Access our premium database of error codes, common faults, and professional repair solutions for Miele appliances.
The device displays a diagnostic code F4213 and may stop working.
This code is an internal test error (dummy error) used by technicians. It does not indicate...
Carry out a reset by unplugging the device from the mains for 5 minutes. Reconnect and...
The device displays a diagnostic code F4213 and may stop working.
This code is an internal test error (dummy error) used by technicians. It does not indicate...
Carry out a reset by unplugging the device from the mains for 5 minutes. Reconnect and...
The current cycle is interrupted and the display indicates anomaly F4214.
An internal error has occurred in the electronic control module. This could be caused by a...
Disconnect the device from the power supply for 30 minutes to allow a complete reset....
The current cycle is interrupted and the display indicates anomaly F4214.
An internal error has occurred in the electronic control module. This could be caused by a...
Disconnect the device from the power supply for 30 minutes to allow a complete reset....
The device no longer responds to commands and reports system error F4215.
The control board microprocessor has detected a critical error in its internal data or memory.
Attempt an electrical reset by turning off the power at the circuit breaker for at least 10...
The device no longer responds to commands and reports system error F4215.
The control board microprocessor has detected a critical error in its internal data or memory.
Attempt an electrical reset by turning off the power at the circuit breaker for at least 10...
Display of code F4216, the device goes into security mode and stops all operations.
A software conflict or inconsistency in configuration settings has been detected by the...
Perform a 'hard reset' by unplugging the wall socket for around twenty minutes. Reconnect...
Display of code F4216, the device goes into security mode and stops all operations.
A software conflict or inconsistency in configuration settings has been detected by the...
Perform a 'hard reset' by unplugging the wall socket for around twenty minutes. Reconnect...
The appliance stops suddenly during the program and the code F4217 flashes on the screen.
Checksum error in the EEPROM memory of the electronic card, indicating possible corruption...
Isolate the device from the electrical network for one hour to attempt a complete reset....
The appliance stops suddenly during the program and the code F4217 flashes on the screen.
Checksum error in the EEPROM memory of the electronic card, indicating possible corruption...
Isolate the device from the electrical network for one hour to attempt a complete reset....
The control panel is blocked and error F4218 is visible.
The main electronics module has failed its self-diagnostic at startup or during operation.
Unplug the device. Wait a few minutes before plugging it back in. This can sometimes...
The control panel is blocked and error F4218 is visible.
The main electronics module has failed its self-diagnostic at startup or during operation.
Unplug the device. Wait a few minutes before plugging it back in. This can sometimes...
The device emits an audible signal and displays fault F4219, preventing any start-up.
Unspecified internal anomaly in the control circuit, potentially linked to a faulty...
Turn off the power to the device for 30 minutes. Turn the device back on. If the error...
The device emits an audible signal and displays fault F4219, preventing any start-up.
Unspecified internal anomaly in the control circuit, potentially linked to a faulty...
Turn off the power to the device for 30 minutes. Turn the device back on. If the error...
The program does not terminate and the screen displays error message F4220.
An internal processing error was identified by the device software, preventing normal...
Attempt to reset the system by unplugging the device for a short time. Reconnect and test....
The program does not terminate and the screen displays error message F4220.
An internal processing error was identified by the device software, preventing normal...
Attempt to reset the system by unplugging the device for a short time. Reconnect and test....
The device refuses to start a cycle and immediately indicates the code F4221.
Critical error detected on the main control board, often linked to an internal module power...
Check that the power outlet is working properly. Unplug the device for 15 minutes, then...
The device refuses to start a cycle and immediately indicates the code F4221.
Critical error detected on the main control board, often linked to an internal module power...
Check that the power outlet is working properly. Unplug the device for 15 minutes, then...
Operation is erratic and trouble code F4222 appears intermittently.
Instability within the electronic control module causes communication or internal logic errors.
Carry out a prolonged power outage (more than 30 minutes). Reconnect and observe the...
Operation is erratic and trouble code F4222 appears intermittently.
Instability within the electronic control module causes communication or internal logic errors.
Carry out a prolonged power outage (more than 30 minutes). Reconnect and observe the...
Complete shutdown of the device with code F4223 permanently displayed.
The integrated diagnostic system has identified an unrecoverable fault within the main...
Unplug the appliance from the wall. Wait 10 to 15 minutes. Reconnect. If the fault...
Complete shutdown of the device with code F4223 permanently displayed.
The integrated diagnostic system has identified an unrecoverable fault within the main...
Unplug the appliance from the wall. Wait 10 to 15 minutes. Reconnect. If the fault...
The device interrupts mid-cycle, displaying error code F4224.
The device firmware encountered an unexpected error condition, potentially due to a current...
Attempt a reset by turning off the main power via the circuit breaker for several minutes....
The device interrupts mid-cycle, displaying error code F4224.
The device firmware encountered an unexpected error condition, potentially due to a current...
Attempt a reset by turning off the main power via the circuit breaker for several minutes....
The screen displays F4225 and the device no longer responds to any user commands.
Internal communication error between the different components of the main control board.
Perform an electrical reset by unplugging the unit for half an hour. Reconnect and test. If...
The screen displays F4225 and the device no longer responds to any user commands.
Internal communication error between the different components of the main control board.
Perform an electrical reset by unplugging the unit for half an hour. Reconnect and test. If...
A fault code F4226 is reported, blocking further operation of the device.
Hardware failure of a component on the electronic board, such as a relay or microcontroller.
Isolate the device from the mains for at least 20 minutes to clear the volatile memory....
A fault code F4226 is reported, blocking further operation of the device.
Hardware failure of a component on the electronic board, such as a relay or microcontroller.
Isolate the device from the mains for at least 20 minutes to clear the volatile memory....
The program stops and the code F4227 appears, indicating an electronic problem.
Inconsistency detected in software configuration or data stored in control board memory.
Perform a force restart by unplugging from the wall outlet for 15 minutes. If fault F4227...
The program stops and the code F4227 appears, indicating an electronic problem.
Inconsistency detected in software configuration or data stored in control board memory.
Perform a force restart by unplugging from the wall outlet for 15 minutes. If fault F4227...
Our official certified partners service Miele appliances in your area.