Skip to content

CodesErreur.comSWISS PRO ENGINE

Core Diagnostics

Diagnostics Brands OEM Manuals Specialists AI EngineerPRO

Workshop Tools

Diagnostic ToolsNEW

Hardware interfaces & test probes

Find Rating Plate

Locate exact E-Nr, PNC & serial codes

Global OEM spare parts suppliers

Community & Career

Academy & Courses

Masterclasses by senior technicians

Certification ExamsPRO

Verify your B2B technical credentials

Peer-to-peer field troubleshooting

B2B recruitment & field opportunities

Global ranking of verified specialists

Certified Appliance Engineering EcosystemApply for Certification →

Language Selector

Account & Access

Ignis • Central Diagnostic Dictionary

138 Verified Codes in Database

Ignis Error Codes & Diagnostics

Access our premium database of error codes, common faults, and professional repair solutions for Ignis appliances.

Luxury front-loading washing machine in brushed titanium with illuminated dark glass drum

Ignis — Known Error Codes

CodeAppliancesFault / DiagnosticsRepair InstructionsAction

F27

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

Ignis LTE Top-Loader & TuttoinUno Front-Loader Washing Machine: Drum reversing motor relay contact stuck F27; motor can rotate in only one direction due to welded relay contacts.

On Ignis washing appliances: High inductive arc discharge during drum reversal under heavy laundry load welding reversing relay contacts on PCB.

De-energize machine. Tap relay casing lightly or measure contact continuity with power off (normally open contacts must read infinite ohms). Replace PCB relay. Hold Start/Cancel button for 5 seconds until indicator light turns solid, switch off, and turn knob to 0.

F28

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

Ignis LTE Top-Loader & TuttoinUno Front-Loader Washing Machine: Motor stator tap field weakening failure F28; high-speed spin field switching relay does not engage.

On Ignis washers: Open circuit in stator intermediate winding tap, broken motor wiring harness terminal, or defective field-weakening relay.

Measure resistance across stator tap winding connections on motor terminal block (nominal 1.2–2.5 Ω). Check 12V DC coil activation on field relay. Hold Start/Cancel button for 5 seconds until indicator light turns solid, switch off, and turn knob to 0.

F29

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

Ignis LTE Top-Loader & TuttoinUno Front-Loader Washing Machine: Door lock interlock failure F29; latch microswitch contact fails to close within 15 seconds of cycle start command.

On Ignis washing appliances: Broken door latch hook, sagging door hinges, burnt PTC wax tablet, or open solenoid coil in motorized door lock.

Inspect door latch alignment with front strike plate. Measure door lock solenoid resistance (nominal 800–1100 Ω) or PTC tablet (700–1200 Ω). Replace lock mechanism. Hold Start/Cancel button for 5 seconds until indicator light turns solid, switch off, and turn knob to 0.

F36

Hob / Cooktop

NTC Temperature Sensor & Thermistor

Ignis Platino Induction & Ceramic Cooktop: Front left induction coil NTC sensor calibration drift F36; analog voltage reading indicates out-of-range temperature curve.

On Ignis cooktops: Thermal degradation of sensor bead due to repeated overheating, dry silicone thermal coupling, or moisture on sensor connector.

Measure front left coil NTC resistance: ~100 kΩ at 25°C (falling to ~10 kΩ at 80°C). Clean sensor contact face and renew thermal paste. Replace NTC if drifted. Power down at breaker switch for 60 seconds, wipe surface dry with microfiber cloth, then restart.

F37

Hob / Cooktop

Heating Element, Thermostat & Safety Fuse

Ignis Platino Induction & Ceramic Cooktop: Power board mains input voltage out of tolerance F37; line monitoring circuit detects voltage below 160V or exceeding 285V RMS.

On Ignis cooktops: Electrical grid brownout, defective neutral bonding in home panel, or degraded voltage sensing resistor divider on filter board.

Test mains supply voltage at cooktop terminal block under load. If household supply is normal (230V ± 10%), inspect voltage sensing circuit on filter PCB. Power down at breaker switch for 60 seconds, wipe surface dry with microfiber cloth, then restart.

F40

Hob / Cooktop

Drive Motor, Inverter & Tachometer Sensor

Ignis Platino Induction & Ceramic Cooktop: Left induction generator module bus communication failure F40; power inverter microcontroller fails to respond to poll command.

On Ignis cooktops: Open circuit on internal serial data link, blown auxiliary low-voltage fuse on left generator, or failed power supply regulator.

Check internal bus wiring connecting left generator board. Verify onboard SMD fuses (T3.15A / T2A) and test 5V DC and 12V DC power supply rails. Power down at breaker switch for 60 seconds, wipe surface dry with microfiber cloth, then restart.

F42

Hob / Cooktop

General System & Mechanical Integration

Ignis Platino Induction & Ceramic Cooktop: Incorrect mains line supply connection F42; 400V phase-to-phase accidentally wired to 230V phase-to-neutral terminal.

On Ignis cooktops: Missing neutral copper link bridge on terminal board, or neutral connected to second 400V live line in domestic wall junction.

Shut off power immediately. Inspect terminal box wiring diagram. Install copper bridge between N1 and N2 terminals. Verify true Neutral (0V to Earth). Power down at breaker switch for 60 seconds, wipe surface dry with microfiber cloth, then restart.

F47

Hob / Cooktop

Heating Element, Thermostat & Safety Fuse

Ignis Platino Induction & Ceramic Cooktop: LIN bus communication lost between touch UI and power filter PCB F47; master controller drops link to auxiliary filter board.

On Ignis cooktops: Loose multi-pin LIN bus connector, moisture condensation on filter board transceiver, or blown power supply resistor.

Inspect LIN bus harness connecting touch UI and filter PCB. Reseat connectors firmly. Verify 12V DC input to filter transceiver IC. Replace harness if damaged. Power down at breaker switch for 60 seconds, wipe surface dry with microfiber cloth, then restart.

FA

Dishwasher

Drainage System & Drain Pump

Ignis ADL & TuttoinUno Platinum Compact Dishwasher: Optical Water Indicator (OWI) turbidity sensor failure FA; infra-red optoelectronic receiver signal distorted or disconnected.

On Ignis dishwashers: Soil deposition on OWI prism lenses, defective phototransistor diode, or wiring harness disconnect on base sump interface.

Clean optical prism face of OWI sensor inside sump. Verify 5V DC supply and signal line to main board. Replace OWI sensor assembly if cleaning fails. Press and hold Start button for 5 seconds to force drain cycle, wait 60s, then switch off power switch.

FB

Dishwasher

Drainage System & Drain Pump

Ignis ADL & TuttoinUno Platinum Compact Dishwasher: Motorized Diverter Valve (MDV) microswitch failure FB; cam switch does not pulse during diverter disc positioning.

On Ignis dishwashers: Broken nylon gear teeth in MDV actuator, burnt drive motor winding, or oxidized internal microswitch wiper contacts.

Measure MDV synchronous drive motor resistance (6.0–7.5 kΩ). Check microswitch continuity with manual gear rotation (must switch between 0 Ω and infinite). Replace MDV. Press and hold Start button for 5 seconds to force drain cycle, wait 60s, then switch off power switch.

FC

Dishwasher

Drainage System & Drain Pump

Ignis ADL & TuttoinUno Platinum Compact Dishwasher: Water softener hardness sensor circuit fault FC; salt concentration conductivity measurement signal interrupted.

On Ignis dishwashers: Salt bridge in brine tank preventing sensor contact, corroded conductivity electrode pins, or disconnected softener wiring harness.

Stir salt container with wooden spoon to break crusts. Add 500ml warm water. Clean electrode pins and check wiring continuity to main control PCB. Press and hold Start button for 5 seconds to force drain cycle, wait 60s, then switch off power switch.

FDL

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

Ignis LTE Top-Loader & TuttoinUno Front-Loader Washing Machine: Door lock latching failure FDL; door lock mechanism fails to mechanically secure drum hatch before cycle startup.

On Ignis washing appliances: Misaligned door catch, foreign object in lock aperture, burnt door lock solenoid, or broken locking pawl slider.

Press firmly on door latch zone. Clear debris from strike hole. Measure lock solenoid resistance (800–1100 Ω). Replace motorized door lock if open circuit. Hold Start/Cancel button for 5 seconds until indicator light turns solid, switch off, and turn knob to 0.

FDU

Washing Machine

Drainage System & Drain Pump

Ignis LTE Top-Loader & TuttoinUno Front-Loader Washing Machine: Door unlock release failure FDU; lock mechanism fails to release door latch at cycle end despite unlock pulse.

On Ignis washing appliances: Residual water detected in drum by pressure sensor, mechanical lock slider jammed, or burnt unlock solenoid coil.

Verify drum is fully drained (run drain program if water remains). Use emergency door release pull-tab behind kickplate filter flap. Replace door interlock. Hold Start/Cancel button for 5 seconds until indicator light turns solid, switch off, and turn knob to 0.

FE

Dishwasher

Drainage System & Drain Pump

Ignis ADL & TuttoinUno Platinum Compact Dishwasher: Control board microcontroller EEPROM checksum failure FE; corrupted non-volatile memory parameters abort wash cycle.

On Ignis dishwashers: Electrical transient spike during cycle writing, low voltage on 5V logic rail, or aging EEPROM memory cell leakage.

Unplug dishwasher for 15 minutes to allow capacitor discharge. If error persists, reprogram firmware using factory service interface or replace main PCB. Press and hold Start button for 5 seconds to force drain cycle, wait 60s, then switch off power switch.

FH

Washing Machine

Water Inlet Valve, Aquastop & Flowmeter

Ignis LTE Top-Loader & TuttoinUno Front-Loader Washing Machine: No water tap flow detected FH; flowmeter turbine generates zero impulse count during initial filling phase.

On Ignis washing appliances: Supply tap turned off, kinked inlet hose, lime scale encrusted in flowmeter turbine chamber, or disconnected reed sensor.

Open tap fully. Clean inlet hose filters. Verify flowmeter reed switch pulses with multimeter on continuity during filling. Replace flowmeter if jammed. Hold Start/Cancel button for 5 seconds until indicator light turns solid, switch off, and turn knob to 0.

FOD

Washing Machine

Drainage System & Drain Pump

Ignis LTE Top-Loader & TuttoinUno Front-Loader Washing Machine: Foam on drain lock condition FOD; drain pump impeller cavitates inside aerated foam chamber during pump out.

On Ignis washing appliances: Soft water area with standard detergent dosage, or washing porous fabrics (curtains, woolens) producing massive air bubbles.

Pour 2 liters of water with 1 cup of white vinegar into drum to collapse suds. Run drain cycle. In soft water zones, reduce soap dose by 40%. Hold Start/Cancel button for 5 seconds until indicator light turns solid, switch off, and turn knob to 0.

PO

Refrigerator / Freezer

Heating Element, Thermostat & Safety Fuse

Ignis Combi Double Door Total NoFrost Refrigerator: Power outage alert PO indicates extended mains interruption; internal temperature rose above safe food storage threshold.

On Ignis refrigerators (Ignis heavy-duty electromechanical chassis and Arcadia / L1373 hybrid control architecture): External blackout, tripped electrical safety breaker, loose wall receptacle, or momentary neutral voltage drop.

Verify freshness and temperature of frozen perishables. Check wall socket voltage (230V AC ±10%). Silence buzzer and acknowledge alarm: Press thermostat reset or super button for 3 seconds to cancel temperature alarm and re-arm cooling.

SUD

Washing Machine

Drainage System & Drain Pump

Ignis LTE Top-Loader & TuttoinUno Front-Loader Washing Machine: Excessive suds detection SUD; electronic pressure transducer senses thick foam blanket stalling drain pump motor.

On Ignis washing machines: Massive overdose of concentrated laundry detergent, incorrect high-foaming hand-wash soap, or restricted siphon pipe.

Pause cycle and allow foam to dissipate for 20 minutes. Run cold rinse cycle without soap. Inspect drain filter coin trap for lint obstructions. Hold Start/Cancel button for 5 seconds until indicator light turns solid, switch off, and turn knob to 0.

← Previous PagePage 5 of 5 (138 results)

Next Page →

Ignis — Complete Error Code Catalog

78 Verified Error Codes

Server-side index of all verified manufacturer error codes for technicians and automated crawlers.

Dishwasher28

E1 E2 E3 E4 E5 E6 E7 E8 E9 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 FA FB FC FE

Washing Machine12

BDD F16 F18 F26 F27 F28 F29 FDL FDU FH FOD SUD

Tumble Dryer14

F01 F02 F03 F04 F05 F06 F07 F08 F09 F20 F21 F22 F23 F24

Oven / Microwave4

F1E F2E F3E F6E

Hob / Cooktop11

C81 C82 C83 C84 C85 F25 F36 F37 F40 F42 F47

Refrigerator / Freezer9

A1 A2 AL01 AL02 AL03 CE CF dE PO

Need Help? Call a Certified Technician

Our official certified partners service Ignis appliances in your area.

Electroassistance (Switzerland)Appliance Care UK (United Kingdom)

CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search Database PRO Diagnostic AIPRO Diagnostic Tools Brands

Workshop Tools

Brands (87)OEM Manuals Find Rating Plate Parts Locator

For Technicians

Specialists Technician Forum Tech Jobs Premium

Corporate

Terms of Service Privacy PolicyOfficial Swiss Repair Partner: Electroassistance

OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Official Swiss Repair Partner: Electroassistance Terms of Service Privacy Policy