Access our premium database of error codes, common faults, and professional repair solutions for Miele appliances.
An error message indicates that the external dosing container 9 is empty, preventing the program from starting or continuing.
The detergent or rinse aid in the external container 9 is used up, or the level sensor is...
Fill the external dosing container 9. If the problem is not resolved, contact technical...
The screen displays a general fill request for an unspecified external dosing tank.
One or more of the connected external dosing tanks are empty, triggering a generic alert.
Check the level of all external dosing tanks connected to the device and fill any that are...
The device displays a message asking to contact after-sales service, with a telephone number.
An unspecified critical error has occurred, requiring the intervention of a qualified...
Note the full error code displayed. Turn off and unplug the device for a few minutes, then...
A fault is reported in the time measurement by the Profitronic control system.
Internal problem with the electronic board clock or timer, potentially due to a power surge...
Perform a reset of the device by unplugging it from the mains for 10 minutes. If the fault...
The device stops and reports excessively high water temperature, as a safety measure.
The water temperature sensor (NTC probe) is faulty, or the heater relay is stuck in the...
Unplug the device. Check the temperature probe connection. Test the resistance of the...
The device interrupts its cycle, often drying, due to the air temperature being too high.
The air temperature sensor is defective, the ventilation system is obstructed, or the...
Make sure filters and air ducts are not blocked. Check fan operation. Test the air...
The device reports a general fault linked to the wash arm module.
Communication or power supply problem with the module that controls the washing arms...
Reset the device by turning off the power. Check the wiring and connectors leading to the...
A problem is detected with the upper wash arm of the machine, affecting the cleaning quality.
The upper spray arm is blocked, its nozzles are clogged, or the rotation sensor does not...
Make sure the upper wash arm can rotate freely. Clean the arm nozzles. If the error...
The device reports a malfunction specific to spray arm number 5.
The wash arm 5 is obstructed, mechanically blocked, or its rotation detection system is broken.
Check that the wash arm 5 rotates without hindrance. Clean the spray holes. Examine the...
An error is displayed regarding wash arm number 4, indicating abnormal rotation.
The rotation of the wash arm 4 is not detected, probably due to a mechanical blockage or a...
Check the freedom of movement of the wash arm 4. Unblock its nozzles if necessary. An...
The device indicates a fault on wash arm number 3, which may result in uneven washing.
Wash arm 3 does not rotate correctly or its rotation is not registered by the control system.
Clear any obstruction preventing rotation of the arm 3. Clean the nozzles thoroughly. If...
An error message points to a problem with spray arm number 2.
Physical blockage, clogged nozzles or rotation sensor failure for wash arm 2.
Make sure that the wash arm 2 can rotate without constraint. Clean the water jets. If the...
The dishwasher reports an anomaly on wash arm number 1.
The washing arm 1 is blocked by a utensil, or its water outlet holes are blocked,...
Check that no object is obstructing the rotation of the arm 1. Completely clean the...
A malfunction is detected in the lower wash arm of the machine.
The lower spray arm is either blocked by an object or its nozzles are clogged, preventing...
Remove the lower basket and check the free rotation of the wash arm. Clean the spray holes...
The device signals an overflow level and the drain pump may activate continuously.
The anti-overflow system (safety pressure switch or float) has been activated, often due to...
Unplug the device. Check for a water leak in the retention pan. Tilt the device to drain...
The device displays an error related to water conductivity, affecting dosing or dirt detection.
The conductivity sensor is providing abnormal readings, or the water quality is out of...
Clean the conductivity sensor located in the tank. Be sure to use the recommended detergent...
The cycle is interrupted or extended with an error message linked to the cooling phase.
The device fails to lower the temperature within the allotted time, potentially due to a...
Check that the cold water inlet is correctly turned on and that the flow rate is...
A fault is detected on dosing system number 1, preventing the injection of the product.
Dosing pump 1 is blocked, the supply hose is pinched or blocked, or the pump is...
Check that the product tank is full. Inspect the dosing hose for any pinching or blockage....
The device reports an anomaly with dosing system number 2, the product is not distributed.
Malfunction of dosing pump 2, either by mechanical blockage, obstruction of the conduit, or...
Make sure product is present in the associated tank. Examine the dosing line. If the pump...
An error message indicates a problem with dosing system number 3.
Dosing pump 3 is not operating as expected, possibly due to an obstruction, empty hose, or...
Check the product level in the tank. Visually inspect the supply hose. If no abnormality is...
The control system reports a fault on dosing circuit number 4.
Dosing pump 4 is broken, its pipe is blocked, or there is a communication problem with the...
Fill the product tank if necessary. Check that the pipe is free. Perform a device reset. If...
The device asks to fill the specific 'OXIVARIO' tank.
The product level in the OXIVARIO tank (bleach or special additive) is too low.
Locate the OXIVARIO tank and fill it with the recommended Miele product. If the error...
A 'Dichtigkeit' (tightness) error is displayed, indicating a potential water leak and the device shutting down.
Water has been detected in the lower retention tank, activating the leak sensor (Aquastop)....
Unplug the appliance and turn off the water supply. Mop up the water in the retention tray....
A rotation or operating problem is detected on the upper wash arm.
The upper wash arm is obstructed by dishes, its nozzles are clogged with residue, or its...
Make sure the arm can rotate freely. Disassemble it and clean it under running water to...
The device reports a fault specific to spray arm number 5, affecting washing performance.
The rotation of arm 5 is not detected, often due to blockage by a utensil or obstruction of...
Check the rotation space of the wash arm 5. Clean its nozzles to ensure a correct water jet...
An operating error is reported for wash arm number 4.
Rotation of arm 4 prevented by an object, clogged nozzles reducing propulsion force, or...
Check and free the rotation space of the arm 4. Unblock the spray holes using a small...
The diagnostic system indicates a problem with spray arm number 3.
Arm 3 is blocked, not receiving enough water pressure to rotate (clogged nozzles), or the...
Inspect the arm 3 area for any obstructions. Disassemble and clean the arm nozzles. If the...
Washing is ineffective in a specific area of the tank and a wash arm 2 rotation alert is displayed.
The number 2 wash arm rotation sensor is not detecting any movement, possibly due to a...
Turn off the power. Access the wash arm 2. Check its freedom of manual rotation and ensure...
The device reports an anomaly on wash arm 1 and the cleaning results are disappointing.
The monitoring system did not register the rotation of the upper wash arm (1). The cause...
Unplug the appliance electrically. Pull out the upper basket to inspect the wash arm 1....
An error concerning the lower wash arm is reported, and food residue persists on the dishes in the lower basket.
The lower wash arm does not rotate correctly. The cause is often a large object blocking...
Turn off the power supply. Remove the lower basket. Make sure the lower spray arm can...
Our official certified partners service Miele appliances in your area.