microcomputer controller. Wash heating element relay open or heater element open circuit (~26 Ω)
Scholtès Dynamic Air Cooling & Total No-Frost Built-in Refrigerator: Diagnostic fault code F7 registered by the microcomputer controller. Evaporator defrost heating element open circuit or thermal fuse blown
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Heat Pump Sensor Dry Tumble Dryer: Heating element open circuit or heat pump compressor failure F08; air chamber temperature fails to rise by 5°C in 15 minutes.
Immersion / Air Heating Element & Klixon Thermostat
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code F08 registered by the microcomputer controller. Auxiliary DC power supply rail out of tolerance (+5V/+12V rail drop)
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F08 indicates condenser cooling fan motor circuit open or stalled; high condensing pressure and compressor thermal tripping.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Galileo / Multi-Oven / S-Line Pyrolytic Built-in Oven: Diagnostic fault code F09 registered by the microcomputer controller. Communication loss between user display board and power PCB
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F09 indicates user interface (UI) display board communication timeout; control panel keys fail to respond.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F09 registered by the microcomputer controller. Main control board EEPROM setup checksum failure
Scholtès Dynamic Air Cooling & Total No-Frost Built-in Refrigerator: Diagnostic fault code F9 registered by the microcomputer controller. Motorized air damper flap position sensor failure / flap stuck
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès TFT Touch Screen Multi-Zone Pyrolytic Oven: Electronic range control (ERC) EEPROM checksum fault F1 E0; oven display beeps continuously and disables all bake modes.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Dynamic Air Cooling & Total No-Frost Built-in Refrigerator: Diagnostic fault code F10 registered by the microcomputer controller. Variable speed inverter compressor communication error
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F10 registered by the microcomputer controller. Pressure switch signal simultaneous empty and full (inconsistent)
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Scholtès Supreme Inox & Touch-Control Dishwasher: Main electronic control board relay malfunction F1 E1; dishwasher fails to execute wash cycles and beeps on power-up.
Scholtès TFT Touch Screen Multi-Zone Pyrolytic Oven: Relay board microprocessor communication failure F1 E1; oven elements fail to energize and error tones sound.
Scholtès Heat Pump Sensor Dry Tumble Dryer: UI to main control board serial communication timeout F11; console display fails to synchronize packets with power board.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Dynamic Air Cooling & Total No-Frost Built-in Refrigerator: Diagnostic fault code F11 registered by the microcomputer controller. Freezer evaporator brushless DC fan motor stalled / no tacho
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F1E1 indicates main electronic control board MCU microprocessor failure; internal relays fail to engage.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code F12 registered by the microcomputer controller. User interface EEPROM data mismatch with power stage
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F12 registered by the microcomputer controller. Display board communication loss with main control board
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F13 registered by the microcomputer controller. Dryer NTC sensor open or short circuit (Washer-Dryer)
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F14 registered by the microcomputer controller. Dryer heating element open circuit (Washer-Dryer)
Scholtès Heat Pump Sensor Dry Tumble Dryer: Drum belt tensioner safety switch open F15; microswitch on motor jockey arm trips due to loose or broken drive belt.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code F17 registered by the microcomputer controller. Door interlock delayed locking / PTC microswitch open
Scholtès TFT Touch Screen Multi-Zone Pyrolytic Oven: Shorted keypad touch pad switch F2 E0; oven control registers a continuously depressed key and locks out panel.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Heat Pump Sensor Dry Tumble Dryer: Display to power module serial handshake loss F21; communication line fails periodic liveness heartbeat check.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F2E1 indicates communication loss between user interface display panel and main control board.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Supreme Inox & Touch-Control Dishwasher: User interface to electronic control board communication loss F2 E2; console display goes dark or flashes intermittently.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F2E2 registers user interface supply voltage abnormal; dispenser screen flickers or resets erratically.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Dynamic Air Cooling & Total No-Frost Built-in Refrigerator: Diagnostic fault code F28 registered by the microcomputer controller. User interface display communication timeout with power board
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Supreme Inox & Touch-Control Dishwasher: Thermistor NTC water temperature sensor fault F3 E1; wash cycle runs excessively long or water fails to reach sanitize temp.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F3E1 indicates fresh food compartment (RC) NTC thermistor open or short circuit; cabinet temperature fluctuates wildly.
Scholtès Supreme Inox & Touch-Control Dishwasher: Wash water heating fault F3 E3; control board detects no temperature rise after 30 minutes of continuous wash operation.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F3E5 indicates freezer evaporator defrost thermistor open or out of limits; defrost heater fails to terminate correctly.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F4E1 indicates fresh food compartment evaporator fan motor stalled or disconnected; air circulation fails.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Supreme Inox & Touch-Control Dishwasher: Circulation wash motor drive triac fault F4 E2; wash pump motor fails to start or runs uncommanded at full speed.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F4E2 indicates freezer evaporator fan motor stall or tachometer feedback failure; freezer warms rapidly.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F4E4 indicates in-door ice box blower fan motor blocked or disconnected; ice melting in storage bin.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code F47 registered by the microcomputer controller. LIN-bus communication error between touch display and power module
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code F48 registered by the microcomputer controller. Induction zone booster power limiter jumper missing or invalid
Immersion / Air Heating Element & Klixon Thermostat
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code F49 registered by the microcomputer controller. Capacitive touch controller I2C communication bus error
Immersion / Air Heating Element & Klixon Thermostat
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F5E1 indicates French door interlock switch or vertical mullion heater open; condensation forms on cabinet flange.
Immersion / Air Heating Element & Klixon Thermostat
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F5E2 indicates dispenser ice chute motorized flapper door failed to open or close; air leaks frost the chute.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F5E3 indicates motorized air damper door stuck open or closed; fresh food section either freezes or warms up.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F6E1 indicates serial communication timeout between main control board and door dispenser display.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F6E2 indicates communication loss between main power board and variable frequency inverter compressor driver.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F8E1 indicates primary water inlet solenoid valve electrical fault; water dispenser and ice maker starved of water.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code F8E2 indicates ice maker fill valve flow meter timeout; insufficient water volume dosed into ice tray.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Status notification FB indicates water filter bypass plug is installed; water dispenser operating without active carbon filtration.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code H1 indicates critical over-temperature condition in freezer; compartment temperature rose above 0°C.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code H2 indicates fresh food compartment temperature elevated above +16°C; loss of refrigeration cooling capacity.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès MLXE / SLW Supreme Care Integrated Washer-Dryer: Diagnostic fault code H20 registered by the microcomputer controller. Water filling timeout / inlet valve or tap pressure failure
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code HC indicates high cabinet temperature warning; freezer compartment exceeded -5°C for longer than 60 minutes.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code L registered by the microcomputer controller. Child lock safety active / controls locked
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code LC indicates low temperature condition in fresh food compartment; fresh vegetables freezing on bottom crisper shelves.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Status notification OF indicates cooling off or showroom demo mode is active; display operates but cooling system is shut down.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code OV indicates inverter driver DC link over-voltage trip; compressor shut down to protect power semiconductors.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code P1 indicates delicatessen pantry drawer temperature sensor circuit open or shorted.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code PF indicates power failure event occurred; electronic control board clock reset and alarm flashes.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code SY CE indicates system communication error between user interface touch panel and main control board.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code SY EF indicates system evaporator fan circuit malfunction; zero rotational feedback detected by electronic control.
Compressor Motor Windings (Run/Start) & Defrost Heater
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code U400 registered by the microcomputer controller. Voltage connection fault (400V 2-phase connected across single 230V rail)
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code 7E indicates external ambient temperature sensor analog channel error; control defaults to 22°C nominal room reference.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Status notification OF indicates cooling off or showroom demo mode is active; display operates but cooling system is shut down.
On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Demo mode inadvertently triggered by key combination sequence during door cleaning or initial installation.
Open refrigerator door. Press and hold Freezer Temperature and Fast Freeze buttons simultaneously for 5 seconds until beep sounds and display returns to normal. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code OV indicates inverter driver DC link over-voltage trip; compressor shut down to protect power semiconductors.
On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Mains surge exceeding 265V AC, regenerative braking energy backfeed, or degraded DC filter electrolytic capacitor on inverter board.
Disconnect power. Measure incoming mains voltage (nominal 230V AC ±10%). Test DC bus capacitor voltage with DMM (normal 310–330V DC, trip > 420V DC). Replace inverter PCB if voltage is normal. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code P1 indicates delicatessen pantry drawer temperature sensor circuit open or shorted.
On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Severed sensor harness during drawer removal, moisture ingress in probe connector, or failed NTC bead (nominal 2.7 kΩ at 25°C).
Disconnect power. Remove pantry drawer and unclip sensor cover. Measure sensor resistance (2.7 kΩ at 25°C). Inspect wiring harness pin contacts. Replace pantry thermistor if open. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization.
Electronic Control Board (PCB) & Bus Communications
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code PF indicates power failure event occurred; electronic control board clock reset and alarm flashes.
On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Grid power blackout, brownout voltage drop below 180V AC, or tripped household circuit breaker.
Verify line voltage (230V AC ±10%). Press Cancel/Confirm button to clear PF alert. Check internal temperatures of freezer and fresh food compartments. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization.
Scholtès Galileo / Multi-Oven / S-Line Pyrolytic Built-in Oven: Diagnostic fault code STOP registered by the microcomputer controller. Oven cycle finished or thermal safety shut-off engaged
On Scholtès appliances engineered with Galileo electronic architecture with high-density pyrolytic thermal barrier, PT500 probe feedback, Hall-effect cooling fan regulation, and bi-metallic motorized door latch: cooking cycle terminated or thermal trip Metrological tolerance verification: nominal PT1000 platinum RTD sensor 1080 Ω at 20°C (1000 Ω at 0°C).
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: measure probe resistance across harness terminals (expected ~1080 Ω at 20°C). Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Turn temperature and function dials to 0. Switch off oven circuit breaker for 60 seconds. Restore power, touch and hold the Timer/Clock button for 4 seconds until '0:00' flashes and error code extinguishes.
Electronic Control Board (PCB) & Bus Communications
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code SY CE indicates system communication error between user interface touch panel and main control board.
On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Crushed communication wiring in upper door hinge, loose terminal connector, or burned RS-485/UART transceiver chip on main PCB.
Disconnect power. Inspect hinge harness for broken wires. Test 12.0V DC supply and serial transmit/receive pulses (0.5–4.5V DC). Repair harness or replace main board. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code SY EF indicates system evaporator fan circuit malfunction; zero rotational feedback detected by electronic control.
On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Fan blade seized by frost buildup, open BLDC motor winding (15–35 Ω), disconnected 3-pin fan plug, or blown drive triac on main PCB.
Disconnect power. Remove rear freezer grille. Clear ice from fan shroud. Measure 12.0V DC between pins 1 and 2, and test tachometer pulse on pin 3. Replace motor if open circuit. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization.
Electronic Control Board (PCB) & Bus Communications
Scholtès Induction Touch Control & S-Line Direct Slider Cooktop: Diagnostic fault code U400 registered by the microcomputer controller. Voltage connection fault (400V 2-phase connected across single 230V rail)
On Scholtès appliances engineered with Arcadia / E.G.O. high-frequency induction power modules with digital temperature monitoring across each inductor core, touch slider filtering, and dynamic phase balancing: neutral conductor connected to second live phase Metrological tolerance verification: voltage > 380V AC measured across terminals..
Disconnect mains power before servicing. Unplug the harness at the main PCB and use a calibrated digital multimeter: disconnect power immediately and correct mains wiring at terminal block. Inspect contacts for pin oxidation or loose terminals. Replace defective part if out of tolerance, re-energize and clear error: Ensure all cookware is removed and glass is completely dry. Turn off mains isolator switch for 90 seconds. Restore power and press the On/Off sensor firmly for 4 seconds until the hob performs self-calibration and beeps.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code UV indicates inverter driver DC link under-voltage trip; compressor cannot maintain required torque.
On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Grid brownout drop below 180V AC, high-resistance wall outlet plug, or dried-out electrolytic reservoir capacitors (< 210V DC bus).
Verify line voltage under compressor startup load (min 207V AC). Check DC bus voltage on inverter board (trip occurs below 210V DC). Replace inverter board if supply is 230V AC. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code 6E indicates defrost temperature sensor circuit resistance drift outside valid electronic window (2.0–25.0 kΩ).
On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Thermal shock degradation of NTC ceramic wafer, cracked epoxy sealant, or partial moisture short circuit across sensor pins.
Disconnect power. Unclip defrost sensor from evaporator coil. Measure resistance in ice water bath (7.9 kΩ at 0°C, 2.7 kΩ at 25°C). Replace sensor assembly if drift exceeds ±5%. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code 7E indicates external ambient temperature sensor analog channel error; control defaults to 22°C nominal room reference.
On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Sensor wire pinch inside top door hinge plastic shroud, open NTC thermistor element, or failed ADC input pin on main PCB.
Disconnect power. Remove top hinge cover. Test ambient sensor resistance (nominal 2.7 kΩ at 25°C). If open circuit, replace ambient sensor harness. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization.
Scholtès Pure Cold Built-in Total NoFrost Refrigerator: Diagnostic code 8E indicates ice maker mold temperature thermistor circuit error; automatic ice harvest cycle suspended.
On Scholtès refrigerators (Scholtès Haute Horlogerie Culinaire sensors and micro-electronic platform architecture): Water seepage into mold thermistor cavity, cracked wire pigtail, or open NTC element (nominal 2.7 kΩ at 25°C, 14.5 kΩ at -10°C).
Disconnect power. Remove ice maker assembly. Measure mold thermistor resistance across pins (14.5 kΩ at -10°C). If open circuit, replace ice maker module. Press and hold Alarm Reset pad for 5 seconds, verify compartment display stops blinking, and allow 12h for complete stabilization.