Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: High temperature alarm in freezer compartment AL01; internal temperature rises above -9°C and audible buzzer sounds.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Door open warning signal persistent AL02; acoustic door alarm sounds and interior light remains energized with door shut.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Auto-Stop safety timeout triggered AS; all induction cooking zones shut down automatically after liquid spillover or prolonged cooking.
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Water fill timeout d01; appliance fails to fill with adequate water volume within 4 minutes of program launch.
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Condensation water reservoir full d01; dryer halts cycle and triggers acoustic water tank warning.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Fridge compartment temperature sensor failure d01; internal cold air temperature fluctuates uncontrollably.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Water intake timeout d01; tub water level does not reach wash threshold within 6 minutes of valve opening.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Condensate lift pump failure d02; water fails to pump up into collection tank and accumulates in chassis sump base.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Drain pump timeout d02; water remains in the drum after 4 minutes of continuous drain pump operation.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Ambient room temperature sensor error d03; unit cannot adapt cooling cycles to room climate variations.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Heating circuit timeout d03; water temperature fails to increase by more than 2°C within 30 minutes of wash cycle.
Immersion / Air Heating Element & Klixon Thermostat
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Drum motor drive stall d04; drive motor hums loudly or fails to turn the drum loaded with damp laundry.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Evaporator circulation fan motor failure d05; cold air does not circulate into the refrigeration compartments.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Wash motor overcurrent cutoff d06; power electronic controller trips due to excessive electric current draw by the circulation pump.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Motorized air damper flap malfunction d06; fresh food compartment either freezes contents or remains too warm.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Motor tachometer signal fault d06; drum does not rotate or motor starts then immediately stops after speed feedback loss.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Condenser cooling fan motor failure d07; compressor overheats, trips overload protector, and cooling stops.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Door interlock safety fault d07; cycle will not begin because electronic module cannot confirm closed door contact.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Alternating spray distributor valve motor fault d08; wash water does not alternate between upper and lower spray arms.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Inverter compressor drive or communication failure d08; compressor fails to start or rapidly cuts out after clicking.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Drum rotation reversal fault d08; drum rotates only in one direction during wash tumble phases.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Internal control bus communication error d09; display fascia loses synchronism with main hydraulic power board.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Automatic ice maker mechanism failure d09; ice cubes are not ejected into storage bucket or water fill fails.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Continuous uncontrolled water fill d10; water continues entering appliance after target fill level is achieved.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Main electronic control PCB memory error d10; unit resets intermittently or fails to execute temperature programs.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Abnormal heating in rinse cycle d11; water heats unexpectedly during cold water rinse phases.
Immersion / Air Heating Element & Klixon Thermostat
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Residual water detected after pumpout d12; pressure sensor fails to register empty tub state after drain sequence.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Wash pump cavitation / water fill discrepancy d14; circulation motor draws irregular current due to aerated water foam.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Inverter drum motor communication loss d15; variable speed motor controller fails to respond to main microprocessor commands.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Electronic pressure switch frequency fault d15; analog level sensor outputs erratic frequency signal to main PCB.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: Door latch open during cycle d16; cycle pauses immediately as door contact microswitch opens during active operation.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Inverter module bus link error d16; main controller loses communication with 3-phase BLDC motor inverter card.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Mains supply frequency out of bounds d18; line frequency deviates outside 47 Hz – 63 Hz operational tolerances.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / SFS Condensation & Heat Pump Tumble Dryer: User interface display communication timeout d20; display panel loses serial synchronization with main power controller.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Water distributor stepper motor fault d20; water stream cannot be directed to the selected additive compartment.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Display to power board communication loss d21; control panel lights flash or display is completely blank while machine halts.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Washer-dryer ventilation fan failure d24; process air blower fails to spin during drying phase.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Door unlock timeout at cycle completion d27; door remains securely locked after wash program finishes and drum stops.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Touch control panel link failure E1; induction zones flash 'E1' and power sliders do not respond to fingertip touch.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Induction coil temperature sensor fault E2; zone display flashes 'E2' and cuts power to prevent glass overheating.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Mains undervoltage protection trip E4; cooktop shuts down zones because electrical line voltage drops below 180 V RMS.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Electronics cooling fan motor failure E7; cooktop detects stalled or disconnected fan motor during boot diagnostics.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Pan detection resonant circuit fault E8; zone display flashes 'E8' and fails to acknowledge presence of magnetic cookware.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Microcontroller configuration jumper / EEPROM mismatch E9; power board variant coding does not match user interface.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Main power board communication timeout Er06; display module loses digital data exchange with the internal power relay board.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Steam boiler water evacuation fault Er10; drain pump fails to pump residual water out of the steam boiler.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Upper heating grill element relay fault Er11; top grill element glows red continuously without cooking program active.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Circular convection fan heating element open circuit Er13; convection forced air mode blows air without heating.
Immersion / Air Heating Element & Klixon Thermostat
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: No cookware detected or unsuitable pan base F0; zone display alternates 'F0' and heating output is withheld.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Basque electronic platform water fill fault F01; water inlet solenoid valve fails to supply water within allocated timeout.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: User interface keyboard communication timeout F1; touch control panel loses synchronization with induction power board.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Refrigerator compartment air temperature probe failure F2; display alternates temperature and fault code.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Tangential cooling fan speed error F03; fan operates at insufficient RPM or tachometer signal is missing.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: High voltage surge protection active F3; power board shuts down induction frequency generation to prevent semiconductor destruction.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Freezer compartment air temperature probe failure F3; freezer temperature control loses precision and warning flashes.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Pyrolytic latch microswitch position error F05; position feedback microswitch does not toggle when door unlatches.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Evaporator fan motor feedback failure F5; fan motor does not achieve target operating RPM during cooling demand.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Continuous water entry / water level safety fault F6; water continues to rise after program attempts shut-off.
Mechanical Pressure Switch Contacts / Inductive Frequency Sensor
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Short-circuited IGBT power semiconductor F6; circuit breaker trips with an audible pop when zone is turned on.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Door display communication fault F6; user interface loses digital connection to the main power board.
Compressor Motor Windings (Run/Start) & Defrost Heater
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Cooling fan blocked or low RPM stall F7; electronic safety cuts zone power when fan fails to achieve operational speed.
3-Phase Motor Windings / Tacho Generator / Carbon Brushes
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Control board EEPROM calibration checksum failure F9; factory power table values are corrupted and zones will not operate.
PCB Power Supply Rails & DC Bus Filter Capacitors
Electronic Control Board (PCB) & Bus Communications
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Pyrolytic door lock mechanism timeout Er04; motorized latch fails to lock the oven door when initiating self-clean mode.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Jammed door latch cam mechanism, broken lock gear motor coil (~4.5–6.0 kΩ), or pitted locking microswitch.
Inspect door lock latch above door cavity. Measure lock motor winding resistance (~4.5–6.0 kΩ). Verify microswitch contacts close (~0 Ω) when locked. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Pyrolytic door unlock failure Er05; oven door remains locked after pyrolytic cleaning completes and cavity cools below 280°C.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Deformed door latch hook under thermal stress, stuck unlock microswitch, or PT500 probe falsely reading high.
Allow oven to reach room temperature. Press door inward to relieve mechanical latch friction. Test unlock microswitch contact continuity (~0 Ω). Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Electronic Control Board (PCB) & Bus Communications
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Main power board communication timeout Er06; display module loses digital data exchange with the internal power relay board.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Loosened data ribbon harness, electrical interference spikes, or dropped 12V DC auxiliary supply rail.
Reseat multi-core data harness connecting user interface and relay power PCB. Measure 12V DC and 5V DC supply rails on test pads. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Corrupted non-volatile EEPROM storage sector caused by power grid surge during active baking.
Isolate mains breaker for 15 minutes to force microcomputer memory cold boot. If Er07 persists on power up, replace main control board. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Meat probe temperature sensor fault Er08; core food probe reads short-circuit or abnormal value when plugged into internal socket.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Internal jack socket grease contamination, punctured probe cable insulation, or damaged probe thermistor tip.
Unplug probe. Clean female jack receptacle inside oven with electronics cleaner. Measure resistance across probe plug pins with a multimeter. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
On FAGOR steam combi ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Heavy mineral limescale obstructing boiler heat transfer, open steam heater (~45–60 Ω), or defective boiler NTC (~10 kΩ at 25°C).
Execute automated descaling procedure with commercial sulfamic acid descaler. Measure boiler heating element resistance (~45–60 Ω) and boiler NTC (~10 kΩ at 25°C). Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Steam boiler water evacuation fault Er10; drain pump fails to pump residual water out of the steam boiler.
On FAGOR steam combi ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Calcium flakes wedging the mini drain pump impeller, blocked silicone drain tube, or open pump coil (~150–220 Ω).
Inspect mini drainage pump below steam generator. Clear scale obstructions from pump chamber. Measure pump coil resistance (~150–220 Ω). Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Electronic Control Board (PCB) & Bus Communications
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Upper heating grill element relay fault Er11; top grill element glows red continuously without cooking program active.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Welded or arced grill power relay contacts on the main power relay circuit board.
Disconnect mains breaker immediately. Measure grill element resistance (~22–26 Ω). Test relay contacts with power off; replace power relay PCB if shorted. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Lower heating sole element relay fault Er12; bottom oven cavity continues heating unchecked regardless of thermostat setting.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Welded relay contacts on lower bake heating circuit on main power board.
Isolate breaker. Measure bottom bake element resistance (~35–45 Ω). Measure continuity across bake relay contacts with power off (must be open). Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Circular convection fan heating element open circuit Er13; convection forced air mode blows air without heating.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Burned-out circular calrod heating element surrounding the rear convection fan (~25–32 Ω).
Disconnect power and remove rear internal fan shroud inside oven cavity. Measure resistance across circular element terminals (~25–32 Ω). Replace element. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Capacitive touch panel continuous keypress error Er14; touch control button registers continuous contact for longer than 10 seconds.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Greasy residue, condensation film over glass front, or detached conductive foam spacer under glass.
Clean front glass panel with a microfiber cloth and glass cleaner. Ensure hands are dry. Power cycle circuit breaker for 60 seconds to recalibrate capacitance. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
On FAGOR built-in ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Defective tangential cooling blower, blocked cabinetry ventilation chimney, or damaged upper heat deflector.
Turn off oven and allow cooling. Ensure kitchen cabinet has minimum 50mm rear ventilation gap. Verify tangential cooling fan runs freely. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: No cookware detected or unsuitable pan base F0; zone display alternates 'F0' and heating output is withheld.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Non-ferromagnetic cookware (copper, pure aluminum, ceramic glass), or warped base diameter smaller than 120mm.
Use an induction-compatible pan with a thick flat steel or cast-iron base. Verify with a refrigerator magnet (must stick securely to pan bottom). Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Temperature sensor probe open circuit F01; controller senses completely broken cavity temperature sensor loop.
On FAGOR ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Broken internal PT500 RTD platinum filament, disconnected connector behind rear insulation, or fractured probe wires.
Unplug oven from power. Measure probe resistance (~540 Ω at 20°C). Inspect sensor wiring behind rear fiberglass blanket. Replace probe if open. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Innova / Elegance / Fascia / FE-810 Inverter Washing Machine: Basque electronic platform water fill fault F01; water inlet solenoid valve fails to supply water within allocated timeout.
On FAGOR washing machines featuring Innova electronic architecture, dual d01-d27 / F01-F15 diagnostic telemetry, and robust motor drive with 15mm carbon brushes: Closed external supply tap, clogged inlet hose mesh, or open inlet solenoid coil (~3.8 kΩ).
Verify tap water pressure. Remove and rinse the mesh filter screen at the rear valve inlet. Measure coil resistance (~3.8 kΩ). Turn selector dial to 0, press and hold Start/Pause and Extra Rinse buttons for 6 seconds until 'F00' or display resets, then restart.
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Water inlet pressure drop error F1; flowmeter impeller does not register incoming pulses during filling phase.
On FAGOR dishwashers featuring Eco Sensor turbidity optoelectronics, Innova hydraulic distribution, and AquaStop active leak containment: Closed tap, clogged inlet valve screen, stuck flowmeter turbine, or defective reed contact on air break.
Open tap fully. Clean inline filter screen. Measure reed switch pulse closure with a multimeter while water enters air break. Press and hold the Start/Stop key for 5 seconds until the program indicator light clears and drain pump runs, then switch off.
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: User interface keyboard communication timeout F1; touch control panel loses synchronization with induction power board.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Oxidized ribbon cable pin headers, electrical line transient spikes, or defective 5V DC low-voltage regulator.
Inspect multi-strand cable linking touch panel to power module. Measure 5V DC on logic supply test pads. Reseat connectors firmly. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Defrost evaporator sensor error F1; freezer display blinks warning code and defrost cycle does not terminate properly.
On FAGOR refrigeration units featuring Innova Total No Frost dual-evaporator system, dynamic cooling column, and intelligent automated defrost cycle: Fagor Innova platform evaporator NTC sensor out of ohmic range, broken wire harness in cabinet foaming, or plug oxidation.
Measure evaporator NTC resistance at board plug: approx. 10.0 kΩ at 25°C and 32.5 kΩ at 0°C. If value deviates by >15%, replace the probe using service repair kit. Press and hold the Super Freeze and Alarm Mute pads together for 6 seconds until the beep confirms diagnostic memory cleared.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Temperature sensor probe short circuit F02; controller registers zero resistance on cavity thermal loop.
On FAGOR ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Pinch in braided high-temperature leads, crushed probe sheath touching cavity chassis, or internal short in RTD element.
Disconnect sensor at PCB plug. Measure resistance across pins (must not be zero; nominal ~540 Ω at 20°C). Inspect wiring harness for chassis contact. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Sump water evacuation timeout F2; water remains detected in the bottom sump basin after drain phase timing expires.
On FAGOR dishwashers featuring Eco Sensor turbidity optoelectronics, Innova hydraulic distribution, and AquaStop active leak containment: Blocked sink spigot connection, debris in drain pump volute, or open drain pump winding (~180–220 Ω).
Check sink drain connector and punch out membrane if newly installed. Measure drain pump motor resistance (~180–220 Ω). Press and hold the Start/Stop key for 5 seconds until the program indicator light clears and drain pump runs, then switch off.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Induction coil thermal probe circuit anomaly F2; cooking zone halts heating immediately after detecting open or shorted NTC.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Fractured coil center thermistor glass bead (~100 kΩ at 25°C), or wire severance under coil mounting disc.
Disconnect coil thermistor plug from power module. Measure resistance across probe leads (~100 kΩ at 25°C). Replace central coil sensor if damaged. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Refrigerator compartment air temperature probe failure F2; display alternates temperature and fault code.
On FAGOR refrigeration units featuring Innova Total No Frost dual-evaporator system, dynamic cooling column, and intelligent automated defrost cycle: Open-circuit or short-circuit in the refrigerator compartment NTC thermistor sensor, or disconnected harness.
Check sensor resistance at pins on main PCB: nominal 5.0 kΩ at 25°C and 16.3 kΩ at 0°C. If open or shorted, install service replacement NTC probe. Press and hold the Super Freeze and Alarm Mute pads together for 6 seconds until the beep confirms diagnostic memory cleared.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Tangential cooling fan speed error F03; fan operates at insufficient RPM or tachometer signal is missing.
On FAGOR ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Degraded blower motor run winding, dusty fan bearings, or failed Hall sensor IC.
Clean fan roller of lint and dust. Measure motor coil resistance (~240–320 Ω). Verify tachometer signal line voltage (pulses 0–5V DC). Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Heating system malfunction F3; temperature fails to climb during wash segment, aborting heating cycle.
On FAGOR dishwashers featuring Eco Sensor turbidity optoelectronics, Innova hydraulic distribution, and AquaStop active leak containment: Open heater resistance element (~25–28 Ω), blown inline thermal fuse, or open safety pressure switch.
Measure heating element terminals for continuity (~25–28 Ω). Verify safety pressure switch closes when circulation pump creates water pressure. Press and hold the Start/Stop key for 5 seconds until the program indicator light clears and drain pump runs, then switch off.
Electronic Control Board (PCB) & Bus Communications
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: High voltage surge protection active F3; power board shuts down induction frequency generation to prevent semiconductor destruction.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Lightning strike transient, sudden line inductive load switching, or missing neutral on 400V 3-phase hookup.
Isolate cooktop for 10 minutes. Check supply voltage across all terminals (must be steady 230V AC to Neutral). Ensure neutral is connected solidly. Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Freezer compartment air temperature probe failure F3; freezer temperature control loses precision and warning flashes.
On FAGOR refrigeration units featuring Innova Total No Frost dual-evaporator system, dynamic cooling column, and intelligent automated defrost cycle: Freezer air NTC sensor failure, wire harness pinch at cabinet bottom, or moisture infiltration into sensor body.
Measure freezer sensor resistance: expected approx. 10.0 kΩ at 25°C, 32.5 kΩ at 0°C, and 85 kΩ at -18°C. Replace sensor if resistance does not match temperature curve. Press and hold the Super Freeze and Alarm Mute pads together for 6 seconds until the beep confirms diagnostic memory cleared.
Fagor Masterchef / Innova / 6H Pyrolytic Multi-Function Oven: Pyrolytic door lock motor drive failure F04; latch actuator fails to reach locked position within 60 seconds.
On FAGOR ovens featuring Masterchef 6H pyrolytic thermal management, high-flow tangential cooling turbine, and digital programmer interface: Open actuator motor coil (~4.8 kΩ), cracked reduction gears, or door hook misalignment.
Check door latch motor coil resistance (~4.8 kΩ). Verify latch mechanism rotates freely without binding against chassis sheet metal. Return function selector to 0, isolate the power distribution breaker for 60 seconds, restore power and configure the clock.
Fagor Eco Sensor / Innova / 1LV / 2LV Dishwasher: Sump NTC sensor open or short circuit F4; controller senses disconnected or shorted thermal sensor circuit.
On FAGOR dishwashers featuring Eco Sensor turbidity optoelectronics, Innova hydraulic distribution, and AquaStop active leak containment: Defective NTC thermistor element (~47 kΩ at 25°C), disconnected wiring harness, or moisture bridging pins.
Unplug NTC sensor from sump. Measure resistance across probe pins (~47 kΩ at 25°C). Inspect wiring harness for pin push-back. Press and hold the Start/Stop key for 5 seconds until the program indicator light clears and drain pump runs, then switch off.
Fagor Innova Induction / IF / 2IF / 3IF High-Power Cooktop: Generator DC bus undervoltage trip F4; internal filtered rectified voltage collapses under induction pulse load.
On FAGOR cooktops utilizing Innova high-frequency induction generator, ferromagnetic pan detection resonance, and rapid booster stages: Degraded primary bridge rectifier, dried-out high-voltage DC filter electrolytic capacitors, or poor supply terminal connection.
Check mains terminal block screw torque. Measure rectified DC bus voltage across bulk capacitors (must maintain >290V DC under zone operation). Clear and dry cooktop surface, disconnect mains power breaker for 60 seconds, reconnect and hold Key Padlock sensor for 5 seconds.
Fagor Innova Total No Frost / FFA Multi-Airflow Refrigerator: Defrost heater cycle timeout F4; maximum defrost heating duration exceeded without reaching cutout temperature.
On FAGOR refrigeration units featuring Innova Total No Frost dual-evaporator system, dynamic cooling column, and intelligent automated defrost cycle: Defective calrod defrost element (~280 Ω), open thermal fuse (72°C), or poor thermal contact of defrost NTC on evaporator.
Measure defrost heater: expect ~260–300 Ω. Measure inline thermal safety fuse: must read 0 Ω. Confirm defrost NTC is tightly clamped to the evaporator tube. Press and hold the Super Freeze and Alarm Mute pads together for 6 seconds until the beep confirms diagnostic memory cleared.