Access our premium database of error codes, common faults, and professional repair solutions for FAGOR appliances.
High temperature alarm in refrigerator
The refrigerator door has been left open, a large amount of warm food was added, or there is a cooling system fault.
Ensure the door is fully closed and the seal is intact. Allow time for the temperature to stabilize. If alarm persists, check for cooling issues.
High temperature alarm in freezer
The freezer door has been left open, a large amount of unfrozen food was added, or there is a cooling system fault.
Check that the door is sealed properly. Avoid opening the door frequently. If the temperature doesn't drop, service is needed.
FAGOR AL03: Door lock safety interlock fault in Refrigerator / Freezer; door switch contact fails to close or open.
The refrigerator or freezer door has been open for an extended period (usually over 1-2 minutes).
Close the door. If the alarm continues with the door closed, the door switch may be faulty.
Door error during cooking
The door lock status changed unexpectedly during a cooking cycle, or the door switch is faulty.
Cancel the program, ensure the door is closed properly, and restart. If it persists, the door switch or lock may need service.
FAGOR D01: Water inlet / filling timeout in Washing Machine; appliance fails to fill to minimum operational level.
Low water pressure, closed water tap, or kinked inlet hose.
Check that the water supply tap is fully open and that the inlet hose is straight.
FAGOR D02: Water drainage failure detected in Washing Machine; drain pump cannot evacuate water within safety time limit.
Drain filter or hose is blocked.
Clean the pump filter located at the bottom front of the machine. Ensure the drain hose is not blocked.
FAGOR D07: Door lock safety interlock fault in Washing Machine; door switch contact fails to close or open.
The door is not correctly closed or the lock mechanism is faulty.
Open the door and close it again firmly. If the error code remains, the door interlock may need replacing.
Control board communication error
A communication fault has occurred between the main control board and other components.
Reset the machine by turning it off at the mains for 5 minutes. If it reoccurs, a service call is needed.
Temperature issue in the refrigerator compartment.
The refrigerator temperature sensor (thermistor) has failed (open or short circuit).
Test the sensor's resistance. If the reading is incorrect for the current temperature, replace the sensor.
FAGOR E2: NTC temperature sensor signal out of range (open or short circuit) in Hob / Cooktop.
A temperature sensor within the hob electronics has detected an over-temperature condition or has failed.
Let the hob cool down. If the error reappears on a cold hob, the sensor or control board needs service.
FAGOR E04: Water level pressure sensor/switch frequency anomaly detected in Washing Machine.
The pressure switch has detected too much water in the drum, possibly from a stuck inlet valve.
Turn off the appliance and the water supply. The fault is likely with the pressure switch or water inlet valve and requires a technician.
Defrost system failure; excessive frost buildup.
The defrost heater, thermal fuse, or control board has failed, preventing the appliance from running a defrost cycle.
Manually defrost the unit. Test the defrost heater and thermal fuse for continuity and replace if either is open circuit.
FAGOR E5: Operational cycle fault detected during Hob / Cooktop program execution.
Faulty connection or communication failure between the user interface and the induction power module.
Reset power to the hob at the circuit breaker for 5 minutes. If the error persists, a service technician is required.
Induction coil sensor error
The sensor associated with one of the induction coils has failed.
This is an internal hardware fault that requires professional repair.
Water fill timeout exceeded with insufficient water entering the appliance.
Closed water supply tap, kinked or clogged inlet hose filter screen, or open coil on the solenoid water inlet valve.
Ensure the water tap is fully open. Check the inlet hose for kinks or blockages. Test and replace the water inlet valve if necessary.
FAGOR F1: NTC temperature sensor signal out of range (open or short circuit) in Refrigerator / Freezer.
The temperature sensor (NTC) in the freezer compartment is faulty or disconnected.
A technician needs to access the sensor to check its wiring and resistance, and replace it if necessary.
Draining problem / Water not emptying
The drain filter is clogged, the drain hose is blocked or kinked, or the drain pump is faulty.
Disconnect from power. Clean the drain pump filter. Check the drain hose for obstructions. Inspect the drain pump impeller.
Refrigerator sensor fault
The temperature sensor (NTC) in the fresh food compartment is faulty or disconnected.
The sensor's wiring and resistance need to be checked. It likely needs to be replaced.
FAGOR F03: NTC temperature sensor signal out of range (open or short circuit) in Washing Machine.
The heating element has failed, or there is an issue with the NTC temperature sensor or its wiring.
Requires a technician to test the continuity of the heating element and the resistance of the NTC sensor.
FAGOR F3: Cooling circuit or defrost system anomaly in Refrigerator / Freezer; compartment temperature deviation.
The sensor attached to the evaporator coil, which monitors defrost cycles, has failed.
This sensor is located inside the appliance panels and requires a service technician to replace.
FAGOR F04: Door lock safety interlock fault in Washing Machine; door switch contact fails to close or open.
The door is not closed properly, or the door lock mechanism has failed.
Ensure the door is closed firmly. If the error persists, the door lock assembly may need to be replaced.
FAGOR F4: Cooling circuit or defrost system anomaly in Refrigerator / Freezer; compartment temperature deviation.
The heating element that melts ice off the evaporator coils during a defrost cycle has failed.
This will cause excessive frost buildup and poor cooling. The defrost heater needs to be tested and replaced.
Temperature sensor (NTC) error
The NTC temperature sensor is faulty, or its wiring is disconnected or damaged.
Check the wiring to the NTC sensor. Test the sensor's resistance; it should change with temperature. Replace if faulty.
FAGOR F5: Motor drive or inverter rotation anomaly in Refrigerator / Freezer; drum/motor fails to spin at target RPM.
The motorized damper controlling airflow between the freezer and refrigerator is stuck or faulty.
The damper assembly needs to be inspected for ice obstruction or mechanical failure and may need replacement.
Motor fault (Tachometer sensor)
The motor's tachometer generator has failed, motor brushes are worn, or there's a wiring issue.
Check the motor connections and carbon brushes. The motor or tacho coil may need replacement.
FAGOR F6: Water inlet / filling timeout in Dishwasher; appliance fails to fill to minimum operational level.
The water tap is not open, the inlet hose is blocked, or the aquastop/inlet valve is faulty.
Check that the water supply is turned on. Inspect the inlet hose for kinks. If the issue persists, the inlet valve may need replacement.
Motor control board (Triac) fault
A component (triac) on the main control board that controls the motor has failed.
The main control board (PCB) will likely need to be repaired or replaced by a qualified technician.
FAGOR F7: Cooling circuit or defrost system anomaly in Refrigerator / Freezer; compartment temperature deviation.
The compressor is not running, or its starting components (relay, capacitor) have failed.
This indicates a major cooling system failure. Check if the compressor is warm or vibrating. Requires a refrigeration technician.
Continuous touch key activation
A liquid spill, food residue, or an object is on the touch control panel, or the panel is faulty.
Turn off the hob. Clean and dry the control panel area thoroughly. Remove any objects from the surface.
FAGOR F09: Operational cycle fault detected during Washing Machine program execution.
The electronic control unit (ECU) has experienced a data corruption or memory failure.
Try a hard reset by unplugging the appliance for 10-15 minutes. If the error returns, the control board needs to be replaced.
Our official certified partners service FAGOR appliances in your area.