Skip to content

CodesErreur.comSWISS PRO ENGINE

Core Diagnostics

Diagnostics Brands OEM Manuals Specialists AI EngineerPRO

Workshop Tools

Diagnostic ToolsNEW

Hardware interfaces & test probes

Find Rating Plate

Locate exact E-Nr, PNC & serial codes

Global OEM spare parts suppliers

Community & Career

Academy & Courses

Masterclasses by senior technicians

Certification ExamsPRO

Verify your B2B technical credentials

Peer-to-peer field troubleshooting

B2B recruitment & field opportunities

Global ranking of verified specialists

Certified Appliance Engineering EcosystemApply for Certification →

Language Selector

Account & Access

Arthur Martin • Central Diagnostic Dictionary

191 Verified Codes in Database

Arthur Martin Error Codes & Diagnostics

Access our premium database of error codes, common faults, and professional repair solutions for Arthur Martin appliances.

Luxury front-loading washing machine in brushed titanium with illuminated dark glass drum

CodeAppliancesFault / DiagnosticsRepair InstructionsAction

E50

Tumble Dryer

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Motor drive general malfunction E50; drum drive motor fails to turn or stops unexpectedly during tumble sequence.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Motor run capacitor degraded (nominal 7–10 μF), defective motor windings (main ~18–25 Ω, aux ~22–30 Ω), open thermal cut-out, or drive triac failure.

Measure motor run capacitor with capacitance meter (must read within ±5% of rating). Check winding resistances with ohmmeter. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E50

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Motor drive general alarm E50; motor drive system failure stopping drum rotation during cycle.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Worn carbon brushes (< 15 mm length) on universal motor, broken drive belt, inverter module trip, or motor thermal protector tripped.

Inspect motor carbon brushes (replace if < 15 mm). On inverter brushless models, verify free drum rotation and inspect inverter board. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E51

Tumble Dryer

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Motor drive triac short circuit E51; motor runs immediately at power-on without safety control or program start.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Shorted motor triac on power board (anode 1 to anode 2 reads 0 Ω), shorted snubber capacitor, or continuous gate drive voltage from faulty microcontroller.

Disconnect power and check triac terminals A1-A2 with ohmmeter. If 0 Ω, replace triac (e.g. BTB16-600BW) or replace main control module. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E51

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Motor drive triac short circuit E51; universal motor spins at maximum uncontrolled speed immediately at start.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Power triac on main PCB short-circuited (anode to cathode breakdown), motor field winding grounded, or carbon dust buildup bridging terminals.

Blow compressed air across motor terminal block to clear carbon dust. Measure motor insulation resistance to ground (> 10 MΩ). Replace main PCB triac. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E52

Tumble Dryer

Heating Element, Thermostat & Safety Fuse

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Motor thermal protector tripped E52; motor halts during high ambient temperature or heavy load operation.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Motor internal Klixon thermal switch opened (> 135°C), lint accumulation obstructing cooling blower wheel, seized drum support rollers, or excessive laundry load.

Allow motor to cool for 45 minutes. Vacuum fluff from motor housing and cooling fan. Spin drum by hand to verify roller bearings spin freely without binding. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E52

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Motor tachometer generator failure E52; motor starts briefly, judders, and stops without speed regulation.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Tachometer coil open circuit (nominal 130–220 Ω on universal motor), loose magnet ring detached from rear motor shaft, or broken wiring.

Measure tachometer coil resistance across motor pins 1 and 2 (expected 130–220 Ω). Check that magnet ring is securely tightened on motor shaft. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E53

Tumble Dryer

Heating Element, Thermostat & Safety Fuse

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Motor triac sensing circuit fault E53; microprocessor detects inconsistent voltage across triac output terminals.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Degraded SMD feedback resistors on control board, cracked solder joints around motor relay/triac section, or power surge damage.

Remove main control board and inspect PCB under magnification for burned SMD resistors or broken solder joints near motor terminals. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E53

Washing Machine

Heating Element, Thermostat & Safety Fuse

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Motor triac sensing circuit faulty E53; microprocessor receives out-of-range sensing voltage from motor triac.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Resistor network on PCB triac sensing line open or drifted, damaged optocoupler feedback diode, or cracked solder joint on power board.

Inspect main control board for thermal discoloration around motor triac heat sink. Resolder cracked joints or replace motherboard. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E54

Tumble Dryer

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Motor jammed or drum blocked E54; motor hums but fails to rotate, or drive belt broken/derailed from pulley.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Poly-V drive belt snapped or slipped, motor starting capacitor dried out (0 μF reading), foreign object wedged between drum and seal, or seized motor bearings.

Check drum drive belt and spring-loaded tensioner pulley. Test motor capacitor with multimeter (replace if < 85% rated μF). Verify drum turns smoothly by hand. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E54

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Motor reversing relay contacts welded E54; drum rotates in only one direction or motor locks in place.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Electrical arcing welded contacts of motor direction reversal relays (RL1/RL2) on main PCB due to heavy drum load or high startup surge.

De-energize machine. Tap reversing relays gently with plastic handle to free stuck contacts, or replace 12V DC relays / main PCB. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E57

Tumble Dryer

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Heat pump compressor inverter overcurrent E57; inverter safety shutdown triggered to protect compressor windings.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Heat pump compressor mechanical lock, shorted IGBT module on inverter drive board, high refrigeration head pressure from clogged condenser, or low line voltage.

Clean heat pump lower condenser fins thoroughly. Disconnect compressor harness and measure 3-phase windings (equal resistance ~6–12 Ω between each pair). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E57

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Inverter module overcurrent fault E57; peak inverter current exceeds 15A threshold during motor acceleration.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Short-circuited stator winding in 3-phase inverter motor, seized drum bearings creating severe mechanical resistance, or shorted IGBT power bridge.

Rotate drum by hand to confirm free mechanical movement. Measure winding resistance across all three motor phases U-V, V-W, W-U (must be strictly balanced: 5–8 Ω each). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E58

Tumble Dryer

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Heat pump compressor phase current exceeded E58 (> 4.5A); drive board limits frequency to prevent inverter thermal destruction.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Extreme refrigeration circuit load due to saturated air filters, failing compressor capacitor (on non-inverter models) or internal piston friction.

Clean dual lint filters under running water and let dry completely. Vacuum heat exchanger duct. Measure live running current with clamp meter. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E58

Washing Machine

Drainage System & Drain Pump

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Inverter motor phase current overload E58; continuous phase current exceeds 4.5A for > 5 seconds.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Excessive wash load weight, laundry jammed between tub and drum lip, foreign object caught in drain tub boot, or demagnetized rotor.

Remove excess laundry load. Check clearance between drum lip and front door gasket. Measure phase-to-phase stator balance with multimeter. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E59

Tumble Dryer

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: No tachogenerator feedback signal E59; drum motor stops after 5 seconds of unmonitored rotation attempt.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Detached or cracked tacho ring magnet on motor shaft, open tachogenerator coil (nominal 115–220 Ω), or disconnected wiring to inverter/main board.

Measure tachogenerator coil resistance across motor pins (115–220 Ω). Rotate motor pulley by hand while measuring AC millivolts (1–3V AC). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E59

Washing Machine

Drive Motor, Inverter & Tachometer Sensor

Arthur Martin Electrolux AWF Series / Silence Plus Washer: No tachometer signal from 3-phase inverter motor E59 for > 3 seconds after inverter activation.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Internal Hall sensor / tachometer coil open circuit, loose wiring connector on motor rear, or broken wire in inverter wiring loom.

Check wiring continuity between inverter board connector and motor tachometer pins. Measure tachometer coil resistance (nominal 110–135 Ω on inverter motor). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E60

Tumble Dryer

Heating Element, Thermostat & Safety Fuse

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Heating system general failure E60; air inside drum remains cold and cycle runs excessively long without drying clothes.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Open heating element coils (dual element: ~25 Ω and ~35 Ω), tripped manual/automatic safety thermostat, defective heating relay on PCB, or compressor fault in heat pump.

Disconnect dryer and remove rear heating duct cover. Measure resistance of both heating elements with ohmmeter. Check continuity through safety thermostats (< 1 Ω). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E60

Washing Machine

NTC Temperature Sensor & Thermistor

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Water heating general malfunction E60; wash water temperature fails to increase during programmed heating phase.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Wash heating element open circuit (nominal 24–28 Ω), wash NTC thermistor out of calibration, safety heater relay coil open on PCB, or thick limescale encrustation.

Measure resistance across heating element spade terminals with multimeter (nominal 24–28 Ω at 230V, ~1950W). Check NTC resistance (4.8–6.0 kΩ at 20°C). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E61

Tumble Dryer

Refrigeration Compressor, Defrost Heater & PTC Relay

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Insufficient heating rate E61; temperature rise inside drum during first 20 minutes is below calibrated threshold.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: One of two heating elements open (operating at half power), degraded heat pump refrigerant charge (R134a / R290 leak), or severely restricted airflow.

Test individual heating coils (Element 1: ~35 Ω, Element 2: ~25 Ω). Thoroughly clean air ducts and condenser pack. Inspect heat pump lines for oil stains. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E61

Washing Machine

NTC Temperature Sensor & Thermistor

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Insufficient heating rate alarm E61; wash water heating speed is less than 0.5°C per minute under full power.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Heavily calcified heating element preventing heat transfer to water, partial coil burn, low mains supply voltage, or incorrect wash NTC positioning.

Remove heating element and inspect for limescale jacket (descale or replace). Ensure NTC bulb is pushed fully into rubber gasket pocket. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E62

Tumble Dryer

NTC Temperature Sensor & Thermistor

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Overheating alarm E62; drum temperature exceeds maximum safety limit (> 95°C) and cycle halts immediately.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Stuck closed heating relay contact on PCB (continuous power to heater), blocked lint filter stopping heat dissipation, or defective forward duct NTC sensor.

Inspect heating relay on control board (ensure contacts open when unpowered, resistance ∞ Ω). Clean all lint filters and measure front duct NTC resistance (~5–6 kΩ at 25°C). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E62

Washing Machine

NTC Temperature Sensor & Thermistor

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Water overheating alarm E62; wash temperature exceeds 88°C for > 5 minutes triggering safety cutoff.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Heating element power relay contact welded closed on main PCB (continuous unswitched 230V power), shorted wash NTC sensor, or MCU logic fault.

Turn machine off immediately. Measure voltage at heating terminals with program off (must be 0V AC; if 230V AC is present, replace stuck relay / PCB!). Test NTC sensor. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E63

Tumble Dryer

Heating Element, Thermostat & Safety Fuse

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Safety thermostat tripped E63; one-shot thermal fuse or manual reset button on heater housing has opened.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Severe airflow blockage from saturated lint filter or condenser, failed exhaust blower wheel, or motor stalled while heating element was energised.

Remove rear duct panel. Press red reset button on Klixon thermostat if present (verify 0 Ω continuity). Clean complete air circulation path thoroughly. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E66

Washing Machine

Heating Element, Thermostat & Safety Fuse

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Heating element power relay faulty E66; incongruence between relay command and sensing contact status.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Safety heater relay coil open circuit (nominal 400 Ω), oxidized power contacts with high internal drop, or defective relay sensing circuit on PCB.

Test 12V DC heating relay coil on main PCB (expected ~400 Ω). Check continuity of closed contacts under test excitation. Replace relay or PCB. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E68

Washing Machine

Heating Element, Thermostat & Safety Fuse

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Heating element high leakage current to earth E68; leakage current exceeds 2.5 mA causing insulation alarm.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Microscopic cracks in stainless steel sheath of heating element allowing water into magnesium oxide core, breaking down galvanic isolation.

Disconnect both faston leads from heating element. Test insulation resistance to earth with 500V megohmmeter (must be > 10 MΩ; replace element if < 2 MΩ!). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E69

Washing Machine

Heating Element, Thermostat & Safety Fuse

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Heating element open circuit E69; heating coil is interrupted or wiring harness disconnected.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Burnt heating element filament (infinite resistance ∞ Ω), thermal fuse blown inside heating flange, or disconnected spade terminal.

Measure resistance across heater pins with multimeter (expected 24–28 Ω; if infinite ∞ Ω, replace heating element). Ensure tight faston fit. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E70

Tumble Dryer

NTC Temperature Sensor & Thermistor

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Temperature sensor NTC general error E70; electronic control fails to read valid analog temperature input.

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: NTC sensor open circuit or shorted, corroded connector terminals at sensor probe, broken harness wire flexed during drum vibration.

Locate NTC probe in front air duct. Measure resistance with multimeter (expected 4.8–6.0 kΩ at 25°C, dropping to ~1.2 kΩ at 60°C). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E70

Washing Machine

NTC Temperature Sensor & Thermistor

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Temperature sensor general alarm E70; temperature measurement circuit out of plausible range.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Wash NTC sensor out of tolerance, corroded pins on NTC connector, broken wire in harness, or defective ADC input channel on MCU.

Measure NTC resistance at room temperature 20°C (nominal 4.8–6.0 kΩ; at 60°C ~1.2 kΩ). Clean connector contacts with contact cleaner. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E71

Tumble Dryer

NTC Temperature Sensor & Thermistor

Arthur Martin ADE / ADC Series / Envol Automatique Dryer: Heater duct NTC sensor fault E71; resistance reading out of allowable range (< 500 Ω or > 500 kΩ).

On Arthur Martin (Arthur Martin ADE / ADC Series / Envol Automatique Dryer) models: Thermal shock damage to NTC thermistor bead located on heater casing, melted wiring insulation touching metal chassis, or loose molex plug.

Disconnect sensor plug at rear heater block. Measure resistance across pins (~5.0 kΩ at 25°C). Replace rear NTC probe if open or shorted. Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

E71

Washing Machine

NTC Temperature Sensor & Thermistor

Arthur Martin Electrolux AWF Series / Silence Plus Washer: Wash NTC thermistor open or short circuit E71; voltage signal < 0.1V or > 4.9V DC.

On Arthur Martin (Arthur Martin Electrolux AWF Series / Silence Plus Washer) models: Internal open circuit or short in NTC thermistor pellet, cut sensor wire in tub harness, or water ingress inside NTC casing.

Measure NTC resistance directly across sensor pins (normal 4.8–6.0 kΩ at 20°C; if 0 Ω replace shorted sensor, if infinite ∞ Ω replace open sensor). Hold Départ/Pause and Option buttons firmly for 5 seconds until the red indicator extinguishes and service memory resets.

← Previous PagePage 3 of 7 (191 results)Next Page →

Arthur Martin — Complete Error Code Catalog

167 Verified Error Codes

Server-side index of all verified manufacturer error codes for technicians and automated crawlers.

Dishwasher45

AL5 AL6 C1 C2 C3 i5A i5B i5C i5D i5E i5F i10 i11 i20 i22 i23 i24 i30 i40 i41 i43 i44 i50 i51 i52 i53 i54 i55 i56 i57 i58 i59 i60 i61 i63 i64 i70 i80 i90 iA0 iB0 iC0 iD0 iF0 iF1

Washing Machine57

C9 CF E3A E5A E5C E5D E5E E5F E5H E6H E9C E9E E10 E11 E12 E13 E20 E21 E22 E23 E24 E25 E33 E34 E35 E38 E40 E41 E42 E43 E44 E45 E66 E68 E69 E74 E82 E83 E84 E85 E94 E95 E97 E98 EA0 EA1 EA6 EB0 EF0 EF1 EF2 EF3 EF4 EF5 EH1 EH2 EH3

Tumble Dryer25

E30 E31 E32 E50 E51 E52 E53 E54 E57 E58 E59 E60 E61 E62 E63 E70 E71 E72 E73 E80 E90 E91 E92 E93 EH0

Oven / Microwave12

F101 F102 F103 F104 F105 F106 F107 F108 F109 F110 F111 F112

Hob / Cooktop12

E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA F

Refrigerator / Freezer16

E01 E02 E03 E04 E05 E06 E07 F1 F2 F3 F4 F5 F6 F7 SY EF 5Y EF

Need Help? Call a Certified Technician

Our official certified partners service Arthur Martin appliances in your area.

Electroassistance (Switzerland)Appliance Care UK (United Kingdom)

CodesErreur.com

Premium appliance diagnostics & repair database.
Powered by AI to help certified technicians worldwide.

Trusted by professionals in CH & FR

Platform

Search Database PRO Diagnostic AIPRO Diagnostic Tools Brands

Workshop Tools

Brands (87)OEM Manuals Find Rating Plate Parts Locator

For Technicians

Specialists Technician Forum Tech Jobs Premium

Corporate

Terms of Service Privacy PolicyOfficial Swiss Repair Partner: Electroassistance

OPERATIONAL SAFETY SPECIFICATION

SAFETY DISCLAIMER

The technical information, diagnostic guides, error codes, and AI-generated suggestions provided on this website are intended exclusively for certified and qualified professionals. Appliance repair involves severe electrical hazards, high voltages, and mechanical risks that can result in fatal injury or severe property damage. If you are not a trained technician, do not attempt to repair any appliances. CodesErreur assumes no responsibility or liability for any damage, injury, or consequential losses resulting from the use of the information provided on this platform. You use all information entirely at your own risk.

© 2026 CodesErreur. All rights reserved.

Official Swiss Repair Partner: Electroassistance Terms of Service Privacy Policy