Access our premium database of error codes, common faults, and professional repair solutions for Miele appliances.
The device does not detect the cart or basket, which prevents a program from starting.
A problem affects the cart recognition system (sensor, magnet, contactor) or the cart...
Check that the cart is correctly inserted and compatible with the device. Clean the...
An error specific to the TA valve (thermal disinfection) is displayed, blocking the cycles concerned.
Component fatigue, sensor feedback out of tolerance, wiring harness connector...
Unplug the appliance from the mains. Locate the TA valve and check its electrical...
The water flow in the thermal disinfection (TA) circuit is judged incorrect by the device, causing an interruption of the cycle.
The TA circuit flow meter is defective, scaled or clogged, or a blockage exists in the...
Turn off the appliance and close the water tap. Check the cleanliness of the water inlet...
The device signals an abnormal water level in the water heater (boiler), preventing heating or the program from running.
The pressure switch, the water level probe, or the boiler filling solenoid valve are defective.
Unplug the appliance. Make sure the water supply is functional and the pressure is...
An undocumented error code is displayed, without a clear description of the problem.
This code is generally unassigned or reserved for future use by the manufacturer. Its...
Perform a full reset of the device by unplugging it from the mains for at least 15 minutes....
A maintenance message indicates that the first operating hours counter has reached its limit.
The device has reached a predefined usage threshold requiring a specific preventive...
Consult the user manual to identify maintenance associated with this meter. Perform the...
A maintenance notification is displayed because the second operating hour counter has expired.
A component or system has reached its recommended lifespan, which triggers a scheduled...
Refer to the technical documentation for maintenance related to the 'Betriebszeit 2' meter....
The device displays a message explicitly requesting replacement of the fine filter.
The fine filter is clogged or has reached the end of its programmed life, which may...
Turn off the power. Follow the instructions in the manual to locate the fine filter...
An alert on the screen indicates that the coarse filter needs to be replaced or cleaned.
The main filter, called coarse, is clogged with debris or its recommended lifespan has been...
Turn off and unplug the device. Access the coarse filter, often located in the tank. Remove...
A scheduled maintenance message is displayed, linked to a specific operation counter (number 5).
The device has reached a predetermined service hours limit which requires special maintenance.
Identify the corresponding maintenance task in the device service manual. Perform...
A notification signals the end of a service interval, based on hour meter number 6.
The scheduled operating hours threshold for preventive maintenance has been reached.
Consult the technical documentation to determine the required maintenance action. After...
A general message such as 'Maintenance required' or a service icon appears on the screen.
A general maintenance interval, based on elapsed time or number of cycles, has been reached.
Carry out the standard periodic maintenance described in the manual (cleaning filters,...
Communication or operational error related to secondary computer number 1 of the Profitronic control system.
Hardware failure of auxiliary electronic card 1 or connection problem with the main card....
Perform a complete reboot of the device by turning off the power. If the error persists,...
A malfunction is reported in secondary computer number 2 of the Profitronic electronics.
Failure of the second auxiliary electronic card or loss of communication with the main...
Attempt a reset by unplugging the device. If the problem is not resolved, it is imperative...
An information message indicates that the critical process parameters (temperature, duration) have been successfully achieved.
This is not an error, but a confirmation of the correct execution of a validated cycle,...
No corrective action is required. This code is used for validation and traceability of the...
Critical alert: the parameters required for cycle validation (e.g. disinfection temperature) have not been reached.
Failure of a component (resistor, probe), water or electricity supply problem, or excessive...
Check basic supplies (water, electricity). Make sure the device is not overloaded. Run a...
A message indicates an incompatibility or software update regarding the Profitronic control system.
Component fatigue, sensor feedback out of tolerance, wiring harness connector...
This error requires the intervention of a Miele technician. He will have to ensure the...
An error is reported regarding the Profitronic system configuration settings, preventing operation.
Settings data stored in electronic board memory is corrupted, missing, or incorrect. 'KD'...
An authorized Miele technician must connect to the device with their diagnostic equipment...
Malfunction alert relating to the Profitronic control configuration parameters.
Similar to code F2091, this error indicates corruption or loss of essential operational...
Calling a Miele technical service is essential. The technician will need to diagnose the...
Wash programs are unavailable, corrupted, or an error is displayed when trying to select them.
Component fatigue, sensor feedback out of tolerance, wiring harness connector...
Only a Miele technician can resolve this problem. He will have to use his service interface...
An error occurs when accessing, saving or printing cycle protocols.
An issue affects the memory allocated for storing cycle logs. It may be full, corrupted or...
Try saving or deleting old protocols via the user menu, if the option is available. If the...
The device reports a problem with its own internal error log, preventing further failures from being logged.
The memory intended to store error codes is full, unreadable, or corrupt.
A Miele technician must log in to read and clear the error log. If the problem is hardware...
Cycle protocols do not print or a printer error message appears.
The printer is off, disconnected, out of paper/ink, or there is a communication problem...
Verify that the printer is turned on and properly connected. Make sure it contains paper...
The device, usually a three-phase model, does not start and displays an error related to the electrical connection.
The phase order of the three-phase power supply is incorrect, causing the motors to fail.
WARNING: Intervention reserved for a qualified electrician. Turn off the power at the...
A message asks to replace the battery. The device may lose its settings (time, date) after a power outage.
The backup battery on the electronic board, used to maintain the clock and some settings,...
Turn off the device. Locate the battery on the control board (often a button cell). Replace...
The program stopped because a load shedding signal (management of consumption peaks) lasted abnormally long.
The device is connected to an energy management system that has sent an extended load...
Check the operation of the building's energy management system. If no such system is used,...
The device signals that a power outage has occurred during the cycle and suggests resuming or canceling it.
An external power outage interrupted the operation of the device.
Check the general power supply and the circuit breaker dedicated to the device. Once power...
The program interrupts unexpectedly or the cycle temperature seems incorrect.
The drive motor temperature (TA) sensor is defective or its electrical connection is...
Turn off the device. Locate the temperature sensor on the engine block. Check the integrity...
The device displays an error at startup and refuses to launch a program; Custom settings can be reset.
A read or write error has occurred in the electronic card memory concerning the operating...
Perform a full reset by unplugging the device from the mains for at least 15 minutes. If...
The dishwasher is stuck on an error code and no longer responds to user commands.
Failed to save or recover general device parameters to non-volatile memory on the control...
Attempt a forced restart of the device by cutting off its power supply. If the problem is...
Our official certified partners service Miele appliances in your area.