Access our premium database of error codes, common faults, and professional repair solutions for Miele appliances.
The automatic dosing system (AutoDos) reports a cold water filling error.
The solenoid valve specific to the cold water inlet for the AutoDos circuit is faulty.
Cut off the water supply and the electricity supply. Locate the cold water solenoid valve...
Hot water filling anomaly reported by the automatic dosing system (AutoDos).
The hot water inlet solenoid valve dedicated to the AutoDos system is defective.
Put the appliance out of service by cutting off the water and electricity. Access the...
The AutoDos system fails to collect detergent and reports a water fill anomaly.
One of the general solenoid valves of the AutoDos filling system is defective.
Turn off the appliance and shut off the water supply. Identify and test the solenoid valves...
An internal test code is displayed, normally not visible to the end user.
This code is used during end of factory assembly line testing. Its appearance may result...
Attempt to exit service mode by completely turning off the device via a mains disconnection...
The cycle is interrupted with a filling or water level error linked to the buffer tank.
A malfunction is detected in the intermediate tank filling system (obstruction, leak,...
Unplug the device. Access the intermediate tank to check for obstructions in the hoses....
The appliance displays a 'Dosage A' error and the detergent distribution is incorrect.
The dosing monitoring system has detected an abnormality A, potentially a blocked dosing...
Check the presence and correct insertion of the cartridges. Access the dosing module to...
The washing machine reports a 'Dosage B' error and the automatic dosage does not work as expected.
The dosage monitoring system identified an anomaly B, linked to a mechanical (pump, pipe)...
Make sure consumables are correct. Examine the dosing module for blockages. Electrically...
Display of error 'Dosing C', indicating a problem with the automatic dosing system.
The dosage control system has detected a C fault, which could be an obstruction, a seized...
After checking the cartridges, carefully inspect the dosing module. If the mechanical...
A 'Dosage D' error is displayed, the detergent is not or is incorrectly distributed.
Abnormality D detected by the dosage monitoring system, likely involving a hardware or...
Carry out the basic checks (cartridges, absence of visible blockage). Perform a test of the...
'Dosage E' error message relating to the automatic detergent dispensing system.
The system has recorded an E error condition, indicating a failure in the dosing circuit,...
Inspect the entire dosing module. Check the cleanliness of the ducts. Test the operation of...
The screen displays a message inviting you to contact Miele customer service, sometimes with a specific number.
The electronics have detected a critical internal error or combination of errors that...
Note the complete error code. Attempt a reset by unplugging the device for 10 minutes. If...
The displayed cycle time is inconsistent, or the program stops due to a timing error.
Malfunction of the internal clock (time base) of the Profitronic electronic control card.
Perform a complete reset of the device by unplugging it from the mains. If the time anomaly...
An undocumented error code is displayed, blocking normal operation of the device.
The electronics have recorded an undefined error state, often due to software corruption or...
Attempt a reset by unplugging the device. Check the Miele website for possible software...
An error code not listed in the standard documentation is displayed by the device.
This error code is likely reserved for future use by the manufacturer or corresponds to an...
Perform a standard reset of the device by unplugging it. If the code persists and affects...
The device displays an error code that is not described in the user or service manual.
Error code not publicly defined, potentially for factory diagnostics or future features.
Carry out a reset of the device by cutting off the power supply. If this persists, a...
An unidentified trouble code appears on the device screen.
This is a Miele reserved service code, not intended for user or standard repairer diagnosis.
The first step is to reset the device. If the error reappears, it is imperative to call an...
The device displays a code indicating no fault, often after a diagnostic program.
This code confirms that no fault has been detected by the device's self-diagnostic system.
No action is required. This code is purely informative and confirms good working condition....
The device refuses to start and displays an alert regarding the 'clean' side door.
The door on the 'clean' side is not properly closed or its lock sensor is not transmitting...
Make sure the clean side door is closed securely without obstruction. Check the locking...
The cycle is prevented from starting by an error message indicating a problem with the door on the 'dirty' side.
The door on the 'dirty' side is open or the closing detection system is faulty.
Close the door on the dirty side firmly. Check the alignment of the door and the latch....
The device does not start and reports a generic door error.
The door is not closed correctly, the locking system is blocked, or the door safety...
Open and close the door firmly. Check that no laundry is stuck in the joint. Examine the...
A permanent fault on the 'clean' side door is reported, even when closed, making starting impossible.
The locking system (electric lock) or the door closing sensor on the 'clean' side is...
Unplug the device. Access the locking mechanism of the door in question. Check the...
A persistent error message indicates a door failure on the 'dirty' side, blocking all operation.
Electrical or mechanical failure of the locking system or door sensor on the 'dirty' side.
Turn off the device. Inspect the locking system of the affected door. Check the wiring and...
The device cannot operate and reports a general door system fault.
The electronic module is not receiving a correct signal from the door lock system. The...
After powering off, check the integrity of the locking mechanism. Measure the continuity of...
The device displays an error related to the upper door control.
Problem with the upper control mechanism, actuator or door position sensor.
Disconnect the power supply. Examine the upper door operating mechanism, its connections,...
A fault is reported in the lower control of the door system, preventing operation.
The lower door operating mechanism, its motor, or its position sensor is faulty.
Turn off the power supply. Access the bottom of the door system to inspect the motor, gears...
An informative message asks you to close the door on the 'clean' side to start a cycle.
The 'clean' side door is physically open or the sensor does not correctly detect its closure.
Make sure the clean side door is properly latched. If the message persists, check the...
The appliance displays an instruction to close the door on the 'dirty' side before starting a program.
The door on the 'dirty' side is left open or is not detected as closed by the system.
Close the door on the dirty side. If the alert does not go away, inspect the door latch and...
The cycle refuses to start, the control screen indicating that both doors of the appliance are open.
Both doors are not properly engaged in their locking mechanisms, or the door closing...
Make sure both doors are firmly closed until you hear a confirming click. Check that no...
The appliance does not start the selected program and displays an error message indicating an open door.
The main door or a cargo door is not fully latched, preventing the safety system from...
Close the door in question with firm pressure and check that the latch is properly engaged....
The water stagnates in the tank at the end of the program or during the cycle, and the device faults with a drain error code.
The evacuation circuit is blocked. The blockage may be in the drain filter, the pump, or...
Turn off the power. Access the drain filter, generally located at the bottom of the facade,...
Our official certified partners service Miele appliances in your area.