Access our premium database of error codes, common faults, and professional repair solutions for Miele appliances.
The device displays the code F1085 and refuses to start a wash cycle.
Data relating to washing programs is corrupted or missing in the memory of the Profitronic...
The software containing the washing programs must be reinstalled. This complex procedure...
Error F1086 appears, indicating a problem with cycle data logging.
The system cannot access or write wash protocols (cycle logs) to the device memory.
A diagnosis of the internal memory of the Profitronic module is necessary. Contact Miele...
Error code F1087 is seen, indicating an inability to manage the error log.
Memory allocated to error protocols is full, defective, or inaccessible.
A Miele technician is required to clear, repair or replace the error history memory.
A printer message displays and cycle report prints fail.
Communication problem with external printer, or the printer itself is offline, out of...
Make sure the printer is properly connected, turned on, and has paper and ink. Check the...
The device refuses to start and displays a message relating to the sequence of electrical phases.
The phase order of the three-phase power supply is incorrect, causing the motor to fail.
This operation must be carried out by a qualified electrician. Turn off the power and have...
The message “Battery wechseln” (Change battery) appears on the control screen.
The backup battery for the clock and settings on the electronic board is low or exhausted.
Check the user manual to locate the battery. Replace the battery (usually CR2032)...
The device shut down unexpectedly displaying a load shedding message.
The peak load management system has detected a timing conflict or error, resulting in a...
Check the energy management system settings if the device is connected to such a device....
The cycle has been interrupted and the device displays "Netzausfall".
A power failure has occurred during operation of the device.
Validate the message by pressing “OK”. The device will offer to resume the program where it...
Code F1093 is displayed and the unit's motor is not running properly or at all.
The tachometer generator (engine rotation speed sensor) is defective or its connection is...
This repair requires technical expertise. Miele customer service should be contacted to...
An error message regarding saving operating parameters appears.
The system failed to save current operating parameters, potentially due to a non-volatile...
Try restarting the device by unplugging it for a few minutes. If the message persists,...
The device displays a critical alert F1095 related to saving general settings.
A serious error occurred while attempting to save device settings, potentially resulting in...
Do not attempt any manipulation. Contact Miele Service immediately to avoid irreversible...
The F1096 code is displayed, indicating a program backup failure.
The system was unable to save wash program data, which may cause them to malfunction or...
Technical intervention is essential. Miele customer service will need to diagnose the...
Error F1097, the appliance stops during the drying phase or does not dry effectively.
An abnormal temperature difference has been detected in the drying air circuit, indicating...
Check that the filters and air ducts are not blocked. If everything is clean, contact Miele...
The “External Error 1” code appears, indicating a problem with a connected device.
The machine received an error signal from a connected external module, such as an automatic...
Consult the external module manual to identify the meaning of the error. Fix the problem on...
The display shows "External Error 2", indicating a device malfunction.
A second type of error signal was issued by an external device connected to the machine.
Identify the external device causing the error. Check its connections, its operational...
The device has paused and displays "External Error 3".
A third error signal, coming from peripheral equipment, was detected by the control unit.
Diagnosis should focus on external equipment. Control his diet and communication. Correct...
The message "External error 4" interrupts normal operation.
The Miele appliance received a fourth separate error alert from a connected third-party system.
Review the external system diagnostic logs. Make sure the configuration of the...
The “External Error 5” code is displayed, blocking use of the machine.
A fifth type of fault was reported by an external device, for example a water treatment system.
Refer to the external component's troubleshooting guide. Check its consumables and...
The display indicates "External error 6" and the program is suspended.
A sixth fault signal from an accessory module was recorded.
Isolate the responsible external module. Check its wiring to the Miele appliance. Contact...
The message “External error 7” is present on the display and blocks the cycle.
A seventh specific error code was transmitted by connected equipment.
Carry out a systematic check of all external devices. Restart each device one by one to...
The device is stopped with the indication "External error 8".
An eighth error signal, potentially related to a safety condition, was received from an...
The origin of the problem lies with the external device. Make sure all its security...
Operation is interrupted by the message "External error 9".
The control unit has detected a ninth type of problem communicated by a connected device.
Troubleshooting must be done on external equipment. Verify the integrity of the...
The display signals “External error 10”, preventing startup.
A tenth distinct error signal was sent to the machine by a peripheral system.
Refer to the external system technical documentation to interpret this specific code....
A custom, non-standard error message is displayed on the screen.
A specific error message has been programmed by a technician to report a particular...
Read the displayed message carefully as it usually contains specific instructions. If the...
The device displays a message “Salzmangel” (Lack of salt) or a corresponding indicator light is lit.
The regenerating salt level in the water softener tank is too low.
Open the salt reservoir cap, located at the bottom of the tank. Fill the reservoir with...
A “Regenerieren” message is displayed, and the device may appear inactive.
The internal water softener is undergoing a regeneration cycle to restore its ability to...
No action is required. Allow the device to complete its regeneration process. The message...
An error message regarding the steam condenser is displayed, sometimes with steam leaks.
The steam condenser is clogged, defective, or its cooling water circuit is not functioning...
Check that the cold water inlet of the appliance is turned on and that the pressure is...
The device stops mid-cycle and reports an error. The leak protection system (Waterproof System) is activated.
An internal leak caused water to accumulate in the lower drain pan, tripping the safety...
Unplug the appliance electrically. Inspect all internal components (pipes, pump, seals,...
The appliance does not fill with cold water or the filling does not stop, causing the cycle to be interrupted.
The cold water inlet solenoid valve is defective, either electrically (cut coil) or...
Turn off the water supply and unplug the appliance. Check the connections of the cold water...
The program is interrupted because the appliance cannot fill with hot water, or it is overfilled.
The solenoid valve dedicated to the hot water inlet has an electrical or mechanical fault.
Close the hot water tap and disconnect the appliance from the mains. Check the solenoid...
Our official certified partners service Miele appliances in your area.