Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Critical freezer high temperature alarm AL01; freezer compartment temperature has risen above safe threshold of -9°C.
Compressor Motor Windings (Run/Start) & Defrost Heater
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Water dispenser filter expiration / flow timeout alarm AL02; water purification filter cartridge life limit or fill slow rate detected.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Water filling timeout alarm AL05; wash tank does not fill to operating level within program timeout limit.
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Interface display communication error E0; temperature control panel loses serial link with master power PCB.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Water fill solenoid valve circuit fault E01; power board detects open circuit across inlet solenoid coil.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Door interlock error E01; appliance refuses to commence wash cycle because the door latch contact is not verified.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Water inlet fill failure E1; appliance detects no incoming water flow into sump after opening fill valve.
Haier I-Move Series / Multi Switch Precision Induction Hob: Touch sensor zone covered by object or liquid E1; continuous conductive activation detected on control glass for >10 seconds.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Refrigerator compartment temperature sensor fault E1; fresh food section thermistor circuit open or shorted.
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Fill meter pulse count error E02; turbine sensor signals water fill but pulse frequency is erratic or dropping out.
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Process air duct NTC sensor error E02; thermistor signal indicates circuit open, short, or temperature out of operating range.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Water inlet fill timeout E02; tub does not reach the minimum operating water level within 210 seconds of valve energization.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Haier I-Move Series / Multi Switch Precision Induction Hob: Induction cooking zone coil overheat E2; NTC temperature sensor beneath ceramic glass detects temperature exceeding 240°C.
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Freezer compartment temperature sensor malfunction E2; low-temperature NTC thermistor circuit open or short-circuited.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Door / lid lock failure E2; machine does not engage lock solenoid or detects door open during cycle start.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Maximum drying cycle time exceeded E03; machine aborts cycle after running for 210 minutes without laundry reaching target dryness.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Water evacuation fault E03; machine aborts cycle with water remaining in drum after 180 seconds of drain pump operation.
Haier I-Move Series / Multi Switch Precision Induction Hob: Induction power board IGBT heatsink overtemperature E3; power transistor heatsink temperature exceeds 95°C safety shutoff.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Evaporator defrost temperature sensor fault E3; defrost termination NTC thermistor out of calibrated ohmic range.
Compressor Motor Windings (Run/Start) & Defrost Heater
Haier I-Move Series / Multi Switch Precision Induction Hob: Induction coil temperature sensor circuit fault E4; coil center NTC thermistor reads open circuit or shorted.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Water fill timeout E4; water does not reach target level within 8 minutes of starting fill cycle.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Water temperature sensor measurement anomaly E05; NTC probe signal resistance indicates temperature below -5°C or above 90°C.
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Drum motor drive failure E06; motor hums but fails to rotate the drum, or drive motor trips on thermal overload.
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Humidity sensor communication error E6; crisper drawer moisture and relative humidity module signal loss.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Drum rotation sensor speed feedback missing E07; controller does not detect drum movement during program run.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Motor drive tachometer fault E07; drum does not rotate or motor starts at uncontrolled high speed then immediately stops.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Wash circulation pump failure E7; motor does not rotate, tachometer feedback is absent, or run capacitor is open.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Move Series / Multi Switch Precision Induction Hob: Cooling fan failure E7; internal induction generator cooling fan motor stalled, disconnected, or zero RPM feedback.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Automatic ice maker mold temperature sensor error E7; ice tray thermistor reading out of bounds during freezing cycle.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Motor drive inverter module overcurrent E7; drive electronics trip on thermal overload or excessive current draw.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Flow-through heater circuit open E08; water temperature does not increase during heated wash stage.
Immersion / Air Heating Element & Klixon Thermostat
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Automatic ice maker ejection motor stall E8; ice tray harvest mechanism fails to complete home position cycle within 3 minutes.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Drum motor drive semiconductor failure E09; motor triac shorted or direction reversing relay contacts burned on control PCB.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Motor drive electronic fault E09; power board detects shorted motor triac or inverter IGBT phase breakdown.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Move Series / Multi Switch Precision Induction Hob: Internal bus communication failure E9; touch control panel loses data communication with induction power module.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: High temperature warming warning E9; fresh food compartment temperature exceeds +12°C continuously for over 2 hours.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Moisture sensing conductivity circuit error E10; sensor bars in door opening read open circuit or shorted to chassis ground.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Program selector / drum position sensor error E10; dial input signal unrecognized or top-loader drum positioning sensor missing.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Exhaust air temperature overheat E11; air temperature leaving the drum exceeds 80°C triggering thermal protection.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Washer-dryer drying heating fault E11; air heating duct fails to reach temperature or dryer thermistor open circuit.
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Serial communication timeout E12; display console fails to exchange data telegrams with main chassis power board.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Washer-dryer ventilation error E12; air circulation blower motor stall or drying auxiliary controller communication loss.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Bus communication fault E13; user interface display panel loses serial handshake with main chassis power board.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Flowmeter signal missing during fill E14; pressure switch senses water rising in tub but zero flowmeter impulses arrive at PCB.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Condensate lift pump motor fault E14; pump fails to lift water from bottom collector to upper reservoir.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Wash water heating failure E14; water temperature does not rise after 20 minutes of active wash program operation.
Immersion / Air Heating Element & Klixon Thermostat
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Microcontroller memory failure E15; main control module detects an invalid EEPROM checksum or unconfigured firmware parameter.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Water softener regeneration valve fault E16; salt chamber regeneration solenoid open-circuit or shorted on power board.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Heating element earth insulation leak E16; appliance trips residual current device (RCD / breaker) or detects stray current to chassis ground.
Immersion / Air Heating Element & Klixon Thermostat
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Motor speed signal frequency anomaly E17; tachometer pulse cadence does not match inverter drive excitation frequency.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Power supply voltage or frequency fault E18; AC mains input deviates outside allowable 190V–255V operating window.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: AC mains power supply out of limits E18; voltage fluctuates outside 185V–260V AC or frequency deviates from 50/60 Hz.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Electronic pressure sensor calibration fault E20; signal frequency received from the analog pressure transducer is out of valid bounds.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Water level sensor drift E21; water column pressure rises unexpectedly while solenoid inlet valves are de-energized.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Siphoning drain detection E22; water level drops continuously during active wash fill cycle without pump activation.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Defrost heating circuit failure Ed; evaporator defrost heater fails to terminate cycle within programmed maximum runtime.
Compressor Motor Windings (Run/Start) & Defrost Heater
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Evaporator fan rotor stall / hardware trip EF; fan motor overcurrent detected by motor driver circuitry.
Compressor Motor Windings (Run/Start) & Defrost Heater
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: Cavity overtemperature condition Er03; cavity temperature exceeds 320°C in standard baking or 520°C in pyrolytic clean mode.
Immersion / Air Heating Element & Klixon Thermostat
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: Pyrolysis door lock latch failure Er05; motorized latch mechanism fails to engage door interlock within 60 seconds of cycle start.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: Power relay board communication lost Er08; display interface loses serial handshake with heating element relay power module.
Immersion / Air Heating Element & Klixon Thermostat
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: Low-voltage DC power supply ripple fault Er21; 5V DC or 12V DC power bus voltage drops below operating threshold.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Haier I-Move Series / Multi Switch Precision Induction Hob: Touch control evaluation hardware fault ER22; capacitive sensing integrated circuit detects an internal analog front-end failure.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Haier I-Move Series / Multi Switch Precision Induction Hob: Power board configuration data corrupted ER31; generator module variant coding table does not match cooktop model setup.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: Display console temperature sensor fault Er36; on-board thermistor on user interface board reads out of range.
Haier I-Move Series / Multi Switch Precision Induction Hob: Touch board ambient NTC sensor shorted ER36; temperature sensor on user interface PCB reads short-circuit to ground.
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: LIN-bus communication error Er47; internal local interconnect network link between touch interface and power module drops packets.
Immersion / Air Heating Element & Klixon Thermostat
Haier I-Move Series / Multi Switch Precision Induction Hob: LIN-Bus communication between touch controller and power inverter module missing ER47; transmission timeout error.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Move Series / Multi Switch Precision Induction Hob: Cooking coil temperature sensor disconnected F0; generator board detects open circuit on temperature feedback line.
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: User interface board communication failure F0; display module cannot communicate with main power relay board.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Variable frequency inverter compressor communication fault F0; main control PCB loses PWM / UART handshake with inverter driver board.
Compressor Motor Windings (Run/Start) & Defrost Heater
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Air intake temperature sensor fault F1; front air temperature probe disconnected or reading outside allowable bounds.
Haier I-Move Series / Multi Switch Precision Induction Hob: Cooking coil temperature sensor short circuit F1; measured probe resistance drops to near zero ohms.
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Freezer evaporator fan motor malfunction F1; low-voltage brushless DC circulation fan stalled or tachometer feedback missing.
Compressor Motor Windings (Run/Start) & Defrost Heater
Haier I-Move Series / Multi Switch Precision Induction Hob: Communication loss to induction generator module F2; main controller loses sync with left or right power inverter board.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Refrigerator compartment air circulation fan fault F2; fresh food multi-airflow fan fails rotation speed verification.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: Temperature sensor probe circuit open F3; sensor signal resistance is infinite, halting heating cycle.
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Condenser cooling fan motor failure F3; rear machine compartment fan stalls or fails thermal heat extraction.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Condensate evacuation pump failure F4; water level switch in collection sump remains active after pump run cycle.
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: Temperature sensor probe short circuit F4; sensor signal resistance is near zero ohms, preventing temperature control.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Heating circuit failure F4; water does not heat up during wash phase within allotted cycle time.
Immersion / Air Heating Element & Klixon Thermostat
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Motor / compressor inverter communication timeout F5; main PCB loses data link with drive inverter module.
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: Cooling fan hall sensor feedback missing F5; electronics cooling fan is commanded on but speed sensor sends zero RPM.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Motorized air damper baffle malfunction F5; motorized cold air shutter fails to reach calibrated open or closed position.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Auxiliary heat-pump cooling fan fault F6; compressor compartment ventilation fan motor stalled or disconnected.
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Refrigerant switching valve error F6; bistable 3-way solenoid valve fails to direct refrigerant between fridge and freezer circuits.
Haier I-Move Series / Multi Switch Precision Induction Hob: Mains supply frequency out of limits F7; AC power line frequency falls outside 47 Hz–63 Hz operating window.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Motor drive board communication / synchronization fault F7; inverter driver board fails to command motor rotation.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Move Series / Multi Switch Precision Induction Hob: Continuous heating safety timer shutoff F8; cooking zone automatically powers off after exceeding maximum continuous runtime limit.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: Meat probe temperature limit exceeded F8; core probe signal indicates temperature above maximum safe reading.
Immersion / Air Heating Element & Klixon Thermostat
Haier I-Move Series / Multi Switch Precision Induction Hob: Induction coil current sensor calibration failure F9; current transformer sensing circuit fails zero-offset balance test at power up.
Immersion / Air Heating Element & Klixon Thermostat
Haier Series 4 / 6 Chef@Home & I-Message Connected Oven: Motorized door latch switch timing error F9; latch motor runs but lock switch does not transition within expected time window.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Water level frequency sensor abnormal FA; water level reading absent or outside valid frequency bounds (~20–40 kHz).
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Inverter drive communication loss FC0; main control module loses communication handshake with motor inverter module.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Display board communication timeout FC1; user interface touch panel fails to synchronize with system controller.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: EEPROM variant configuration parameter mismatch FC2; model code programming does not match installed chassis hardware.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Haier I-Move Series / Multi Switch Precision Induction Hob: Mains supply undervoltage / phase missing alert U; cooktop detects open circuit on secondary phase or voltage under 170V AC.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Anti-flood safety trigger E04; electronic controller detects excessive water column level or floor leak sensor switch closure.
On Haier washing machines powered by Direct Motion beltless electromagnetic direct-drive motor, ABT antibacterial zinc gasket, and Smart Dual Spray: Leaking tub gasket, blocked pressure switch air bell tube, or triac short energizing inlet valve continuously.
Isolate water supply. Inspect base pan for leakage. Detach pressure switch hose and clear chamber sludge. Check valve triac voltage with a multimeter (230V AC). Power on, turn knob to Spin cycle, hold Delay and Temp buttons together for 5 seconds until 'tSt' or drum calibrates, then power off.
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Anti-flood leak protection triggered E4; float switch in the bottom chassis pan rises and engages emergency drain.
On Haier dishwashers featuring I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Leaking sump seal, split recirculation pump casing, door perimeter gasket wear, or cracked fill hose connection.
Disconnect mains power. Sponge out water from bottom collection tray. Inspect sump gasket, pump hose clamps, and tub seams with dry paper. Test anti-flood microswitch continuity with a multimeter. Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.
Haier I-Move Series / Multi Switch Precision Induction Hob: Induction coil temperature sensor circuit fault E4; coil center NTC thermistor reads open circuit or shorted.
On Haier cooktops powered by I-Move Series / Multi Switch induction power board, high-frequency coil induction, and capacitive sensor glass interface: Open or shorted coil center thermistor (~100 kΩ at 25°C), disconnected spade connector on generator board, or pinched wire.
Isolate mains power. Remove glass top. Disconnect coil sensor plug and measure resistance (~100 kΩ at 25°C). Replace sensor assembly if open or short. Wipe glass surface clean, disconnect power supply circuit breaker for 60 seconds, reconnect and hold Pause/Lock key for 5 seconds.
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Ambient room temperature sensor error E4; external cabinet thermistor circuit disconnected or shorted.
On Haier refrigeration units featuring Fresher Shield Total No-Frost inverter cooling, multi-airflow tower, and ABT antibacterial preservation system: Dislodged ambient sensor bead behind top hinge cover or damaged wiring during installation.
Access ambient sensor located in upper hinge cover or rear vent. Verify 5 kΩ at 25°C. Check wiring continuity to main PCB connector. Reset: Press and hold Fridge Temp and Freezer Temp keys together for 6 seconds until long beep confirms electronic board reset.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Water fill timeout E4; water does not reach target level within 8 minutes of starting fill cycle.
On Haier washers utilizing Direct Motion beltless electromagnetic direct-drive motor, ABT antibacterial zinc gasket, and Smart Dual Spray: Low water supply pressure, closed supply shutoff valve, clogged hose inlet filter, or defective water valve coil (~3.5–4.5 kΩ).
Verify water tap is fully open and supply pressure is adequate. Unscrew hose and rinse clean filter mesh. Measure valve coil (~3.5–4.5 kΩ). Power on, turn knob to Spin cycle, hold Delay and Temp buttons together for 5 seconds until 'tSt' or drum calibrates, then power off.
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Water temperature sensor measurement anomaly E05; NTC probe signal resistance indicates temperature below -5°C or above 90°C.
On Haier dishwashers powered by I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Detergent residue film insulating thermistor head in sump, cracked thermistor bead, or moisture in wiring connector.
Unplug NTC sensor from sump housing. Clean stainless sensing face with vinegar/descaler. Measure resistance at room temperature (~47 kΩ at 25°C). Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Heat pump compressor thermistor fault E05; suction / discharge pipe NTC sensor value out of operational specifications.
On Haier tumble dryers utilizing I-Pro Series Dual Inverter heat-pump circuit, sensor-dry thermistor array, and reverse-tumble motor control: Open or shorted pipe-clip NTC thermistor (~10.0 kΩ at 25°C), wire pulled from sensor body, or connector corrosion.
Locate compressor discharge and suction pipe sensors. Disconnect plug and measure thermistor resistance (~10.0 kΩ at 25°C). Replace clip sensor if out of spec. Turn dial to Warm Air program, press Dry Level and Time Dry together for 5 seconds until beep sounds, then return to Power Off.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Wash temperature NTC sensor fault E05; electronic module reads temperature values outside nominal limits (-10°C to +105°C).
On Haier washing machines featuring Direct Motion beltless electromagnetic direct-drive motor, ABT antibacterial zinc gasket, and Smart Dual Spray: Open or shorted NTC thermistor probe, loose wiring terminals at heating element base, or moisture ingress.
Disconnect sensor plug. Measure NTC resistance across probe pins (nominal ~20.0 kΩ at 25°C, dropping to ~2.5 kΩ at 60°C). Replace if defective. Power on, turn knob to Spin cycle, hold Delay and Temp buttons together for 5 seconds until 'tSt' or drum calibrates, then power off.
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Wash water temperature NTC sensor error E5; thermistor reading open-circuit or short-circuit outside allowable range.
On Haier dishwashers powered by I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Defective NTC thermistor bead in sump, corroded connector terminals from detergent seepage, or damaged wiring harness.
Disconnect NTC connector at sump. Measure thermistor resistance (nominal ~47 kΩ at 25°C or ~10 kΩ depending on platform). Replace probe if open. Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.
Electronic Control Board (PCB) & Bus Communications
Haier I-Move Series / Multi Switch Precision Induction Hob: Mains supply overvoltage fault E5; input AC voltage exceeds safe operating limit (>275V AC).
On Haier cooktops utilizing I-Move Series / Multi Switch induction power board, high-frequency coil induction, and capacitive sensor glass interface: Incorrect 400V connection without neutral, floating neutral line in household breaker panel, or electrical storm surge.
Immediately turn off circuit breaker. Measure voltage between Live (L1/L2) and Neutral (N) at terminal block (must be 230V AC; if ~400V AC, neutral is missing). Wipe glass surface clean, disconnect power supply circuit breaker for 60 seconds, reconnect and hold Pause/Lock key for 5 seconds.
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Convertible zone temperature sensor fault E5; MyZone / Flex drawer thermistor sensing circuit failed.
On Haier refrigeration units featuring Fresher Shield Total No-Frost inverter cooling, multi-airflow tower, and ABT antibacterial preservation system: Drawer slide mechanical abrasion against sensor cable, condensation in sensor pocket, or open thermistor.
Remove convertible drawer and inspect NTC harness behind air duct. Measure ~5 kΩ at 25°C and ~16 kΩ at 0°C. Replace damaged sensor loom. Reset: Press and hold Fridge Temp and Freezer Temp keys together for 6 seconds until long beep confirms electronic board reset.
On Haier dishwashers featuring I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Mains voltage surge damage to microcomputer memory cells, power supply capacitor failure, or unprogrammed module.
Perform hard power reset for 10 minutes. If error returns, access service menu to enter model programming code or install pre-configured PCB. Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Drum motor drive failure E06; motor hums but fails to rotate the drum, or drive motor trips on thermal overload.
On Haier tumble dryers powered by I-Pro Series Dual Inverter heat-pump circuit, sensor-dry thermistor array, and reverse-tumble motor control: Open motor run capacitor (~8–10 µF), seized drum support roller bearing, open stator winding (~20–35 Ω), or belt jam.
Check drum free rotation by hand. Discharge and test motor capacitor with capacitance meter (~8–10 µF nominal). Measure motor winding resistance (~20–35 Ω). Turn dial to Warm Air program, press Dry Level and Time Dry together for 5 seconds until beep sounds, then return to Power Off.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Drum unbalance / microcomputer checksum error E06; spin ramp aborts repeatedly or main PCB parameter memory fails verification.
On Haier washing machines utilizing Direct Motion beltless electromagnetic direct-drive motor, ABT antibacterial zinc gasket, and Smart Dual Spray: Tangled heavy blanket causing asymmetric mass, worn drum shock absorbers, or corrupted EEPROM data sector on board.
Redistribute wet garments evenly in drum. Inspect shock absorbers and suspension springs for damping resistance. Re-flash or replace module if code persists empty. Power on, turn knob to Spin cycle, hold Delay and Temp buttons together for 5 seconds until 'tSt' or drum calibrates, then power off.
On Haier dishwashers utilizing I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: AC mains voltage spike, corrupted non-volatile memory cell on PCB, or unprogrammed replacement board installed.
Power down machine at isolation switch for 10 minutes. If error persists, enter service mode and re-enter model code, or replace main control board. Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.
Electronic Control Board (PCB) & Bus Communications
Haier I-Move Series / Multi Switch Precision Induction Hob: Mains supply undervoltage fault E6; input AC voltage drops below operational threshold (<170V AC).
On Haier cooktops featuring I-Move Series / Multi Switch induction power board, high-frequency coil induction, and capacitive sensor glass interface: Heavy grid brownout, loose electrical terminal screws on terminal block, or undersized supply wiring causing voltage sag.
Check input AC voltage under load with digital voltmeter. Tighten all phase and neutral terminal screws on rear junction block. Wipe glass surface clean, disconnect power supply circuit breaker for 60 seconds, reconnect and hold Pause/Lock key for 5 seconds.
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Humidity sensor communication error E6; crisper drawer moisture and relative humidity module signal loss.
On Haier refrigeration units featuring Fresher Shield Total No-Frost inverter cooling, multi-airflow tower, and ABT antibacterial preservation system: Liquid spillage into crisper sensor housing, oxidized I2C bus contacts, or failed humidity IC module.
Inspect humidity sensor PCB in vegetable crisper. Clean connector with contact cleaner; verify 5V DC supply rail. Replace module if unresponsive. Reset: Press and hold Fridge Temp and Freezer Temp keys together for 6 seconds until long beep confirms electronic board reset.
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Circulation wash pump motor rotation error E07; tachometer sensor sends no pulse feedback to power inverter.
On Haier dishwashers powered by I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Jammed circulation pump rotor, detached tachometer coil or magnet, or open stator winding phase (~45–95 Ω).
Inspect circulation pump volute chamber for foreign obstructions. Measure stator windings resistance (~45–95 Ω across phases). Verify tach coil (~100–180 Ω). Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Drum rotation sensor speed feedback missing E07; controller does not detect drum movement during program run.
On Haier tumble dryers utilizing I-Pro Series Dual Inverter heat-pump circuit, sensor-dry thermistor array, and reverse-tumble motor control: Broken drum drive belt, dislodged tachometer magnet on motor rear, or open optical/Hall rotation sensor.
Open top cover and inspect if poly-V belt is intact around drum. Check rear motor shaft magnet and test tachometer coil resistance (~110–180 Ω) with a multimeter. Replace belt if snapped. Turn dial to Warm Air program, press Dry Level and Time Dry together for 5 seconds until beep sounds, then return to Power Off.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Motor drive tachometer fault E07; drum does not rotate or motor starts at uncontrolled high speed then immediately stops.
On Haier washing machines powered by Direct Motion beltless electromagnetic direct-drive motor, ABT antibacterial zinc gasket, and Smart Dual Spray: Dislodged magnetic ring on motor tail shaft, open tachometer coil (~115–180 Ω), or 3-phase BLDC winding open (~5–12 Ω).
Verify tachometer magnet is seated tight on rotor. Measure tach coil resistance (~115–180 Ω) or BLDC phase resistance (~5–12 Ω between all 3 phases). Power on, turn knob to Spin cycle, hold Delay and Temp buttons together for 5 seconds until 'tSt' or drum calibrates, then power off.
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Wash circulation pump failure E7; motor does not rotate, tachometer feedback is absent, or run capacitor is open.
On Haier dishwashers featuring I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Calcium scale or fruit seed jamming pump volute, open main winding (~45–95 Ω), or defective BLDC inverter driver.
Inspect circulation pump volute for debris. Spin rotor with screwdriver to ensure free turning. Measure motor winding resistance (~45–95 Ω). Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.
Haier I-Move Series / Multi Switch Precision Induction Hob: Cooling fan failure E7; internal induction generator cooling fan motor stalled, disconnected, or zero RPM feedback.
On Haier cooktops powered by I-Move Series / Multi Switch induction power board, high-frequency coil induction, and capacitive sensor glass interface: Cable tie or debris trapped in fan blade assembly, disconnected 12V DC 3-wire plug, or open fan motor winding.
Remove glass surface. Spin cooling fan impeller to check for free turning. Verify 12V DC supply on fan connector. Replace fan assembly if motor is open. Wipe glass surface clean, disconnect power supply circuit breaker for 60 seconds, reconnect and hold Pause/Lock key for 5 seconds.
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Automatic ice maker mold temperature sensor error E7; ice tray thermistor reading out of bounds during freezing cycle.
On Haier refrigeration units featuring Fresher Shield Total No-Frost inverter cooling, multi-airflow tower, and ABT antibacterial preservation system: Wire harness fatigue from ice maker harvest rotation, iced connector pin, or failed mold sensor.
Measure ice mold sensor resistance: ~5 kΩ at 25°C, ~32 kΩ at -15°C. Check twisting harness bundle for severed copper cores. Replace ice maker head if open. Reset: Press and hold Fridge Temp and Freezer Temp keys together for 6 seconds until long beep confirms electronic board reset.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Motor drive inverter module overcurrent E7; drive electronics trip on thermal overload or excessive current draw.
On Haier washers utilizing Direct Motion beltless electromagnetic direct-drive motor, ABT antibacterial zinc gasket, and Smart Dual Spray: Mechanical drum binding, motor bearing failure, shorted BLDC stator phase, or failed IPM power semiconductor bridge.
Rotate drum by hand to verify smooth movement. Disconnect motor harness and measure phase-to-phase resistance (~5–12 Ω balanced across U-V-W). Power on, turn knob to Spin cycle, hold Delay and Temp buttons together for 5 seconds until 'tSt' or drum calibrates, then power off.
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Flow-through heater circuit open E08; water temperature does not increase during heated wash stage.
On Haier dishwashers powered by I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Open heater element element (~25–32 Ω), tripped non-resettable thermal fuse, or desoldered relay pin on PCB.
Measure element terminal resistance (~25–32 Ω). Check continuity through integrated thermal cutoff fuses. Verify solder joints of heater relay on control PCB. Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.
Haier I-Pro Series 7 / 9 Dual Inverter Heat Pump Dryer: Rear heater safety Klixon thermostat open E08; high-limit thermal switch interrupts power to heater assembly.
On Haier tumble dryers powered by I-Pro Series Dual Inverter heat-pump circuit, sensor-dry thermistor array, and reverse-tumble motor control: Blocked rear air duct causing excessive heat buildup, stalled blower fan, or fatigued bi-metal disc in thermostat.
Check red reset push-button on rear thermostat body (press to reset). Test continuity across terminals with ohmmeter (must be 0 Ω). Clean rear duct thoroughly. Turn dial to Warm Air program, press Dry Level and Time Dry together for 5 seconds until beep sounds, then return to Power Off.
Haier I-Pro Series 3 / 5 / 7 Direct Motion Beltless Washer: Motor overspeed burst detected E08; speed feedback frequency spikes abnormally during initial tumble wash sequence.
On Haier washing machines featuring Direct Motion beltless electromagnetic direct-drive motor, ABT antibacterial zinc gasket, and Smart Dual Spray: Cracked tachometer magnet hub slipping on motor shaft, electrical noise on speed sensor lines, or shorted drive triac.
Inspect tachometer magnetic ring for hairline fractures. Re-route sensor wiring away from heater cables. Test motor drive triac for zero-ohm gate short. Power on, turn knob to Spin cycle, hold Delay and Temp buttons together for 5 seconds until 'tSt' or drum calibrates, then power off.
Haier I-Pro Shine / Washlogix Ultra Silence Dishwasher: Wash heating circuit failure E8; water fails to heat up, or high-limit safety thermostat opens.
On Haier dishwashers powered by I-Pro Shine Ultra Silence brushless wash circulation pump, dual-zone inverter spray system, and micro-filtration: Open flow-through tubular heating element (~25–32 Ω), burned heater relay contacts on board, or tripped Klixon thermal limiter.
Disconnect heater leads. Measure element resistance (~25–32 Ω across terminals). Test continuity of series safety thermostat. Check solder joints on PCB relay. Press Power button off, hold Half Load and Start buttons together while powering on until diagnostic test mode 01 displays, then power off.
Electronic Control Board (PCB) & Bus Communications
Haier I-Move Series / Multi Switch Precision Induction Hob: Pan detection circuit error E8; coil cannot establish electromagnetic coupling or detects non-ferrous cookware.
On Haier cooktops utilizing I-Move Series / Multi Switch induction power board, high-frequency coil induction, and capacitive sensor glass interface: Aluminum, glass, or non-magnetic copper pan, pan base diameter too small for zone (<12 cm), or current transformer circuit drift.
Test cookware base with a refrigerator magnet (must firmly stick). Ensure pan base covers at least 60% of cooking zone diameter. Wipe glass surface clean, disconnect power supply circuit breaker for 60 seconds, reconnect and hold Pause/Lock key for 5 seconds.
Haier Cube 90 / FD 70 / 3D & 4D Total No Frost Refrigerator: Automatic ice maker ejection motor stall E8; ice tray harvest mechanism fails to complete home position cycle within 3 minutes.
On Haier refrigeration units featuring Fresher Shield Total No-Frost inverter cooling, multi-airflow tower, and ABT antibacterial preservation system: Ice bridge jamming the harvest tray, stripped reduction gear teeth, or defective microswitch contact.
Inspect ice tray for frozen obstruction. Test harvest motor winding resistance (~200-400 Ω) and verify 12V DC drive pulse. Verify microswitch continuity in home position. Reset: Press and hold Fridge Temp and Freezer Temp keys together for 6 seconds until long beep confirms electronic board reset.