Access our premium database of error codes, common faults, and professional repair solutions for Miele appliances.
An error is displayed, indicating a cold demineralized water (AD) supply fault.
The cold demineralized water circuit is closed, has insufficient flow, or its supply pipe...
1. Make sure the deionized water supply system is active and its valve is open. 2. Inspect...
The cycle is interrupted due to a problem with the hot demineralized water (AD) inlet.
The hot demineralized water supply is faulty: closed valve, choked pipe or clogged inlet...
1. Check that the hot demineralized water circuit valve is fully open. 2. Examine the...
The device signals a general fault on the demineralized water (AD) inlet and stops the program.
The main demineralized water supply is cut off, the pressure is too low, or a general...
1. Check the central demineralized water supply unit. 2. Check that the main valves are...
Drying is ineffective or the program stops, indicating an internal air heating problem.
The heating resistor for the internal air circuit is defective, its wiring is damaged, or a...
1. Turn off the power. 2. Technical intervention is required to measure the continuity of...
The device reports a failure of the external air heating system, affecting certain cycles.
The external air circuit heater resistor has failed, or there is a problem with its control...
1. Unplug the appliance from the electrical outlet. 2. Professional diagnosis is required...
The water in the tub remains cold, the washing results are poor and the cycle ends with an error.
The main heating element (immersion heater) is out of order, its power supply is faulty, or...
1. Turn off and unplug the device for any work. 2. A technician should measure the...
The device does not produce steam or water at very high temperature, indicating a boiler heating fault.
The boiler's heating resistance is defective, its safety thermostat has tripped, or its...
1. For safety reasons, turn off the power. 2. A professional must access the boiler to test...
Drying does not work and a general error related to air heating (TA) is displayed.
A fault has occurred on one of the elements of the air heating circuit or on a common...
1. Disconnect the machine electrically. 2. A complete diagnosis by a professional is...
The water pressure seems low, the spray arms malfunction and a water circulation error appears.
The circulation pump is blocked or broken, the high pressure switch (HDW) does not detect...
1. Turn off the power. 2. Remove and thoroughly clean all tank filters. 3. Make sure the...
The drying program stops abruptly displaying an indoor air overheating alert.
The internal temperature sensor is faulty, the circulation fan is blocked, or the air ducts...
1. Turn off, unplug the device and allow it to cool. 2. Check the cleanliness of lint...
The device interrupts its operation for safety reasons, signaling an excessive temperature in the external air circuit.
Poor ventilation around the machine, obstruction of the external ventilation grilles, or...
1. Make sure that the ventilation spaces around the device are respected. 2. Clean the air...
The water in the tank reaches an abnormally high temperature, triggering a safety shutdown of the program.
The heater relay is stuck in the active position or the water temperature sensor (NTC) is...
1. Unplug the appliance immediately to stop heating. 2. Let the water cool completely. 3....
The device stops and reports an excessive temperature in the boiler.
Malfunction of the boiler temperature control system, such as a faulty thermostat or a...
1. Turn off the device and unplug it from the mains. 2. Do not attempt to restart it. 3....
Miele F2057: NTC temperature sensor signal out of range (open or short circuit) in Oven / Microwave.
Generalized obstruction of the air circuit (filters, condenser), or failure of a...
1. Stop, unplug the appliance and allow it to cool. 2. Carry out a complete cleaning of all...
The unit displays an error specific to the outdoor air temperature sensor, affecting drying performance.
The outside air temperature sensor (NTC sensor) is short-circuited or open-circuited, or...
1. Unplug the appliance. 2. Technical intervention is required to locate the sensor. 3. The...
Drying is poor (too long or damp laundry) and an internal air sensor error code appears.
The drying air temperature sensor is out of order or its connectors are oxidized or...
1. Turn off the power. 2. Since the sensor is located in the hot air duct, a technician...
Water temperature is poorly regulated (too hot or not hot enough), resulting in ineffective washing or sensor error.
The tank temperature sensor (CTN) is defective, covered with scale, or its wiring is damaged.
1. Disconnect the device from the power supply. 2. A technician will locate the probe,...
The boiler temperature regulation is faulty, causing steam production problems or a trip.
The boiler temperature sensor is faulty (short circuit or open circuit) or its electrical...
1. Turn off the power supply to the device. 2. Access to the boiler and its sensor must be...
The device faults by reporting an inconsistency between the measurements of the safety sensor and the main outside air sensor.
One of the two sensors (main or redundant) is defective, creating a measurement deviation...
1. Unplug the device. 2. Technical expertise is essential. 3. The technician will need to...
A fault is reported on the drying air temperature measurement system, and the cycle stops for safety reasons.
A measurement discrepancy is detected between the main temperature sensor and the redundant...
1. Turn off the device. 2. Only a qualified technician can intervene. 3. It will measure...
The program is interrupted due to an inconsistency detected between the water temperature sensors.
One of the two water temperature sensors (the main or the safety one) has failed, providing...
1. Unplug the appliance. 2. Professional intervention is required to access the sensors. 3....
Miele F2065: Operational cycle fault detected during Oven / Microwave program execution.
Component fatigue, sensor feedback out of tolerance, wiring harness connector...
1. Disconnect 230V mains power for 3 minutes. 2. Inspect wire harness and edge connectors...
The device displays a general error regarding an air temperature sensor, without specifying its location.
One of the air circuit temperature sensors is defective, but the electronics cannot...
1. Turn off the device. 2. A technical diagnosis is necessary to sequentially test all air...
An error is reported regarding the entire indoor air measurement system, not just a single sensor.
The problem is more complex than a simple failed sensor, and may include wiring,...
1. Unplug the appliance. 2. Thorough diagnosis by a technician is required. 3. It will...
The device signals a fault in the complete external air temperature measurement circuit, causing a trip.
The fault may be in the sensor, its wiring, its connections, or the signal processing...
1. Turn off the power. 2. Call an authorized technical service. 3. A complete diagnosis of...
A general error related to water temperature measurement is displayed, resulting in incorrect heating or program termination.
The problem may be with the temperature sensor, its wiring harness, its connectors, or the...
1. Unplug the appliance. 2. The intervention of a technician is essential for an accurate...
Miele F2070: Operational cycle fault detected during Oven / Microwave program execution.
Component fatigue, sensor feedback out of tolerance, wiring harness connector...
1. Disconnect 230V mains power for 3 minutes. 2. Inspect wire harness and edge connectors...
The device reports an anomaly in the air measurement system, potentially affecting drying or pneumatic processes.
The airflow or pressure sensor is likely defective, clogged, or its electrical connections...
Turn off the power. Inspect the air ducts for any obstructions. Check the air sensor wiring...
Unit does not start or respond to key selector operation.
The key selector is faulty, its wiring is damaged, or the electronic card does not...
Make sure the key is correctly inserted and turned. Visually inspect the key selector and...
The selection of programs is erratic, the chosen cycle does not start, or the display does not correspond to the position of the selector.
The program selection rotary switch is worn, dirty, or has an electrical fault.
Turn off the device. Carefully clean the program selector. Check its connections on the...
Our official certified partners service Miele appliances in your area.