Access our premium database of error codes, common faults, and professional repair solutions for Miele appliances.
Unable to select washing programs or the selected cycle does not start.
Wash program data is corrupted or inaccessible on the power board memory.
If possible, perform a factory reset via the service menu. Otherwise, intervention is...
Drying is ineffective, the dishes remain damp and the program may end prematurely.
The electronics detected an abnormal temperature difference between two points in the air...
Inspect the entire drying circuit, including the fan, ducts and filters, for obstructions....
The device reports an 'Error 1' fault from a connected external module, preventing normal operation.
The external communication module or connected device (e.g. dosing system) has sent a...
Consult the technical documentation of the external module to interpret the meaning of...
An 'Error 2' alert is displayed on the screen, related to an external device that is not functioning correctly.
A specific error condition, identified as '2', has occurred on a third-party device...
Diagnose the external device according to its manufacturer's instructions for error '2'....
Operation is interrupted by an 'Error 3' message referring to external equipment.
Connected equipment, such as a coin changer or management module, has reported an internal...
Identify the responsible external equipment. Refer to its user manual for troubleshooting...
Display of the code 'Error 4' relating to an external device, the cycle cannot continue.
The main device received an error signal '4' from a peripheral system, indicating an...
Isolate the problem by temporarily disconnecting the external device if possible. Consult...
An 'Error 5' code is generated by an external system, pausing or faulting the main unit.
Specific malfunction ('Error 5') detected on an additional module (eg: dosing pump, payment...
Follow the troubleshooting steps provided by the external module manufacturer for error...
The control panel displays 'Error 6' and indicates a problem with a connected accessory.
The accessory or device connected via the communications port has transmitted fault code '6'.
Completely turn off the Miele appliance and external accessory. Check the ports and...
The device stops and reports 'Error 7' linked to an external system.
A hardware or software failure, coded '7', is detected on a device connected to the system.
Perform diagnostics on the external device. Refer to its documentation for the meaning of...
'Error 8' alert message indicating an anomaly on an external component.
The external component interfaced with the device self-detected an internal error and...
Contact the customer service of the external component manufacturer, mentioning error code...
The cycle is blocked due to an 'Error 9' emitted by a connected device.
A trouble code '9' was sent by a peripheral system, indicating a critical problem requiring...
Reset the external device according to its standard procedure. If the problem persists,...
The device displays 'Error 10' and indicates a malfunction of an external module.
The external module reported a major fault, categorized as 'Error 10', to the Miele device.
It is imperative to consult the technical instructions of the external module to understand...
A custom error code or unusual message is displayed, set by an external control system.
A remote management system (e.g. home automation, building management) has sent a specific,...
Identify the external control system connected to the device. Review the configuration and...
The salt light is on or a 'Lack of salt' message is displayed, and white marks may appear on the dishes.
The regenerating salt tank of the integrated water softener is empty.
Open the salt reservoir cap located at the bottom of the tank. Using a funnel, fill the...
A message or light indicates 'Regeneration', the cycle may be longer than usual.
This is an informational message. The water softener must complete a regeneration cycle to...
No action is required from the user. Make sure the salt reservoir is sufficiently full. The...
The device is displaying a test code and is not in normal operating mode.
The device was unintentionally placed in diagnostic test mode, a procedure used at the...
Try to exit test mode by turning off the device using the on/off button, then unplugging it...
The program stops at the start of the cycle with a fault linked to filling, the device does not take in water.
An anomaly has been detected in the intermediate water tank filling system (pressure...
Contact technical service. A professional will need to inspect the entire water circuit,...
Product A dosage problem, the cycle is interrupted or the washing results are unsatisfactory.
The dosing monitoring system has identified a type 'A' fault, possibly a blocked dosing...
Check the product level in tank A. Inspect the dosing pump and corresponding hoses for...
The dishwasher reports a dosage fault 'Error B', affecting the quality of cleaning or rinsing.
A type 'B' error has been detected by dosing monitoring, often linked to a faulty flow or...
Check the sensor associated with dosing circuit B. Check that the chemical product used is...
An 'Error C' alert linked to the dosing system is displayed, and the corresponding product is not dispensed.
The monitoring system has detected a type 'C' anomaly, which may correspond to a lack of...
Make sure that tank C is full and that the suction pipe is well immersed in the product....
The device is faulty with an 'Error D' of the automatic dosing system.
Type 'D' fault generally indicates an electrical problem in the dosing circuit, such as an...
Turn off the device. Inspect metering pump wiring D. Measure pump resistance; if it is...
The cycle does not complete and a dosage monitoring 'Error E' is displayed.
Type 'E' error is often linked to an inconsistency in the dosing sensor data, indicating a...
Check the connection of the dosing circuit sensor E to the electronic card. Clean the...
The device displays a clear message requesting the filling of dosing tank 1.
The automatic dosing system level sensor has detected that product tank number 1 is empty...
Locate dosing tank 1 (internal or external). Fill it with the appropriate chemical. If the...
A visual or audible alert indicates that dosing tank 2 must be filled.
The supplies management system has determined that tank 2 requires refilling to continue...
Fill tank 2 following the manufacturer's instructions. Acknowledge the message on the...
A 'Fill DOS 3 tank' message prevents programs using this product from starting.
The liquid level in the third tank of the dosing system is insufficient.
Add the appropriate product to the dosing tank 3. Clean the level sensor contacts if...
The screen displays a notification to fill the dosing tank 4.
The tank 4 level sensor has signaled to the electronics that the product level is too low.
Fill the DOS 4 tank with the recommended consumable. Make sure there are no air bubbles or...
An alert asks the user to fill chemical tank number 5.
The volume of product in the dosing tank 5 has fallen below the critical threshold for...
Fill the tank 5. Inspect the suction pipe to ensure that it reaches the bottom of the tank....
The device displays a fill alert for external dosing tank number 6 and may interrupt the cycle.
The product level in the external dosing tank 6 is insufficient or the level sensor is...
Fill external dosing tank number 6 with the appropriate product. If the message persists,...
A notification requests the filling of external dosing container number 7 and the program is paused.
The external dosing container 7 is empty or the level detection system is not working properly.
Add the required detergent or additive to the DOS container 7. Restart the cycle. If the...
The device signals that external dosing tank number 8 needs to be filled, putting the cycle on hold.
The liquid level in the external dosing tank 8 is below the minimum threshold detected by...
Proceed to fill the DOS 8 tank. Make sure that the float or the level sensor is not blocked...
Our official certified partners service Miele appliances in your area.