Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: High temperature alarm in freezer compartment AL01; internal temperature rises above -9°C and audible buzzer sounds.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Door open warning signal persistent AL02; acoustic door alarm sounds and interior light remains energized with door shut.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Auto-Stop safety timeout triggered AS; all induction cooking zones shut down automatically after liquid spillover or prolonged cooking.
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Water fill timeout d01; appliance fails to fill with adequate water volume within 4 minutes of program launch.
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Condensation water reservoir full d01; dryer halts cycle and triggers acoustic water tank warning.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Fridge compartment temperature sensor failure d01; internal cold air temperature fluctuates uncontrollably.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Water intake timeout d01; tub water level does not reach wash threshold within 6 minutes of valve opening.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Condensate lift pump failure d02; water fails to pump up into collection tank and accumulates in chassis sump base.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Drain pump timeout d02; water remains in the drum after 4 minutes of continuous drain pump operation.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Ambient room temperature sensor error d03; unit cannot adapt cooling cycles to room climate variations.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Heating circuit timeout d03; water temperature fails to increase by more than 2°C within 30 minutes of wash cycle.
Immersion / Air Heating Element & Klixon Thermostat
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Drum motor drive stall d04; drive motor hums loudly or fails to turn the drum loaded with damp laundry.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Evaporator circulation fan motor failure d05; cold air does not circulate into the refrigeration compartments.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Wash motor overcurrent cutoff d06; power electronic controller trips due to excessive electric current draw by the circulation pump.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Motorized air damper flap malfunction d06; fresh food compartment either freezes contents or remains too warm.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Motor tachometer signal fault d06; drum does not rotate or motor starts then immediately stops after speed feedback loss.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Condenser cooling fan motor failure d07; compressor overheats, trips overload protector, and cooling stops.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Door interlock safety fault d07; cycle will not begin because electronic module cannot confirm closed door contact.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Alternating spray distributor valve motor fault d08; wash water does not alternate between upper and lower spray arms.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Inverter compressor drive or communication failure d08; compressor fails to start or rapidly cuts out after clicking.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Drum rotation reversal fault d08; drum rotates only in one direction during wash tumble phases.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Internal control bus communication error d09; display fascia loses synchronism with main hydraulic power board.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Automatic ice maker mechanism failure d09; ice cubes are not ejected into storage bucket or water fill fails.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Continuous uncontrolled water fill d10; water continues entering appliance after target fill level is achieved.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Main electronic control PCB memory error d10; unit resets intermittently or fails to execute temperature programs.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Abnormal heating in rinse cycle d11; water heats unexpectedly during cold water rinse phases.
Immersion / Air Heating Element & Klixon Thermostat
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Residual water detected after pumpout d12; pressure sensor fails to register empty tub state after drain sequence.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Wash pump cavitation / water fill discrepancy d14; circulation motor draws irregular current due to aerated water foam.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Inverter drum motor communication loss d15; variable speed motor controller fails to respond to main microprocessor commands.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Electronic pressure switch frequency fault d15; analog level sensor outputs erratic frequency signal to main PCB.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Door latch open during cycle d16; cycle pauses immediately as door contact microswitch opens during active operation.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Inverter module bus link error d16; main controller loses communication with 3-phase BLDC motor inverter card.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Mains supply frequency out of bounds d18; line frequency deviates outside 47 Hz – 63 Hz operational tolerances.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: User interface display communication timeout d20; display panel loses serial synchronization with main power controller.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Water distributor stepper motor fault d20; water stream cannot be directed to the selected additive compartment.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Display to power board communication loss d21; control panel lights flash or display is completely blank while machine halts.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Washer-dryer ventilation fan failure d24; process air blower fails to spin during drying phase.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Door unlock timeout at cycle completion d27; door remains securely locked after wash program finishes and drum stops.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Touch control panel link failure E1; induction zones flash 'E1' and power sliders do not respond to fingertip touch.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Induction coil temperature sensor fault E2; zone display flashes 'E2' and cuts power to prevent glass overheating.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Mains undervoltage protection trip E4; cooktop shuts down zones because electrical line voltage drops below 180 V RMS.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Electronics cooling fan motor failure E7; cooktop detects stalled or disconnected fan motor during boot diagnostics.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Pan detection resonant circuit fault E8; zone display flashes 'E8' and fails to acknowledge presence of magnetic cookware.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Microcontroller configuration jumper / EEPROM mismatch E9; power board variant coding does not match user interface.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Main power board communication timeout Er06; display module loses digital data exchange with the internal power relay board.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Steam boiler water evacuation fault Er10; drain pump fails to pump residual water out of the steam boiler.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Upper heating grill element relay fault Er11; top grill element glows red continuously without cooking program active.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Circular convection fan heating element open circuit Er13; convection forced air mode blows air without heating.
Immersion / Air Heating Element & Klixon Thermostat
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: No cookware detected or unsuitable pan base F0; zone display alternates 'F0' and heating output is withheld.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Basque electronic platform water fill fault F01; water inlet solenoid valve fails to supply water within allocated timeout.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: User interface keyboard communication timeout F1; touch control panel loses synchronization with induction power board.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Refrigerator compartment air temperature probe failure F2; display alternates temperature and fault code.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Tangential cooling fan speed error F03; fan operates at insufficient RPM or tachometer signal is missing.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: High voltage surge protection active F3; power board shuts down induction frequency generation to prevent semiconductor destruction.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Freezer compartment air temperature probe failure F3; freezer temperature control loses precision and warning flashes.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Pyrolytic latch microswitch position error F05; position feedback microswitch does not toggle when door unlatches.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Evaporator fan motor feedback failure F5; fan motor does not achieve target operating RPM during cooling demand.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Continuous water entry / water level safety fault F6; water continues to rise after program attempts shut-off.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Short-circuited IGBT power semiconductor F6; circuit breaker trips with an audible pop when zone is turned on.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Door display communication fault F6; user interface loses digital connection to the main power board.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Cooling fan blocked or low RPM stall F7; electronic safety cuts zone power when fan fails to achieve operational speed.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Control board EEPROM calibration checksum failure F9; factory power table values are corrupted and zones will not operate.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Inverter module bus link error d16; main controller loses communication with 3-phase BLDC motor inverter card.
On FAGOR washing machines utilizing Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Disconnected serial data harness between boards, blown inverter onboard fuse, or failed IPM driver IC.
Inspect multi-wire data ribbon between main PCB and inverter module. Verify 310V DC bus voltage across inverter bulk electrolytic capacitors. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Top-loading dryer drum positioning fault d17; drum doors fail to orient toward top opening when cycle completes.
On FAGOR top-loading dryers utilizing Innova thermodynamic refrigeration circuit, dual conductivity sensor bars, and reversible drum rotation: Dislodged magnetic sensor pill on drum wheel, defective reed ILS sensor on chassis, or loose cable.
Inspect drum flank for positioning magnet. Pass a test magnet over the reed switch while testing continuity with a multimeter. Turn dial to Off position, hold Start and Anti-Crease buttons together for 6 seconds until buzzer beeps, then turn back on.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Posistop top-loader drum positioning error d17; drum doors fail to halt facing upward at cycle finish.
On FAGOR top-loading washing machines featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Missing or dislodged drum magnet, defective reed sensor (ILS) on tub outer rim, or loose sensor harness.
Inspect drum periphery for presence of positioning magnet. Test reed switch closure with multimeter while passing a magnet over sensor tip. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Maximum drying cycle timeout exceeded d18; machine aborts after running for over 180 minutes without reaching target dry state.
On FAGOR tumble dryers utilizing Innova thermodynamic refrigeration circuit, dual conductivity sensor bars, and reversible drum rotation: Wet overloaded laundry from an unspun washer cycle (<800 RPM), severely blocked condenser, or weak heat pump performance.
Spin clothes in washing machine at 1200+ RPM prior to drying. Wash condenser core thoroughly. Reduce total laundry weight in drum. Turn dial to Off position, hold Start and Anti-Crease buttons together for 6 seconds until buzzer beeps, then turn back on.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Mains supply frequency out of bounds d18; line frequency deviates outside 47 Hz – 63 Hz operational tolerances.
On FAGOR washing machines featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Unstable generator or inverter power source, dirty mains electrical noise, or degraded mains zero-cross detection circuit on PCB.
Verify mains supply frequency with a certified digital multimeter (nominal 50 Hz ±1 Hz). If grid power is clean, replace control module. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Electrical mains frequency error d19; line frequency fluctuates outside the valid 50 Hz / 60 Hz operating window.
On FAGOR tumble dryers utilizing Innova thermodynamic refrigeration circuit, dual conductivity sensor bars, and reversible drum rotation: Unregulated emergency generator or inverter supply, heavy industrial grid noise, or failed zero-cross circuit on PCB.
Measure supply frequency at wall outlet with a digital multimeter (must be 50 Hz ±1 Hz). If grid power is stable, replace control module. Turn dial to Off position, hold Start and Anti-Crease buttons together for 6 seconds until buzzer beeps, then turn back on.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Inverter module heatsink overtemperature d19; motor drive heat sink temperature exceeds 95°C during active wash cycle.
On FAGOR washing machines featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Heavy sustained laundry overloading, blocked internal cabinet ventilation slots, or thermal paste dry-out under IPM.
Allow appliance to cool down for 45 minutes. Reduce laundry load. Clear dust from cabinet ventilation louvers. Renew thermal paste if accessible. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Electronic Control Board (PCB) & Bus Communications
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: User interface display communication timeout d20; display panel loses serial synchronization with main power controller.
On FAGOR tumble dryers utilizing Innova thermodynamic refrigeration circuit, dual conductivity sensor bars, and reversible drum rotation: Loosened edge connector on display board, moisture oxidation on wiring pins, or corrupted display microcontroller.
Inspect wiring harness connecting display to lower chassis power board. Clean edge connectors with electrical contact spray. Measure 5V DC line. Turn dial to Off position, hold Start and Anti-Crease buttons together for 6 seconds until buzzer beeps, then turn back on.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Water distributor stepper motor fault d20; water stream cannot be directed to the selected additive compartment.
On FAGOR washing machines featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Jammed distributor nozzle arm, stripped nylon reduction gear, or open stepper motor phase winding (~150–250 Ω).
Inspect top distributor nozzle mechanism under cover. Clear lime build-up. Measure stepper motor phase resistances (~150–250 Ω per phase). Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Display to power board communication loss d21; control panel lights flash or display is completely blank while machine halts.
On FAGOR washing machines featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Disconnected or pinched multi-core communication cable, oxidized edge terminals, or damaged low-voltage DC power supply.
Check wiring harness continuity between user interface and power board. Measure 5V DC and 12V DC test points on control board. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Washer-dryer drying heating circuit fault d22; air heating duct fails to reach target temperature during drying cycle.
On FAGOR washer-dryers featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Open drying heating element bank (~35–45 Ω), tripped manual reset high-limit Klixon, or stuck drying relay.
Press manual reset button on top of drying duct Klixon. Measure drying heating element resistance (~35–45 Ω). Check circuit continuity. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Condenser drying NTC thermistor fault d23; temperature sensing on the condensation duct fails verification.
On FAGOR washer-dryers featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Open or shorted condenser NTC thermistor probe (~20 kΩ at 20°C, ~5 kΩ at 60°C), or moisture ingress in harness plug.
Disconnect sensor plug on condensation duct. Measure resistance (~20 kΩ at 20°C). Replace NTC sensor probe if reading is open or zero ohms. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Washer-dryer ventilation fan failure d24; process air blower fails to spin during drying phase.
On FAGOR washer-dryers featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Heavy lint accumulation seizing the fan rotor, degraded motor winding (~120–180 Ω), or triac drive failure on PCB.
Dismantle fan volute and clean lint buildup from impeller. Measure fan motor winding resistance (~120–180 Ω). Verify 230V AC arrival on run. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Repetitive unbalance abort d25; machine terminates program before final spin after 15 unsuccessful redistribution attempts.
On FAGOR washing machines featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Heavy waterlogged single garment, broken internal tub shock absorber, or unlevel appliance installation feet.
Redistribute garments manually and re-run spin cycle. Check machine leveling with a spirit level. Inspect friction shock absorbers. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: BLDC motor inverter overcurrent fault d26; peak motor phase current exceeds safe hardware protection threshold.
On FAGOR washing machines featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Mechanical drum obstruction (foreign object between tub and drum), shorted motor stator winding, or failed IGBT bridge.
Rotate drum by hand to confirm free spinning. Measure resistance across all 3 motor phases (nominal ~5–12 Ω balanced). Replace inverter PCB if shorted. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Door unlock timeout at cycle completion d27; door remains securely locked after wash program finishes and drum stops.
On FAGOR washing machines featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Residual water detected by pressure switch, slow-cooling PTC bi-metal pill, or mechanical latch binding against rubber seal.
Wait 3 minutes for PTC to cool. Push firmly on door panel while pulling handle to relieve latch pressure. Inspect drain filter for water buildup. Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Touch control panel link failure E1; induction zones flash 'E1' and power sliders do not respond to fingertip touch.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Loosened ribbon cable connecting capacitive glass touch board to lower induction generator power module.
Disconnect mains breaker. Lift cooktop, unclip touch board ribbon, clean gold contacts with isopropyl alcohol, and reseat firmly. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Induction coil temperature sensor fault E2; zone display flashes 'E2' and cuts power to prevent glass overheating.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Open or shorted spring-loaded center coil NTC thermistor (~100 kΩ at 25°C), or detached silicone thermal boot.
Access coil assembly beneath glass. Measure coil center NTC sensor resistance (~100 kΩ at 25°C, dropping to ~10 kΩ at 80°C). Replace sensor if open. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Mains overvoltage protection trip E3; cooktop disables high-power induction generators when voltage exceeds 265 V RMS.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Neutral wire floating or loose in electrical junction box (causing 400V across phases), or utility grid surge.
Measure phase-to-neutral voltage at terminal block with a certified digital multimeter (nominal 230V AC ±10%). Tighten neutral screw. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Mains undervoltage protection trip E4; cooktop shuts down zones because electrical line voltage drops below 180 V RMS.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Heavy line sagging from undersized installation wiring, high resistance loose terminal connection, or power grid brownout.
Verify electrical line voltage under load (minimum 207V AC). Ensure dedicated 32A 6mm² or two-phase 16A 2.5mm² wiring is installed. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Power generator heatsink overtemperature E5; cooktop throttles or halts cooking because aluminum heatsink exceeds 95°C.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Blocked intake vents below cooktop (cutlery tray too close), non-spinning cooling fan, or dried thermal paste under IGBTs.
Allow cooktop to cool 30 minutes. Clear 20mm air intake gap under cabinet. Verify brushless cooling fan spins freely when powered. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Induction power board inverter stage failure E6; breaker trips or error E6 displays when attempting to energize zones.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Short-circuited IGBT power transistor pair, cracked resonant snubber capacitor, or blown onboard printed trace fuse.
Isolate cooktop. Open chassis and measure collector-to-emitter resistance on all IGBT transistors (short = 0 Ω). Replace damaged generator module. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Electronics cooling fan motor failure E7; cooktop detects stalled or disconnected fan motor during boot diagnostics.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Tangled power cable obstructing fan blades, disconnected 12V DC fan connector, or burned fan motor IC.
Check fan blades for manual freedom of movement. Measure 12V DC across fan header pins while initiating a cooking zone. Replace fan if seized. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Pan detection resonant circuit fault E8; zone display flashes 'E8' and fails to acknowledge presence of magnetic cookware.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Degraded current sensing transformer (CT) on power module, unseated ferrite induction bars, or cracked coil wiring.
Test with a confirmed high-ferrous induction pan (magnet sticks firmly). Inspect ferrite bars beneath coil for physical damage. Check current sensor circuit. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Microcontroller configuration jumper / EEPROM mismatch E9; power board variant coding does not match user interface.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Incorrect power-limiter DIP switch setting (16A, 20A, 32A), unconfigured replacement board, or corrupted EEPROM firmware.
Inspect DIP switch block on power generator PCB. Set switches per manufacturer technical schematic for specific model wattage rating. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Electronic programmer time clock error Er00; display flashes '00:00' or error code and refuses to begin heating mode.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Mains supply blackout interruption clearing time-of-day memory or corrupted clock chip oscillator.
Press and hold the Clock or Timer button for 3 seconds, adjust the current time with selector knobs, and confirm with OK. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Cavity temperature probe circuit open or shorted Er01; oven immediately halts cooking and beeps continuously.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Defective platinum RTD sensor probe (nominal PT500: ~540 Ω at 20°C, PT1000: ~1078 Ω at 20°C), or damaged ceramic lead wires.
Isolate mains breaker. Remove rear oven panel. Disconnect temperature sensor connector and measure resistance (~540 Ω at 20°C for PT500). Replace probe if open. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Cavity high-temperature limit exceeded Er02; oven safety system triggers after cavity exceeds 320°C in non-pyrolytic baking mode.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Welded heating element relay on power PCB feeding current continuously, or drifted PT500 probe.
Cut mains power immediately and let oven cool down. Test heater relay contacts with power disconnected (must be open). Check PT500 resistance. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Tangential cooling fan motor tachometer fault Er03; oven aborts heating cycle because cabinet cooling airflow cannot be verified.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Jammed cross-flow fan wheel, seized sleeve bearings, disconnected Hall sensor harness, or open fan motor coil (~240–320 Ω).
Spin tangential blower drum by hand to check for mechanical binding. Measure fan motor winding resistance (~240–320 Ω). Check 5V DC Hall sensor signal. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.